Analytically useful blue chemiluminescence from a water-soluble iridium(III) complex containing a tetraethylene glycol functionalised triazolylpyridine ligand.

We examine [Ir(df-ppy)2(pt-TEG)](+) as the first highly water soluble, blue-luminescent iridium(III) complex for chemiluminescence detection. Marked differences in selectivity were observed between the new complex and the conventional [Ru(bpy)3](2+) reagent, which will enable this mode of detection to be extended to new areas of application.

Integrated RNA extraction and RT-PCR for semi-quantitative gene expression studies on a microfluidic device.

This paper describes the development of a microfluidic methodology, using RNA extraction and reverse transcription PCR, for investigating expression levels of cytochrome P450 genes. Cytochrome P450 enzymes are involved in the metabolism of xenobiotics, including many commonly prescribed drugs, therefore information on their expression is useful in both pharmaceutical and clinical settings. RNA extraction, from rat liver tissue or primary rat hepatocytes, was performed using a silica-based solid-phase extraction technique. Following elution of the purified RNA, amplification of target sequences for the housekeeping gene, glyceraldehyde-3-phosphate dehydrogenase (GAPDH) and the cytochrome P450 gene CYP1A2, was carried out using a one-step reverse transcription PCR. Once the microfluidic methodology had been optimized, analysis of control and 3-methylcholanthrene-induced primary rat hepatocytes were used to evaluate the system. As expected, GAPDH was consistently expressed, whereas CYP1A2 levels were found to be raised in the drug-treated samples. The proposed system offers an initial platform for development of both rapid throughput analyzers for pharmaceutical drug screening and point-of-care diagnostic tests to aid provision of drug regimens, which can be tailor-made to the individual patient.

Maternal hair selenium levels as a possible long-term nutritional indicator of recurrent pregnancy loss.

BACKGROUND: Approximately 1% of all couples trying to conceive will suffer from recurrent pregnancy loss (RPL). Nutritional deficiencies have been postulated as a possible cause of RPL and in particular, selenium deficiency has been associated with reproductive failure in animal studies and more recently, in some human studies. This study was undertaken to assess the maternal hair selenium levels in women with RPL without an identified cause and to compare these results with those of women with successful reproductive histories. METHODS: Twenty four patients with RPL and twenty four control subjects with at least one successful pregnancy and no pregnancy failures, who were matched for age and ethnicity, were recruited. A questionnaire was completed, which included demographic and social information and a dietary history. Hair samples were collected and analyzed for selenium content by inductively coupled plasma mass spectrometry. RESULTS: The control subjects had a higher mean income and had completed more years of education compared with the RPL patients. There was no significant difference in the intake of selenium rich foods between the 2 groups. The patients, however, consumed significantly more fruit, cheese, potatoes and chocolate than the controls. The median (range) selenium content was 0.80 ppm (0.19-4.15) and 0.68 ppm (0.43-3.76) in patients and controls respectively (Mann Whitney U test 209.5 p = 0.74). CONCLUSIONS: While there were significant differences in the 2 groups with regard to resources, education and diet our results show that hair selenium concentrations and dietary selenium intake, were similar in the two groups. Both groups had low levels of this important element.

Evaluation of heart tissue viability under redox-magnetohydrodynamics conditions: toward fine-tuning flow in biological microfluidics applications.

A microfluidic system containing a chamber for heart tissue biopsies, perfused with Krebs-Henseleit buffer containing glucose and antibiotic (KHGB) using peristaltic pumps and continuously stimulated, was used to evaluate tissue viability under redox-magnetohydrodynamics (redox-MHD) conditions. Redox-MHD possesses unique capabilities to control fluid flow using ionic current from oxidation and reduction processes at electrodes in a magnetic field, making it attractive to fine-tune fluid flow around tissues for "tissue-on-a-chip" applications. The manuscript describes a parallel setup to study two tissue samples simultaneously, and 6-min static incubation with Triton X100. Tissue viability was subsequently determined by assaying perfusate for lactate dehydrogenase (LDH) activity, where LDH serves as an injury marker. Incubation with KHGB containing 5 mM hexaammineruthenium(III) (ruhex) redox species with and without a pair of NdFeB magnets (∼ 0.39 T, placed parallel to the chamber) exhibited no additional tissue insult. MHD fluid flow, viewed by tracking microbeads with microscopy, occurred only when the magnet was present and stimulating electrodes were activated. Pulsating MHD flow with a frequency similar to the stimulating waveform was superimposed over thermal convection (from a hotplate) for Triton-KHGB, but fluid speed was up to twice as fast for ruhex-Triton-KHGB. A large transient ionic current, achieved when switching on the stimulating electrodes, generates MHD perturbations visible over varying peristaltic flow. The well-controlled flow methodology of redox-MHD is applicable to any tissue type, being useful in various drug uptake and toxicity studies, and can be combined equally with on- or off-device analysis modalities.

