Realization of an Asymmetric Non-Aqueous Redox Flow Battery through Molecular Design to Minimize Active Species Crossover and Decomposition.

This communication presents a mechanism-based approach to identify organic electrolytes for non-aqueous redox flow batteries (RFBs). Symmetrical flow cell cycling of a pyridinium anolyte and a cyclopropenium catholyte resulted in extensive capacity fade due to competing decomposition of the pyridinium species. Characterization of this decomposition pathway enabled the rational design of next-generation anolyte/catholyte pairs with dramatically enhanced cycling performance. Three factors were identified as critical for slowing capacity fade: (1) separating the anolyte-catholyte in an asymmetric flow cell using an anion exchange membrane (AEM); (2) moving from monomeric to oligomeric electrolytes to limit crossover through the AEM; and (3) removing the basic carbonyl moiety from the anolyte to slow the protonation-induced decomposition pathway. Ultimately, these modifications led to a novel anolyte-catholyte pair that can be cycled in an AEM-separated asymmetric RFB for 96 h with >95 % capacity retention at an open circuit voltage of 1.57 V.

Developing a Predictive Solubility Model for Monomeric and Oligomeric Cyclopropenium-Based Flow Battery Catholytes.

The implementation of redox active organics in nonaqueous redox flow batteries requires the design of molecules that exhibit high solubility (>1 M) in all battery-relevant redox states. Methods for forecasting nonaqueous solubility would be valuable for streamlining the identification of promising structures. Herein we report the development of a workflow to parametrize and predict the solubility of conformationally flexible tris(dialkylamino)cyclopropenium (CP) radical dications. A statistical model is developed through training on monomer species. Ultimately, this model is used to predict new monomeric and dimeric CP derivatives with solubilities of >1 M in acetonitrile in all oxidation states. The most soluble CP monomer exhibits high stability to electrochemical cycling at 1 M in acetonitrile without a supporting electrolyte in a symmetrical flow cell.

Diketopyrrolopyrrole Polymers for Organic Solar Cells.

Conjugated polymers have been extensively studied for application in organic solar cells. In designing new polymers, particular attention has been given to tuning the absorption spectrum, molecular energy levels, crystallinity, and charge carrier mobility to enhance performance. As a result, the power conversion efficiencies (PCEs) of solar cells based on conjugated polymers as electron donor and fullerene derivatives as electron acceptor have exceeded 10% in single-junction and 11% in multijunction devices. Despite these efforts, it is notoriously difficult to establish thorough structure-property relationships that will be required to further optimize existing high-performance polymers to their intrinsic limits. In this Account, we highlight progress on the development and our understanding of diketopyrrolopyrrole (DPP) based conjugated polymers for polymer solar cells. The DPP moiety is strongly electron withdrawing and its polar nature enhances the tendency of DPP-based polymers to crystallize. As a result, DPP-based conjugated polymers often exhibit an advantageously broad and tunable optical absorption, up to 1000 nm, and high mobilities for holes and electrons, which can result in high photocurrents and good fill factors in solar cells. Here we focus on the structural modifications applied to DPP polymers and rationalize and explain the relationships between chemical structure and organic photovoltaic performance. The DPP polymers can be tuned via their aromatic substituents, their alkyl side chains, and the nature of the π-conjugated segment linking the units along the polymer chain. We show that these building blocks work together in determining the molecular conformation, the optical properties, the charge carrier mobility, and the solubility of the polymer. We identify the latter as a decisive parameter for DPP-based organic solar cells because it regulates the diameter of the semicrystalline DPP polymer fibers that form in the photovoltaic blends with fullerenes via solution processing. The width of these fibers and the photon energy loss, defined as the energy difference between optical band gap and open-circuit voltage, together govern to a large extent the quantum efficiency for charge generation in these blends and thereby the power conversion efficiency of the photovoltaic devices. Lowering the photon energy loss and maintaining a high quantum yield for charge generation is identified as a major pathway to enhance the performance of organic solar cells. This can be achieved by controlling the structural purity of the materials and further control over morphology formation. We hope that this Account contributes to improved design strategies of DPP polymers that are required to realize new breakthroughs in organic solar cell performance in the future.

