Mitigation of transverse mode instability by heat-load modulation.

We present the first experimental realization of a new mitigation strategy for TMI based on controlling the phase shift between the modal intensity pattern and the thermally induced refractive index grating. If specific modulation parameters are applied while pulsing the seed and/or pump radiation, the direction of energy transfer is forced from the higher-order modes into the fundamental mode. In this way, the fiber amplifier can operate at an average output power significantly higher than the TMI threshold with a diffraction-limited beam profile. A stable beam profile is observed at an average output power that is 83% higher than the TMI threshold of the free-running system, with an intra-burst average power that is 4.15 times higher than the TMI threshold.

Characterization of transverse mode instability with a 4-quadrant photodiode.

Transverse mode instability (TMI) represents the main limitation for the power scaling of fiber laser systems with a diffraction-limited beam quality. In this context, it has become increasingly important to find a cheap and reliable way to monitor and characterize TMI and distinguish this effect from other dynamic perturbations. In this work, with the help of a position-sensitive detector, a novel method is developed to characterize the TMI dynamics even in the presence of power fluctuations. The position information of the fluctuating beam is recorded in the X- and Y-axis of the detector, which are used to track the temporal evolution of the center of gravity of the beam. The trajectories described by the beam within a specific time window contain rich information about TMI, which can be used to gain further insight into this phenomenon.

Analysis of optical core-to-core coupling: challenges and opportunities in multicore fiber amplifiers.

In this work we study in detail core-to-core coupling effects in multicore fibers (MCFs) using a simulation tool based on supermodal interference. We pay particular attention to the impact of core area scaling, which plays an important role in prospective amplifier systems. We consider geometrical and optical properties of the MCF structure, including the ability for dense packaging of the cores but also the influence on the core guidance (V-parameter). In general, this study is important to unlock the power and energy scaling potential of the next-generation MCF amplifiers.

TMI and polarization static energy transfer in Yb-doped low-NA PM fibers.

In this work, we conduct experimental investigations of transverse mode instabilities (TMI) in a large mode area ultra-low numerical aperture polarization maintaining fiber amplifier. This fiber is few mode in the slow-axis (conventional operation mode), but single mode in the fast-axis. We test the stability of the output beam by changing the input polarization angle and systematically investigate the transverse mode instability threshold in the two principal polarization axes. The lowest TMI threshold at 300 W was found when the input polarization angle was aligned parallel to the slow-axis. Detuning the input polarization angle from the slow-axis led to increased TMI thresholds. For input polarization angle of 90° (parallel to the fast-axis), the output signal was stable up to 475 W and further scaling was limited by the available pump power. However, for fast-axis operation a lower polarization ratio compared to slow-axis operation was observed as well as an unexpected static energy transfer from the fast-axis into the slow-axis above 400 W.

Mitigation of transverse mode instability by modal birefringence in polarization-maintaining fibers.

The effect of transverse mode instability (TMI) poses a fundamental obstacle for a further scaling of diffraction-limited, high-power fiber laser systems. In this work we present a theoretical and experimental study on the mitigation of TMI by modal birefringence in a polarization maintaining (PM) fiber. With the help of comprehensive simulations, we show that the thermally-induced refractive index grating responsible for TMI can be modified and washed out when light is coupled with a polarization input angle detuned from the main axes of the fiber. To confirm the theoretical predictions, we have designed and manufactured an Yb-doped large-mode-area PM fiber. Using this fiber, we have systematically investigated the dependence of the TMI threshold on the polarization input angle of the seed laser. We experimentally demonstrate that when the polarization input angle of the seed is aligned at 50° with respect to the slow-axis, the TMI threshold increases by a factor of 2, verifying the theory and the numerical simulations. A high speed polarization mode-resolved analysis of the output beam is presented, which reveals that at the onset of TMI both polarization axes fluctuates simultaneously.

Temperature-dependent cross section spectra for thulium-doped fiber lasers.