On-chip integrated labelling, transport and detection of tumour cells.

Microflow cytometry represents a promising tool for the investigation of diagnostic and prognostic cellular cancer markers, particularly if integrated within a device that allows primary cells to be freshly isolated from the solid tumour biopsies that more accurately reflect patient-specific in vivo tissue microenvironments at the time of staining. However, current tissue processing techniques involve several sequential stages with concomitant cell losses, and as such are inappropriate for use with small biopsies. Accordingly, we present a simple method for combined antibody-labelling and dissociation of heterogeneous cells from a tumour mass, which reduces the number of processing steps. Perfusion of ex vivo tissue at 4°C with antibodies and enzymes slows cellular activity while allowing sufficient time for the diffusion of minimally active enzymes. In situ antibody-labelled cells are then dissociated at 37°C from the tumour mass, whereupon hydrogel-filled channels allow the release of relatively low cell numbers (<1000) into a biomimetic microenvironment. This novel approach to sample processing is then further integrated with hydrogel-based electrokinetic transport of the freshly liberated fluorescent cells for downstream detection. It is anticipated that this integrated microfluidic methodology will have wide-ranging biomedical and clinical applications.

Microscreening toxicity system based on living magnetic yeast and gradient chips.

There is an increasing demand for easy and cost-effective methods to screen the toxicological impact of the growing number of chemical mixtures being generated by industry. Such a screening method has been developed using viable, genetically modified green fluorescent protein (GFP) reporter yeast that was magnetically functionalised and held within a microfluidic device. The GFP reporter yeast was used to detect genotoxicity by monitoring the exposure of the cells to a well-known genotoxic chemical (methyl methane sulfonate, MMS). The cells were magnetised using biocompatible positively charged PAH-stabilised magnetic nanoparticles with diameters around 15 nm. Gradient mixing was utilised to simultaneously expose yeast to a range of concentrations of toxins, and the effective fluorescence emitted from the produced GFP was measured. The magnetically enhanced retention of the yeast cells, with their facile subsequent removal and reloading, allowed for very convenient and rapid toxicity screening of a wide range of chemicals. This is the first report showing magnetic yeast within microfluidic devices in a simple bioassay, with potential applications to other types of fluorescent reporter yeast in toxicological and biomedical research. The microfluidic chip offers a simple and low-cost screening test that can be automated to allow multiple uses (adapted to different cell types) of the device on a wide range of chemicals and concentrations.

Scaling up of continuous-flow, microwave-assisted, organic reactions by varying the size of Pd-functionalized catalytic monoliths.

A product-scalable, catalytically mediated flow system has been developed to perform Suzuki-Miyaura reactions under a microwave heating regime, in which the volumetric throughput of a Pd-supported silica monolith can be used to increase the quantity of the product without changing the optimal operating conditions. Two silica monoliths (both 3 cm long), with comparable pore diameters and surface areas, were fabricated with diameters of 3.2 and 6.4 mm to give volumetric capacities of 0.205 and 0.790 mL, respectively. The two monoliths were functionalized with a loading of 4.5 wt % Pd and then sealed in heat-shrinkable Teflon(®) tubing to form a monolithic flow reactor. The Pd-supported silica monolith flow reactor was then placed into the microwave cavity and connected to an HPLC pump and a backpressure regulator to minimize the formation of gas bubbles. The flow rate and microwave power were varied to optimize the reactant contact time and temperature, respectively. Under optimal reaction conditions the quantity of product could be increased from 31 mg per hour to 340 mg per hour simply by changing the volumetric capacity of the monolith.

Microfluidic perfusion system for maintaining viable heart tissue with real-time electrochemical monitoring of reactive oxygen species.