Dichotomous Role of Exciting the Donor or the Acceptor on Charge Generation in Organic Solar Cells.

In organic solar cells, photoexcitation of the donor or acceptor phase can result in different efficiencies for charge generation. We investigate this difference for four different 2-pyridyl diketopyrrolopyrrole (DPP) polymer-fullerene solar cells. By comparing the external quantum efficiency spectra of the polymer solar cells fabricated with either [60]PCBM or [70]PCBM fullerene derivatives as acceptor, the efficiency of charge generation via donor excitation and acceptor excitation can both be quantified. Surprisingly, we find that to make charge transfer efficient, the offset in energy between the HOMO levels of donor and acceptor that govern charge transfer after excitation of the acceptor must be larger by ∼0.3 eV than the offset between the corresponding two LUMO levels when the donor is excited. As a consequence, the driving force required for efficient charge generation is significantly higher for excitation of the acceptor than for excitation of the donor. By comparing charge generation for a total of 16 different DPP polymers, we confirm that the minimal driving force, expressed as the photon energy loss, differs by about 0.3 eV for exciting the donor and exciting the acceptor. Marcus theory may explain the dichotomous role of exciting the donor or the acceptor on charge generation in these solar cells.

High quantum efficiencies in polymer solar cells at energy losses below 0.6 eV.

Diketopyrrolopyrrole-based conjugated polymers bridged with thiazole units and different donors have been designed for polymer solar cells. Quantum efficiencies above 50% have been achieved with energy loss between optical band gap and open-circuit voltage below 0.6 eV.

Small-bandgap semiconducting polymers with high near-infrared photoresponse.

Lowering the optical bandgap of conjugated polymers while maintaining a high efficiency for photoinduced charge transfer to suitable electron acceptors such as fullerene has remained a formidable challenge in the area of organic photovoltaics. Here we present the synthesis and application of a series of ultra-small-bandgap donor-acceptor polymers composed of diketopyrrolopyrrole as acceptor and pyrrole-based groups as strong donors. The HOMO energy levels of the polymers can be progressively increased by increasing the donor strength while the LUMO level remains similar, resulting in optical bandgaps between 1.34 and 1.13 eV. Solar cells based on these polymers blended with fullerene derivatives show a high photoresponse in the near-infrared (NIR) and good photovoltaic characteristics, with power conversion efficiencies of 2.9-5.3%. The photoresponse reaches up to 50% external quantum efficiency at 1000 nm and extends to 1200 nm. With the use of a retro-reflective foil to optimize light absorption, high photocurrents up to 23.0 mA cm(-2) are achieved under standard solar illumination conditions. These ultra-small-bandgap polymers are excellent candidates for use in multi-junction applications and NIR organic photodetectors.

Homocoupling defects in diketopyrrolopyrrole-based copolymers and their effect on photovoltaic performance.

We study the occurrence and effect of intrachain homocoupling defects in alternating push-pull semiconducting PDPPTPT polymers based on dithienyl-diketopyrrolopyrrole (TDPPT) and phenylene (P) synthesized via a palladium-catalyzed cross-coupling polymerization. Homocoupled TDPPT-TDPPT segments are readily identified by the presence of a low-energy shoulder in the UV/vis/NIR absorption spectrum. Remarkably, the signatures of these defects are found in many diketopyrrolopyrrole (DPP)-based copolymers reported in the literature. The defects cause a reduction of the band gap, a higher highest occupied molecular orbital (HOMO) level, a lower lowest unoccupied molecular orbital (LUMO) level, and a localization of these molecular orbitals. By synthesizing copolymers with a predefined defect concentration, we demonstrate that their presence reduces the short-circuit current and open-circuit voltage of solar cells based on blends of PDPPTPT with [70]PCBM. In virtually defect-free PDPPTPT, the power conversion efficiency is as high as 7.5%, compared to 4.5-5.6% for polymers containing 20% to 5% defects.

Efficient tandem and triple-junction polymer solar cells.