An investigation on the temperature dependence of spectroscopic parameters of trivalent thulium ions is important for the design of high-power, thulium-doped fiber lasers and amplifiers. In this Letter, the thulium absorption/emission cross sections are determined in the spectral range 700-2200 nm and in the temperature range from -196°C to 300°C. The spectra are obtained from the absorption and emission measurements of a thulium-doped fiber and from measured thulium concentration profiles. Attempts were made to estimate the temperature dependence of the spectra where the measurements are not accessible. Firstly, the spectra are fitted to a multi-Gaussian model with temperature dependent parameters. Secondly, a physically motivated model of the cross section spectra is proposed and analyzed.

High-power two-color plasma-based THz generation driven by a Tm-doped fiber laser.

We report on the efficient generation of broadband THz radiation based on a two-color gas-plasma scheme. Broadband THz pulses covering the whole THz spectral region, from 0.1-35 THz, are generated. This is enabled by a high-power, ultra-fast, thulium-doped, fiber chirped pulse amplification (Tm:FCPA) system and a subsequent nonlinear pulse compression stage that uses a gas-filled capillary. The driving source delivers 40 fs pulses at a central wavelength of 1.9 µm with 1.2 mJ pulse energy and 101 kHz repetition rate. Owing to the long driving wavelength and the use of a gas-jet in the THz generation focus, the highest reported conversion efficiency for high-power THz sources (>20 mW) of 0.32% has been achieved. The high efficiency and average power of 380 mW of the broadband THz radiation make this an ideal source for nonlinear, tabletop THz science.

Nonlinear pulse compression to sub-two-cycle, 1.3†mJ pulses at 1.9†µm wavelength with 132†W average power.

We report the nonlinear pulse compression of a high-power, thulium-doped fiber laser system using a gas-filled hollow-core fiber. The sub-two cycle source delivers 1.3 mJ pulse energy with 80 GW peak power at a central wavelength of 1.87 µm and an average power of 132 W. This is, so far, to the best of our knowledge, the highest average power of a few-cycle laser source reported in the short-wave infrared region. Given its unique combination of high pulse energy and high average power, this laser source is an excellent driver for nonlinear frequency conversion, toward terahertz, mid-infrared, and soft X-ray spectral regions.

Frequency-doubled Q-switched 4 × 4 multicore fiber laser system.

Frequency doubling of a Q-switched Yb-doped rod-type 4 × 4 multicore fiber (MCF) laser system is reported. A second harmonic generation (SHG) efficiency of up to 52% was achieved with type I non-critically phase-matched lithium triborate (LBO), with a total SHG pulse energy of up to 17 mJ obtained at 1 kHz repetition rate. The dense parallel arrangement of amplifying cores into a shared pump cladding enables a significant increase in the energy capacity of active fibers. The frequency-doubled MCF architecture is compatible with high-repetition-rate and high-average-power operation and may provide an efficient alternative to bulk solid-state systems as pump sources for high-energy titanium-doped sapphire lasers.

Mitigation of thermally-induced performance limitations in coherently-combined multicore fiber amplifiers.

Multicore fiber (MCF) amplifiers have gained increasing interest over the past years and shown their huge potential in first experiments. However, high thermal loads can be expected when operating such an amplifier at its limit. Especially in short MCF amplifiers that are pumped in counter-propagation, this leads to non-uniform mode-shrinking in the cores and, consequently, to a degradation of the system performance. In this work we show different ways to counteract the performance limitations induced by thermal effects in coherently-combined, multicore fiber amplifiers. First, we will show that pumping MCFs in co-propagation will significantly improve the combinable average power since the thermal load at the fiber end is reduced. However, this approach might not be favorable for high energy extraction. Therefore, we will introduce a new MCF design pumped in counter-propagation that leads to a reduction of the thermal load at the fiber end, which will allow for both high combined output power and pulse energy.

Inband-pumped, high-power thulium-doped fiber amplifiers for an ultrafast pulsed operation.