A microfluidic device has been developed to maintain viable heart tissue samples in a biomimetic microenvironment. This device allows rat or human heart tissue to be studied under pseudo in vivo conditions. Effluent levels of lactate dehydrogenase and hydrogen peroxide were used as markers of damaged tissue in combination with in situ electrochemical measurement of the release of reactive oxygen species (ROS). The parameters for perfusion were optimized to maintain biopsies of rat right ventricular or human right atrial tissue viable for up to 5 and 3.5 hours, respectively. Electrochemical assessment of the oxidation current of total ROS, employing cyclic voltammetry, gave results in real-time that were in good agreement to biochemical assessment using conventional, off-chip, commercial assays. This proof-of-principle, integrated microfluidic device, may be exploited in providing a platform technology for future cardiac research, offering an alternative approach for investigating heart pathophysiology and facilitating the development of new therapeutic strategies.

Rapid PCR amplification using a microfluidic device with integrated microwave heating and air impingement cooling.

A microwave heating system is described for performing polymerase chain reaction (PCR) in a microfluidic device. The heating system, in combination with air impingement cooling, provided rapid thermal cycling with heating and cooling rates of up to 65 degrees C s(-1) and minimal over- or under-shoot (+/-0.1 degrees C) when reaching target temperatures. In addition, once the required temperature was reached it could be maintained with an accuracy of +/-0.1 degrees C. To demonstrate the functionality of the system, PCR was successfully performed for the amplification of the Amelogenin locus using heating rates and quantities an order of magnitude faster and smaller than current commercial instruments.

Microfluidic-based measurements of cytochrome P450 enzyme activity of primary mammalian hepatocytes.

A microfluidic-based system was developed for the in situ monitoring of the 7-ethoxyresorufin O-dealkylation (EROD) activity of primary rat hepatocytes by measuring the fluorescent intensity of both cells and their surrounding media. The microfluidic chip was designed to allow the cell suspension and test reagent to be introduced in a layer-by-layer flow format, thereby resulting in a short mixing time by diffusion. A good linear relationship was obtained between the resorufin concentration up to 30 microM and fluorescent intensity over the chip's circular chamber area. The EROD activity was determined with 3-methylcholanthrene (3-MC)-induced hepatocytes. The inhibition effect of alpha-naphthoflavone was also examined on EROD activity resulting in an IC(50) value of 12.98 microM.

Detection of nitric oxide in tissue samples by ESI-MS.

A novel method to determine nitric oxide (NO) in biological tissue samples with minimal interference from the cellular detritus is described. Methylpiperazinobenzenediamine, consisting of an o-phenylenediamine and a methyl piperazine group, was chosen as a probe for the detection of NO by mass spectrometry (MS) in biological tissue samples. The o-phenylenediamine group reacts with NO to form a characteristic benzotriazole. The product was identified using electrospray ionization mass spectrometry (ESI-MS) and the method validated within the range of 95-1900 nM. NO levels associated with tissue biopsies (approximately 10 mg) from rat vasculature and intestine tissue biopsies have been successfully determined. The different rates of NO generated from tissue samples under hypoxic and normoxic conditions have been studied by this simple and sensitive method.

Development of a bi-functional silica monolith for electro-osmotic pumping and DNA clean-up/extraction using gel-supported reagents in a microfluidic device.

A silica monolith used to support both electro-osmotic pumping (EOP) and the extraction/elution of DNA coupled with gel-supported reagents is described. The benefits of the combined EOP extraction/elution system were illustrated by combining DNA extraction and gene amplification using the polymerase chain reaction (PCR) process. All the reagents necessary for both processes were supported within pre-loaded gels that allow the reagents to be stored at 4 degrees C for up to four weeks in the microfluidic device. When carrying out an analysis the crude sample only needed to be hydrodynamically introduced into the device which was connected to an external computer controlled power supply via platinum wire electrodes. DNA was extracted with 65% efficiency after loading lysed cells onto a silica monolith. Ethanol contained within an agarose gel matrix was then used to wash unwanted debris away from the sample by EOP (100 V cm(-1) for 5 min). The retained DNA was subsequently eluted from the monolith by water contained in a second agarose gel, again by EOP using an electric field of 100 V cm(-1) for 5 min, and transferred into the PCR reagent containing gel. The eluted DNA in solution was successfully amplified by PCR, confirming that the concept of a complete self-contained microfluidic device could be realised for DNA sample clean up and amplification, using a simple pumping and on-chip reagent storage methodology.

Development of a microfluidic device for the maintenance and interrogation of viable tissue biopsies.