We demonstrate tandem and triple-junction polymer solar cells with power conversion efficiencies of 8.9% and 9.6% that use a newly designed, high molecular weight, small band gap semiconducting polymer and a matching wide band gap polymer.

Universal correlation between fibril width and quantum efficiency in diketopyrrolopyrrole-based polymer solar cells.

For a series of six diketopyrrolopyrrole (DPP)-based conjugated polymers, we establish a direct correlation between their external quantum efficiencies (EQE) in organic solar cells and the fibrillar microstructure in the blend. The polymers consist of electron-deficient DPP units, carrying long branched 2'-decyltetradecyl (DT) side chains for solubility, that alternate along the main chain with electron-rich aromatic segments comprising benzene, thiophene, or fused aromatic rings. The high molecular weight DT-DPP polymers were incorporated in bulk heterojunction solar cells with [6,6]-phenyl-C71-butyric acid methyl ester ([70]PCBM) as acceptor. The morphology of the DT-DPP:[70]PCBM blends is characterized by a semicrystalline fibrillar microstructure with fibril widths between 4.5 and 30 nm as evidenced from transmission electron microscopy. A clear correlation is found between the widths of the fibrils and the EQE for photon to electron conversion. The highest EQEs (60%) and power conversion efficiencies (7.1%) are obtained for polymers with fibril widths less than 12 nm. For blends with fibrils wider than 12 nm, the EQE is low because exciton diffusion becomes limiting for charge generation. Interestingly, the correlation found here matches with previous data on related DPP-based polymers. This suggests that for this class of materials the relation between fiber width and EQE is universal. The fiber width is largely correlated with the solubility of the polymers, with less soluble DPP-based polymers giving narrower fibrils.

The influence of siloxane side-chains on the photovoltaic performance of a conjugated polymer.

The effect of gradually replacing the branched alkyl side chains of a diketopyrrolopyrrole (DPP) conjugated polymer by linear side chains containing branched siloxane end groups on the photovoltaic performance of blends of these polymers with a common fullerene acceptor is investigated. With an increasing proportion of siloxane side chains, the molecular weight and solubility of the polymers decreases. While the siloxane containing polymers exhibit a higher hole mobility in field-effect transistors, their performance in solar cells is less than the polymer with only alkyl sides chains. Using grazing-incidence wide-angle X-ray scattering, transmission electron microscopy, and fluorescence spectroscopy we identify two main reasons for the reduced performance of siloxane containing polymers in solar cells. The first one is a somewhat coarser phase-separated morphology with slightly wider polymer fibers. This is unexpected as often the fiber width is inversely correlated with polymer solubility. The second one is stronger non-radiative decay of the pristine polymers containing siloxane side chains.

Efficient Thick-Film Polymer Solar Cells with Enhanced Fill Factors via Increased Fullerene Loading.

Developing effective methods to make efficient bulk-heterojunction polymer solar cells at roll-to-roll relevant active layer thickness is of significant importance. We investigate the effect of fullerene content in polymer:fullerene blends on the fill factor (FF) and on the performance of thick-film solar cells for four different donor polymers PTB7-Th, PDPP-TPT, BDT-FBT-2T, and poly[5,5'-bis(2-butyloctyl)-(2,2'-bithiophene)-4,4'-dicarboxylate- alt-5,5'-2,2'-bithiophene] (PDCBT). At a few hundreds of nanometers thickness, increased FFs are observed in all cases and improved overall device performances are obtained except for PDCBT upon increasing fullerene content in blend films. This fullerene content effect was studied in more detail by electrical and morphological characterization. The results suggest enhanced electron mobility and suppressed bimolecular recombination upon increasing fullerene content in thick polymer:fullerene blend films, which are the result of larger fullerene aggregates and improved interconnectivity of the fullerene phases that provide continuous percolating pathways for electron transport in thick films. These findings are important because an effective and straightforward method that enables fabricating efficient thick-film polymer solar cells is desirable for large-scale manufacturing via roll-to-roll processing and for multijunction devices.

Quadruple Junction Polymer Solar Cells with Four Complementary Absorber Layers.