We investigate the influence of the pump wavelength on the high-power amplification of large-mode area, thulium-doped fibers which are suitable for an ultrashort pulsed operation in the 2 µm wavelength region. By pumping a standard, commercially available photonic crystal fiber in an amplifier configuration at 1692 nm, a slope efficiency of 80 % at an average output power of 60 W could be shown. With the help of simulations we investigate the effect of cross-relaxations on the efficiency and the thermal behavior. We extend our investigations to a rod-type, large-pitch fiber with very large mode area, which is exceptionally suited for high-energy ultrafast operation. Pumping at 1692 nm leads to a slope efficiency of 74 % with a average output power of 67 W, instead of the 38 % slope efficiency obtained when pumping at 793 nm. These results pave the way to highly efficient 2 µm fiber-based CPA systems.

High-energy Q-switched 16-core tapered rod-type fiber laser system.

High-energy Q-switched master oscillator power amplifier systems based on rod-type 4 × 4 multicore fibers are demonstrated, achieving energy up to 49 mJ in ns-class pulses. A tapered fiber geometry is tested that maintains low mode order in large multimode output cores, improving beam quality in comparison to a similar fiber with no taper. The tapered fiber design can be scaled both in the number of amplifying cores and in the dimensions of the cores themselves, providing a potential route toward joule-class fiber lasers systems.

500†W rod-type 4 × 4 multicore ultrafast fiber laser.

We present a coherently combined femtosecond fiber chirped-pulse-amplification system based on a rod-type, ytterbium-doped, multicore fiber with 4 × 4 cores. A high average power of up to 500 W (after combination and compression) could be achieved at 10 MHz repetition rate with excellent beam quality. Additionally, < 500 fs pulses with up to 600 µJ of pulse energy were also realized with this setup. This architecture is intrinsically power scalable by increasing the number of cores in the fiber.

Control and stabilization of the modal content of fiber amplifiers using traveling waves.

In this work we present a novel way to manipulate the effect of transverse mode instability by inducing traveling waves in a high-power fiber system. What sets this technique apart is the fact that it allows controlling the direction of the modal energy flow, for the first time to the best of our knowledge. Thus, using the method proposed in this work it will be possible to transfer energy from the higher-order mode into the fundamental mode of the fiber, which mitigates the effect of transverse mode instability, but also to transfer energy from the fundamental mode into the higher-order mode. Our simulations indicate that this approach will work both below and above the threshold of transverse mode instability. In fact, our model reveals that it can be used to force a nearly pure fundamental mode output in the fiber laser system almost independently of the input coupling conditions. In this context, this technique represents the first attempt to exploit the physics behind the effect of transverse mode instability to increase the performance of fiber laser systems.

Transverse mode instability and thermal effects in thulium-doped fiber amplifiers under high thermal loads.

We experimentally analyze the average-power-scaling capabilities of ultrafast, thulium-doped fiber amplifiers. It has been theoretically predicted that thulium-doped fiber laser systems, with an emission wavelength around 2 µm, should be able to withstand much higher heat-loads than their Yb-doped counterparts before the onset of transverse mode instability (TMI) is observed. In this work we experimentally verify this theoretical prediction by operating thulium doped fibers at very high heat-load. In separate experiments we analyze the performance of two different large-core, thulium-doped fiber amplifiers. The first experiment aims at operating a short, very-large core, thulium-doped fiber amplifier at extreme heat-load levels of more than 300 W/m. Even at this extreme heat-load level, the onset of TMI is not observed. The second experiment maximizes the extractable average-output power from a large-core, thulium-doped, fiber amplifier. We have achieved a pump-limited average output power of 1.15 kW without the onset of TMI. However, during a longer period of operation at this power level the amplifier performance steadily degraded and TMI could be observed for average powers in excess of 847 W thereafter. This is the first time, to the best of our knowledge, that TMI has been reported in a thulium-doped fiber amplifier.

Experimental analysis of Raman-induced transverse mode instability in a core-pumped Raman fiber amplifier.

