Evaluation of GC-EI&CI-TOFMS for Nontarget Analysis of Industrial Wastewater Using Hydrophilic-Lipophilic-Balanced SPME.

The evaluation of nontarget analysis (NTA) techniques for the monitoring of wastewater is important as wastewater is an anthropogenic pollution source for aquatic ecosystems and a threat to human and environmental health. This study presents the proof-of-concept NTA of industrial wastewater samples. A prototype hydrophilic-lipophilic-balanced (HLB) SPME and gas chromatography interfaced with time-of-flight high-resolution mass spectrometry (GC-TOFMS) with electron ionization (EI) and chemical ionization (CI) in parallel are employed. The HLB-SPME consists of a poly(divinylbenzene-co-N-vinylpyrrolidone) structure, allowing the extraction of hydrophilic as well as lipophilic substances. As the combination of parallel CI and EI data provides a comprehensive data set as a unique feature, this study is strongly focused on the compound identification procedure and confidence reporting of exemplary substances. Furthermore, the use of three different CI reagent ions, including [N2H]+/[N4H]+, [H3O]+, and [NH4]+, enables a broad range of analytes to be ionized in terms of selectivity and softness. The complementary information provided by EI and CI data allows a level 3 identification or higher in 69% of cases. The polarity coverage based on the physicochemical properties of the analytes (such as volatility, water solubility, hydrophilicity, and lipophilicity) was visualized by using Henry's law and octanol-water partitioning constants. In conclusion, the presented approach is shown to be valuable for water analysis and allows enhanced and accelerated compound identification compared to utilizing only one type of ionization.

Isotope-labeling in situ derivatization and HS-SPME arrow GC-MS/MS for simultaneous determination of fatty acids and fatty acid methyl esters in aqueous matrices.

Fatty acids (FAs) and fatty acid methyl esters (FAMEs) co-occur in many samples, and analysis of both substance classes is frequently of high interest. To this end, this study introduces the first method for simultaneous determination of FAs and FAMEs including fully automated solvent-free solid-phase microextraction (SPME) arrow headspace extraction combined with isotope-labeling in situ FA derivatization with deuterated methanol (CD3OD). By using the chromatographic isotope effect (ΔRt = 0.03 min) and the + 3 m/z mass shift, FAs can be selectively differentiated from the FAMEs during gas chromatography tandem-mass spectrometry (GC-MS/MS) operated in the multiple reaction monitoring (MRM) aquisition mode. Additionally, an approach is presented to predict the retention times of deuterated compounds. Optimization of the derivatization conditions was accomplished by design of experiments and found to be 20 min, 50 °C, 4 v/v% CD3OD, and pH 2.1. During method validation, FAs and FAMEs were calibrated in different concentration ranges by standard addition in five real matrices and ultrapure water leading to good linearities and method detection limits for FAs ranging from 1-30 µg L-1 and for FAMEs from 0.003-0.72 µg L-1. FAs and FAMEs were detected in real samples from surface water, wastewater treatment plant effluent, and three different bioreactor samples and could be quantified in concentrations ranging from 2-1056 µg L-1 for FAs and 0.01-14 µg L-1 for FAMEs.

How to Couple LC-IRMS with HRMS─A Proof-of-Concept Study.

Compound-specific stable isotope analysis (CSIA) is a unique analytical technique for determining small variations in isotope ratios of light isotopes in analytes from complex mixtures. A problem of CSIA using gas chromatography (GC) and liquid chromatography-isotope ratio mass spectrometry (LC-IRMS) is that any structural information of the analytes is lost due to the processes involved in determining the isotope ratio. To obtain the isotopic composition of, for example, carbon from organic compounds, all carbon in each analyte is quantitatively converted to CO2. For GC-IRMS, open split GC-IRMS-MS couplings have been described that allow additional acquisition of structural information of analytes and interferences. Structural analysis using LC-IRMS is more difficult and requires additional technical and instrumental efforts. In this study, LC was combined for the first time with simultaneous analysis by IRMS and high-resolution mass spectrometry (HRMS), enabling the direct identification of unknown or coeluting species. We have thoroughly investigated and optimized the coupling and showed how technical problems, arising from instrumental conditions, can be overcome. To this end, it was successfully demonstrated that a consistent split ratio between IRMS and HRMS could be obtained using a variable postcolumn flow splitter. This coupling provided reproducible results in terms of resulting peak areas, isotope values, and retention time differences for the two mass spectrometer systems. To demonstrate the applicability of the coupling, we chose to address an important question regarding the purity of international isotope standards. In this context, we were able to confirm that the USGS41 reference material indeed contains substantial amounts of pyroglutamic acid as suggested previously in the literature. Moreover, the replacement material, USGS41a, still has significant amounts of pyroglutamic acid as impurity, rendering some caution necessary when using this material for isotopic calibration.

Two Pathways Compete in the Mn(II)-Catalyzed Oxidation of Aminotrismethylene Phosphonate (ATMP).