A monolithic two-terminal solution-processed quadruple junction polymer solar cell in an n-i-p (inverted) configuration with four complementary polymer:fullerene active bulk-heterojunction layers is presented. The subcells possess different optical bandgaps ranging from 1.90 to 1.13 eV. Optical modeling using the transfer matrix formalism enables prediction of the fraction of absorbed photons from sunlight in each subcell and determine the optimal combination of layer thicknesses. The quadruple junction cell features an open-circuit voltage of 2.45 V and has a power conversion efficiency of 7.6%, only slightly less than the modeled value of 8.2%. The external quantum efficiency spectrum, determined with appropriate light and voltage bias conditions, exhibits in general an excellent agreement with modeled spectrum. The device performance is presently limited by bimolecular recombination, which prevents using thick photoactive layers that could absorb light more efficiently.

High-Performance Oligomeric Catholytes for Effective Macromolecular Separation in Nonaqueous Redox Flow Batteries.

Nonaqueous redox flow batteries (NRFBs) represent an attractive technology for energy storage from intermittent renewable sources. In these batteries, electrical energy is stored in and extracted from electrolyte solutions of redox-active molecules (termed catholytes and anolytes) that are passed through an electrochemical flow cell. To avoid battery self-discharge, the anolyte and catholyte solutions must be separated by a membrane in the flow cell. This membrane prevents crossover of the redox active molecules, while simultaneously allowing facile transport of charge-balancing ions. A key unmet challenge for the field is the design of redox-active molecule/membrane pairs that enable effective electrolyte separation while maintaining optimal battery properties. Herein, we demonstrate the development of oligomeric catholytes based on tris(dialkylamino)cyclopropenium (CP) salts that are specifically tailored for pairing with size-exclusion membranes composed of polymers of intrinsic microporosity (PIMs). Systematic studies were conducted to evaluate the impact of oligomer size/structure on properties that are crucial for flow battery performance, including cycling stability, charge capacity, solubility, electron transfer kinetics, and crossover rates. These studies have led to the identification of a CP-derived tetramer in which these properties are all comparable, or significantly improved, relative to the monomeric counterpart. Finally, a proof-of-concept flow battery is demonstrated by pairing this tetrameric catholyte with a PIM membrane. After 6 days of cycling, no crossover is detected, demonstrating the promise of this approach. These studies provide a template for the future design of other redox-active oligomers for this application.

A regioregular terpolymer comprising two electron-deficient and one electron-rich unit for ultra small band gap solar cells.

A regioregular terpolymer that combines electron-deficient diketopyrrolopyrrole and benzothiadiazole units with an electron-rich dithienopyrrole unit is presented. In solar cells, the terpolymer affords an open circuit voltage of 0.52 V and a power conversion efficiency of 3.7% with a spectral response up to 1050 nm.

Wide band gap diketopyrrolopyrrole-based conjugated polymers incorporating biphenyl units applied in polymer solar cells.

Incorporating biphenyls as co-monomers in electron-deficient diketopyrrolopyrrole (DPP) conjugated polymers enables widening the optical band gap to 1.70 eV. Power conversion efficiencies of 3.7-5.7% and high open-circuit voltages of 0.80-0.93 V are obtained in solar cells based on these wide band gap DPP polymers.

Effect of the fibrillar microstructure on the efficiency of high molecular weight diketopyrrolopyrrole-based polymer solar cells.

The nature of the solubilizing alkyl side chains has a strong effect on the performance of semiconducting diketopyrrolopyrrole polymers in organic solar cells with fullerene acceptors. The effect relates to the width of semicrystalline polymer fibrils that form in these blends. If the width of the fibril is wider than the exciton diffusion length, fewer charges form and the efficiency drops.

Efficient small bandgap polymer solar cells with high fill factors for 300 nm thick films.

A high-molecular-weight conjugated polymer based on alternating electron-rich and electron-deficient fused ring systems provides efficient polymer solar cells when blended with C60 and C70 fullerene derivatives. The morphology of the new polymer/fullerene blend reduces bimolecular recombination and allows reaching high fill factors and power conversion efficiencies for films up to 300 nm thickness.