A microfluidic based experimental methodology has been developed that offers a biomimetic microenvironment in which pseudo in vivo tissue studies can be carried out under in vitro conditions. Using this innovative technique, which utilizes the inherent advantages of microfluidic technology, liver tissue has been kept in a viable and functional state for over 70 h during which time on-chip cell lysis has been repeatedly performed. Tissue samples were also disaggregated in situ on-chip into individual primary cells, using a collagenase digestion procedure, enabling further cell analysis to be carried out off-line. It is anticipated that this methodology will have a wide impact on biological and clinical research in fields such as cancer prognosis and treatment, drug development and toxicity, as well as enabling better fundamental research into tissue/cell processes.

Novel inorganic polymer derived microreactors for organic microchemistry applications.

Microreactors fabricated with optically transparent inorganic polymers from two types of precursors using a UV-microimprinting process demonstrated reliable solvent resistance and capability for performing three model organic synthetic reactions, which were compared with batch systems and glass based microreactors.

Characterization of cellular chemical dynamics using combined microfluidic and Raman techniques.

The integration of a range of technologies including microfluidics, surface-enhanced Raman scattering and confocal microspectroscopy has been successfully used to characterize in situ single living CHO (Chinese hamster ovary) cells with a high degree of spatial (in three dimensions) and temporal (1 s per spectrum) resolution. Following the introduction of a continuous flow of ionomycin, the real time spectral response from the cell was monitored during the agonist-evoked Ca(2+) flux process. The methodology described has the potential to be used for the study of the cellular dynamics of a range of signalling processes.

The use of solid-supported reagents for the multi-step synthesis of analytically pure alpha,beta-unsaturated compounds in miniaturized flow reactors.

Micro reaction technology offers a safe, controllable and information rich technique suitable for the long-term production of pharmaceutical agents and fine chemicals. To date however, few of the syntheses performed using this technology have addressed the problems associated with product purification. With this in mind, we report herein the incorporation of multiple supported reagents into EOF-based miniaturized flow reactors for the two-step synthesis of analytically pure compounds. Using this approach, the successful synthesis of 20 alpha,beta-unsaturated compounds in excellent yields (>99.1%) and purities (>99.9%) has been achieved, illustrating significant improvements compared to traditional batch techniques.

Scaling out of electrolyte free electrosynthesis in a micro-gap flow cell.

The electro-reductive coupling of activated olefins and benzyl bromide derivatives has been selected to compare the performance of single and multiple channel (scaled-out) micro-gap electrochemical flow reactors. Two working electrode configurations were evaluated; in the first a single set of electrodes was used in conjunction with a multiple flow manifold to give two and four separate flow channels; in the second independent electrodes were used within the same flow manifold. Problems with shunt currents and Joule heating in the first configuration meant that only the second configuration was reliable, giving results comparable to those obtained for the single flow cell. Excellent yields of the coupling products such as 2-benzyl-succinic acid dimethyl ester and derivatives were obtained. This demonstrates micro reactor scale-out for unsupported electrosyntheses.

The use of electroosmotic flow as a pumping mechanism for semi-preparative scale continuous flow synthesis.

By employing a series of reactions we demonstrate the use of electroosmotic flow as a continuous pumping mechanism suitable for semi-preparative scale synthesis, affording an array of small organic compounds, of analytical purity, with yields ranging from 0.57-1.71 g h(-1).

Evaluation of coloured materials in microfluidic flow-cells for chemiluminescence detection.

Recent advances in the construction of chemiluminescence flow-cells has included high precision milling of channels into a range of different polymer materials, in efforts to maximise the transfer of light from the chemical reaction to the photodetector. However, little is known of the extent that the colour of polymer materials will influence this transfer. This may become increasingly important as chemiluminescence detection zones are integrated with other operations within microfluidic devices or micro total analysis systems (µTAS). Herein, we compare microfluidic flow-cells fabricated from five polymer sheets (clear, white, black, red, blue), using two flow-cell designs (spiral and serpentine), two modes of photodetection, and four chemiluminescence reactions that provide a range of different emission colours. The direct transfer of light from the reaction within the white flow-cell channel to the photodetector made only minor contributions (10%-20%) to the measured intensity, with the majority of the measured light first interacting with the polymer material into which the channels were machined. The extent that the emitted light was absorbed or reflected by the coloured polymer materials was dependent on not only the properties of the polymer, but also the spectral distribution of the chemiluminescence. The changes in chemiluminescence intensities from absorption of light by the flow-cell materials can be accompanied by distortion of the spectral distribution.