Accessible interferometric autocorrelator for noise-like pulses based on a Fabry-Perot cavity.

In this work, we develop experimentally a Fabry-Perot fiber optic interferometer applied to the measurement of autocorrelation of complex dynamic pulses generated by a figure-eight fiber laser. The principle is based in the superposition of multiple pulses, which requires two partially reflecting flat surfaces in parallel, resulting in a simple and compact autocorrelator design. The autocorrelation trace obtained exhibits a typical double-scaled structure for noise-like pulses (NLPs), with an ultrashort coherence spur on the order of 100 fs riding upon a broad pedestal of 120 ps. Finally, we show experimentally that the developed Fabry-Perot device is able to measure accurately the autocorrelation of NLPs, as confirmed by comparing the measurement with that of a conventional autocorrelator scheme based on a Michelson interferometer, with the additional advantages of a more compact setup and a much easier alignment procedure compared to the latter.

High energy noise-like pulsing in a double-clad Er/Yb figure-of-eight fiber laser.

In this work, we study a 215-m-long figure-of-eight fiber laser including a double-clad erbium-ytterbium fiber and a nonlinear optical loop mirror based on nonlinear polarization evolution. For proper adjustments, self-starting passive mode-locking is obtained. Measurements show that the mode-locked pulses actually are noise-like pulses, by analyzing the autocorrelation, scope traces and the very broad and flat spectrum extending over a record bandwidth of more than 200 nm, beyond the 1750 nm upper wavelength limit of the optical spectrum analyzer. Noise-like pulsing was observed for moderate and high pump power preserving the same behavior, reaching pulse energies as high as 300 nJ, with pulse durations of a few tens of ns and a coherence length in the order of 1 ps. Stable fundamental mode locking as well as harmonic mode locking up to the 6th order were observed. The bandwidth was further extended to more than 450 nm when a 100-m piece of highly nonlinear fiber was inserted at the laser output. The enhanced performances obtained compared to other similar schemes could be related to the absence of a polarizer in the present setup, so that the state of polarization along the cavity is no longer restricted.

Plasma-based optical fiber tapering rig.

Optical fiber tapers have been widely proposed and demonstrated as reliable optical fiber structures for sensing, lasers, and supercontinuum generation applications. This paper proposes an innovative approach to fabricating optical fiber tapers using plasma as the heat source. From our literature review, and to the best of our knowledge, this is the first time that plasma has been used as the heat source for producing optical fiber tapers. The system is not intricate and simple to replicate. Moreover, the elements involved make this machine attractive to research groups devoted to optical fibers. The setup consistently generates robust biconical optical fiber tapers. A typical waist of ∼8 µm and taper lengths ranging from 3 to 15 mm are achieved. Our results showed tapers with interference fringes up to 12 dB, from 1465 nm to 1599 nm. Furthermore, the statistical evaluation presented demonstrates a good level of reproducibility in our tapering process.

Low-pressure and liquid level fiber-optic sensor based on polymeric Fabry-Perot cavity.

An experimental study of the interaction between a Mylar® polymer film and a multimode fiber-optic is presented for the simultaneous fiber-optic detection of low-pressure and liquid levels. The junction between the polymer and optical fiber produces an interference spectrum with maximal visibility and free spectral range around 9 dB and 31 nm, respectively. Water pressure, which is controlled by the liquid level, stresses the polymer. As a result, the spectrum wavelength shifts to the blue region, achieving high sensitivities around 2.49 nm/kPa and 24.5 nm/m. The polymeric membrane was analyzed using a finite element model; according to the results, the polymer shows linear stress response. Furthermore, the membrane material is operated below the yielding point. Moreover, the finite analysis provides information about the stress effect over the thickness and the birefringence changes. This sensor exhibits a quadratic polynomial fitting with an adjusted R-squared of 0.9539. The proposed sensing setup offers a cost-effective alternative for liquid level and low-pressure detection.