M-type refractive index profile erbium-doped fiber for high-efficiency multicore EDFA.

Cladding-pumped multicore erbium-doped fiber is an important element for future spatial division multiplexing (SDM) amplification. We propose an M-type erbium-doped multicore fiber to achieve high-efficiency SDM amplification. The performance of cladding-pumped erbium-doped fiber with a central refractive index depression has been investigated, and the M-type fiber has better amplification performance than conventional fibers by reducing the signal mode overlap with the doped region. The experiment results show that the M-type 4-core erbium-doped fiber has a gain improvement of 2.8 dB compared with conventional 4-core fiber. The pump conversion efficiency (PCE) has been enhanced from 4.47% to 8.01%. For a 7.0 W pump power at 976 nm, the M-type fiber exhibits an average gain of 20.0 dB and an average noise fiber of 6.8 dB at the L-band. The core-to-core gain variation is less than 1.6 dB.

High-efficiency cladding-pumped Er/Yb co-doped alumino-phosphosilicate fiber for an extended L-band amplification.

Extending the gain bandwidth of L-band optical fiber amplifier has provoked a widespread interest. To date, achieving a high-efficiency extended L-band amplification remains a challenge. Here, we report a cladding-pumped Er/Yb co-doped alumino-phosphosilicate fiber, prepared by the modified chemical vapor deposition process. We demonstrate the efficiency of alumino-phosphosilicate glass for cladding-pumped Er/Yb co-doped fiber, with a gain per unit fiber length of 0.45 dB/m at 1625 nm and a gain ripple of ∼9.4 dB. For 0.8 W pump power, the fiber exhibits a 20 dB gain bandwidth covering 1575-1625 nm and 6.9 dB noise figure at 1625 nm. Additionally, the utilization of multi-mode laser diode enables further significant power savings and cost reduction. To the best of our knowledge, Er/Yb co-doped fiber in alumino-phosphosilicate glass is first proposed, with a cladding-pumped scheme for enhancing an extended L-band performance.

High bismuth-doped germanosilicate fiber for efficient E + S-band amplification.

Bismuth-doped germanosilicate fiber (BGSF), the active media of fiber amplifiers, has attracted widespread attention. Here, we report a BGSF with a high bismuth concentration of 0.075 wt. % and achieve high-efficiency E + S-band amplification, which was prepared by the modified chemical vapor deposition (MCVD) process. The small signal absorption (SSA) and unsaturated loss (UL) of BGSF at 1310 nm are 1.32 and 0.11 dB/m, respectively. The results show a record with only 45 m BGSF was created, to the best of our knowledge, which provides a maximum gain of 39.24 dB with an NF of 6.2 dB at 1430 nm under -20 dBm input signal power.

Extended L-band 4-Core Er/Yb co-doped fiber amplifier based on 1018†nm cladding pumping.

The extended L-band 4-core Er/Yb co-doped fiber and amplifier (MC-EYDFA) is first proposed and demonstrated, to the best of our knowledge, for space division multiplexing combined with wavelength division multiplexing application. The fiber core co-doped with Er/Yb/P is adopted for bandwidth expansion, and the long wavelength extends to 1625 nm. Numerical simulations further show that efficient amplification and higher saturation power are achieved with the 1018 nm cladding pumping. Based on the integrated 4-core fiber amplifier, an average gain of ∼22 dB covering 1575-1625 nm is experimentally obtained with a 4 W pump power and a 3 dBm total signal power, and the max core-dependent gain (CDG) variation is measured to be 1.7 dB.

Er/Yb co-doped 345-W all-fiber laser at 1535 nm using hybrid fiber.

The 1.5-µm fiber laser is widely used in the fields of laser lidar, remote sensing, and gas monitoring because of its advantages of being eye-safe and exhibiting low atmospheric transmission loss. However, due to the ∼1-µm amplified spontaneous emission (ASE) of the Er/Yb co-doped fiber (EYDF), it is difficult to improve the laser power. Here, we simulated the effect of the Er3+ concentration and the seed power on ∼1-µm ASE, and fabricated a large mode area EYDF by the modified chemical vapor deposition process. Additionally, a piece of ytterbium-doped fiber was introduced into the master oscillator power amplifier (MOPA) configuration to absorb the generated ∼1-µm ASE simultaneously. Experimental results show that an output power of 345 W with a slope efficiency of 43% at 1535 nm is obtained in an all-fiber configuration, profiting from effective suppression of ∼ 1-µm ASE. To the best of our knowledge, this is the highest output power available with an Er/Yb co-doped fiber from an all-fiber MOPA configuration.

High-efficiency cladding-pumped 4-core erbium-doped fiber with a pedestal for space division multiplexing amplification.

A cladding-pumped 4-core erbium-doped fiber (4C-EDF) with a pedestal structure has been firstly, to the best of our knowledge, proposed and fabricated for space division multiplexing (SDM) amplification. The numerical simulation shows that the index-raised pedestal around the fiber core can improve power conversion efficiency (PCE) by enhancing pump power usage. Compared with conventional 4C-EDF, the 4C-EDF with a pedestal has a gain improvement of 4.5 dB and a PCE enhancement of 91.8%, according to the experimental results (pedestal fiber: 9.55%, conventional fiber: 4.98%). For a 6 dBm total input signal power at L-band and a 7.8 W pump power at 976 nm, the pedestal 4C-EDF shows an average gain of 25 dB and an average noise figure (NF) of 6.5 dB over all cores in the wavelength range of 1570.41 nm to 1610.87 nm. The core-to-core gain variation is less than 2 dB.

Extended L-band few-mode Er/Yb Co-doped fiber amplifier with a cladding-pumped pseudo-two-stage configuration.

Spatial division multiplexing (SDM) is one of the most important technologies that may help to solve the future capacity crisis. However, to date, SDM optical amplification is still a challenge for its application. Herein, we numerically and experimentally demonstrated a few-mode Er/Yb co-doped fiber amplifier (FM-EYDFA) for extended L-band operation. A double cladding Er/Yb co-doped fiber was fabricated to expand the L-band bandwidth and a novel, to the best of our knowledge, cladding-pumped pseudo-two-stage amplification configuration was proposed to enhance the L-band gain. With an initial signal power of -16.8 dBm and an injected pump power of 8.8 W at 940 nm, the 20-dB gain range was covered to 1620 nm for two-mode groups of LP01 and LP11. Importantly, the average gain of 25 dB and average differential modal gain (DMG) of <1 dB were obtained in the wavelength range of 1570-1620 nm for all modes. Our results suggest that the cladding-pumped pseudo-two-stage amplifier based on Er/Yb co-doped fiber providing low DMG, and broad bandwidth has a great potential for increasing the future SDM capacity.

Extending the L-band amplification to 1623 nm using Er/Yb/P co-doped phosphosilicate fiber.

The gain bandwidth of the erbium-doped fiber amplifier limits the enhancement of the transmission capacity in optical fiber communication systems. This Letter reports an erbium-ytterbium co-doped phosphosilicate fiber, which is expected to increase transmission capacity by extending the L-band gain bandwidth to 1623 nm. The fiber was fabricated by modified chemical vapor deposition combined with solution doping technology. The mechanism of bandwidth-expansion by inhibiting the signal excited-state absorption was investigated. When the signal power and pump power were maintained at -3.7dBm and ∼720mW at 1480 nm, the 20 dB gain range was extended out to 1623 nm. Additionally, the noise figure at 1623 nm decreased to 6.01 dB, with 23 dBm saturated output power. The results show that the erbium-ytterbium co-doped phosphosilicate fiber has a great potential for extending L-band amplification.