Design and Evaluation of a Knee Flexion Assistance Exoskeleton for People with Transtibial Amputation.

People with below-knee amputation walk with asymmetric gaits that over time can lead to further musculoskeletal disorders and decreased quality of life. While prosthesis technology is improving, prosthetic ankles may be fundamentally limited in their ability to restore healthy walking patterns because they do not assist the residual knee joint. The knee on the residual limb has muscular deficits due to the loss of the gastrocnemius, a biarticular muscle that crosses both the ankle and knee. Here we present the design, development, and preliminary evaluation of a robotic knee exoskeleton for people with transtibial amputation. The device is intended to restore gastrocnemius-like flexion moments to the knee on the residual limb. The exoskeleton uses a custom offboard actuation and control system to allow for a simple and lightweight design with high torque capabilities. A preliminary walking experiment with one person with transtibial amputation was conducted. The exoskeleton provided a range of knee flexion torque profiles and had an RMS tracking error of 1.9 Nm across four assistance conditions. This device will be used in future studies to explore the effects of providing knee flexion assistance to people with transtibial amputation during walking. Long term, findings from studies with this exoskeleton could motivate future assistive device designs that improve walking mechanics and quality of life for people with limb loss.

Evaluation of novel plantar pressure-based 3-dimensional printed accommodative insoles - A feasibility study.

BACKGROUND: Custom insoles are commonly prescribed to patients with diabetes to redistribute plantar pressure and decrease the risk of ulceration. Advances in 3D printing have enabled the creation of 3D-printed personalized metamaterials whose properties are derived not only from the base material but also the lattice microstructures within the metamaterial. Insoles manufactured using personalized metamaterials have both patient-specific geometry and stiffnesses. However, the safety and biomechanical effect of the novel insoles have not yet been tested clinically. METHODS: Individuals without ulcer, neuropathy, or deformity were recruited for this study. In-shoe walking plantar pressure at baseline visit was taken and sensels with pressure over 200 kPa was used to define offloading region(s). Three pairs of custom insoles (two 3D printed insoles with personalized metamaterials (Hybrid and Full) designed based on foot shape and plantar pressure mapping and one standard-of-care diabetic insole as a comparator). In-shoe plantar pressure measurements during walking were recorded in a standardized research shoe and the three insoles and compared across all four conditions. FINDINGS: Twelve individuals were included in the final analysis. No adverse events occurred during testing. Maximum peak plantar pressure and the pressure time integral were reduced in the offloading regions in the Hybrid and Full but not in the standard-of-care compared to the research shoe. INTERPRETATION: This feasibility study confirms our ability to manufacture the 3D printed personalized metamaterials insoles and demonstrates their ability to reduce plantar pressure. We have demonstrated the ability to modify the 3D printed design to offload certain parts of the foot using plantar pressure data and a patient-specific metamaterials in the 3D printed insole design. The advance in 3D printed technology has shown its potential to improve current care.

A novel workflow to fabricate a patient-specific 3D printed accommodative foot orthosis with personalized latticed metamaterial.

Patients with diabetes mellitus are at elevated risk for secondary complications that result in lower extremity amputations. Standard of care to prevent these complications involves prescribing custom accommodative insoles that use inefficient and outdated fabrication processes including milling and hand carving. A new thrust of custom 3D printed insoles has shown promise in producing corrective insoles but has not explored accommodative diabetic insoles. Our novel contribution is a metamaterial design application that allows the insole stiffness to vary regionally following patient-specific plantar pressure measurements. We presented a novel workflow to fabricate custom 3D printed elastomeric insoles, a testing method to evaluate the durability, shear stiffness, and compressive stiffness of insole material samples, and a case study to demonstrate how the novel 3D printed insoles performed clinically. Our 3D printed insoles results showed a matched or improved durability, a reduced shear stiffness, and a reduction in plantar pressure in clinical case study compared to standard of care insoles.