The effect of transverse mode instability is a limitation for the power scaling of fiber laser systems, that can originate due to heat caused by stimulated Raman scattering. In this contribution, we experimentally investigate the threshold of transverse mode instability caused by stimulated Raman scattering in a passive fiber. Both, the Stokes seed power and the fiber length of a core-pumped Raman fiber amplifier are varied to systematically study this effect. Mode resolved measurements reveal that the threshold occurs at approximately the same Stokes output power for all tested configurations, independent of the total Raman conversion efficiency. These results increase the understanding of this type of mode instability and show which parameters are important for a further power scaling of high-power Raman fiber amplifiers.

Gas-plasma-based generation of broadband terahertz radiation with 640 mW average power.

We present a high-power source of broadband terahertz (THz) radiation covering the whole THz spectral region (0.1-30 THz). The two-color gas plasma generation process is driven by a state-of-the-art ytterbium fiber chirped pulse amplification system based on coherent combination of 16 rod-type amplifiers. Prior to the THz generation, the pulses are spectrally broadened in a multipass cell and compressed to 37 fs with a pulse energy of 1.3 mJ at a repetition rate of 500 kHz. A gas-jet scheme has been employed for the THz generation, increasing the efficiency of the process to 0.1%. The air-biased coherent detection scheme is implemented to characterize the full bandwidth of the generated radiation. A THz average power of 640 mW is generated, which is the highest THz average power achieved to date. This makes this source suitable for a variety of applications, e.g., spectroscopy of strongly absorbing samples or driving nonlinear effects for the studies of material properties.

Simplified design of optical elements for filled-aperture coherent beam combination.

A simplification strategy for segmented mirror splitters (SMS) used as beam combiners is presented. These devices are useful for compact beam division and the combination of linear and 2-D arrays. However, the standard design requires unique thin-film coating sections for each input beam; thus, potential for scaling to high beam-counts is limited due to manufacturing complexity. Taking advantage of the relative insensitivity of the beam combination process to amplitude variations, numerical techniques are used to optimize highly simplified designs with only one, two or three unique coatings. It is demonstrated that with correctly chosen coating reflectivities, the simplified optics are capable of high combination efficiency for several tens of beams. The performance of these optics as beam splitters in multicore fiber amplifier systems is analyzed, and inhomogeneous power distribution of the simplified designs is noted as a potential source of combining loss in such systems. These simplified designs may facilitate further scaling of filled-aperture coherently combined systems in linear array or 2-D array formats.

Impact of thermo-optical effects in coherently combined multicore fiber amplifiers.

In this work we analyze the power scaling potential of amplifying multicore fibers (MCFs) used in coherently combined systems. In particular, in this study we exemplarily consider rod-type MCFs with 2 × 2 up to 10 × 10 ytterbium-doped cores arranged in a squared pattern. We will show that, even though increasing the number of active cores will lead to higher output powers, particular attention has to be paid to arising thermal effects, which potentially degrade the performance of these systems. Additionally, we analyze the influence of the core dimensions on the extractable and combinable output power and pulse energy. This includes a detailed study on the thermal effects that influence the propagating transverse modes and, in turn, the amplification efficiency, the combining efficiency, the onset of nonlinear effect, as well as differences in the optical path lengths between the cores. Considering all these effects under rather extreme conditions, the study predicts that average output powers higher than 10 kW from a single 1 m long ytterbium-doped MCF are feasible and femtosecond pulses with energies higher than 400 mJ can be extracted and efficiently recombined in a filled-aperture scheme.

Fiber laser-driven gas plasma-based generation of THz radiation with 50-mW average power.

We present on THz generation in the two-color gas plasma scheme driven by a high-power, ultrafast fiber laser system. The applied scheme is a promising approach for scaling the THz average power but it has been limited so far by the driving lasers to repetition rates up to 1 kHz. Here, we demonstrate recent results of THz generation operating at a two orders of magnitude higher repetition rate. This results in a unprecedented THz average power of 50 mW. The development of compact, table-top THz sources with high repetition rate and high field strength is crucial for studying nonlinear responses of materials, particle acceleration or faster data acquisition in imaging and spectroscopy.