Mn(II)-catalyzed oxidation by molecular oxygen is considered a relevant process for the environmental fate of aminopolyphosphonate chelating agents such as aminotrismethylene phosphonate (ATMP). However, the potential roles of Mn(III)ATMP-species in the underlying transformation mechanisms are not fully understood. We combined kinetic studies, compound-specific stable carbon isotope analysis, and equilibrium speciation modeling to shed light on the significance of such Mn-ATMP species for the overall ATMP oxidation by molecular oxygen. The fraction of ATMP complexed with Mn(II) inversely correlated with both (i) the Mn(II)-normalized transformation rate constants of ATMP and (ii) the observed carbon isotope enrichment factors (εc-values). These findings provide evidence for two parallel ATMP transformation pathways exhibiting distinctly different reaction kinetics and carbon isotope fractionation: (i) oxidation of ATMP present in Mn(III)ATMP complexes (εc ≈ -10 ‰) and (ii) oxidation of free ATMP by such Mn(III)ATMP species (εc ≈ -1 ‰) in a catalytic cycle. The higher reaction rate of the latter pathway implies that aminopolyphosphonates can be trapped in catalytic Mn-complexes before being transformed and suggests that Mn(III)ATMP might be a potent oxidant also for other reducible solutes in aqueous environments.

Optimization and automation of rapid and selective analysis of fatty acid methyl esters from aqueous samples by headspace SPME arrow extraction followed by GC-MS/MS analysis.

The analysis of fatty acid methyl esters (FAMEs) is of high relevance for monitoring and control of various industrial processes and biological systems. In this study, a novel, green analytical approach for the determination of 24 FAMEs from aqueous samples is proposed, which is based on a headspace solid-phase microextraction (SPME) arrow followed by gas chromatography coupled to tandem mass spectrometry (GC-MS/MS). The method was substantially accelerated to a run time of 44 min per sample by thorough optimization and automation of the relevant parameters. The limiting parameters, mostly based on expediting equilibrium attainment, were found to be parameters of extraction: material, pH, time, and temperature, which were optimized to divinylbenzene polydimethylsiloxane (DVB-PDMS), pH 2, 20 min, and 70 °C, respectively. The optimization and automation of the method led to low method detection limits (9-437 ng L-1) and high selectivity. Evaluation of the method on real samples was done by analyzing the aqueous phase of a bioreactor, whereby the matrix effect could be greatly reduced due to dilution and headspace sampling. The rapid, sensitive, selective, and matrix-reduced approach is found to be not only a novel method for water analysis but is promising for further applications, e.g., with solid and gaseous samples containing FAMEs.

Carbon Isotope Fractionation of Substituted Benzene Analogs during Oxidation with Ozone and Hydroxyl Radicals: How Should Experimental Data Be Interpreted?

Oxidative processes frequently contribute to organic pollutant degradation in natural and engineered systems, such as during the remediation of contaminated sites and in water treatment processes. Because a systematic characterization of abiotic reactions of organic pollutants with oxidants such as ozone or hydroxyl radicals by compound-specific stable isotope analysis (CSIA) is lacking, stable isotope-based approaches have rarely been applied for the elucidation of mechanisms of such transformations. Here, we investigated the carbon isotope fractionation associated with the oxidation of benzene and several methylated and methoxylated analogs, namely, toluene, three xylene isomers, mesitylene, and anisole, and determined their carbon isotope enrichments factors (εC) for reactions with ozone (εC = -3.6 to -4.6 ‰) and hydroxyl radicals (εC = 0.0 to -1.2‰). The differences in isotope fractionation can be used to elucidate the contribution of the reactions with ozone or hydroxyl radicals to overall transformation. Derivation of apparent kinetic isotope effects (AKIEs) for the reaction with ozone, however, was nontrivial due to challenges in assigning reactive positions in the probe compounds for the monodentate attack leading to an ozone adduct. We present several options for this step and compare the outcome to quantum chemical characterizations of ozone adducts. Our data show that a general assignment of reactive positions for reactions of ozone with aromatic carbons in ortho-, meta-, or para-positions is not feasible and that AKIEs of this reaction should be derived on a compound-by-compound basis.

Stable carbon isotope analysis of polyphosphonate complexing agents by anion chromatography coupled to isotope ratio mass spectrometry: method development and application.

Compound-specific carbon isotope analysis (carbon CSIA) by liquid chromatography/isotope ratio mass spectrometry (LC-IRMS) is a novel and promising tool to elucidate the environmental fate of polar organic compounds such as polyphosphonates, strong complexing agents for di- and trivalent cations with growing commercial importance over the last decades. Here, we present a LC-IRMS method for the three widely used polyphosphonates 1-hydroxyethane 1,1-diphosphonate (HEDP), amino tris(methylenephosphonate) (ATMP), and ethylenediamine tetra(methylenephosphonate) (EDTMP). Separation of the analytes, as well as ATMP and its degradation products, was carried out on an anion exchange column under acidic conditions. Quantitative wet chemical oxidation inside the LC-IRMS interface to CO2 was achieved for all three investigated polyphosphonates at a comparatively low sodium persulfate concentration despite the described resilience of HEDP towards oxidative breakdown. The developed method has proven to be suitable for the determination of carbon isotope fractionation of ATMP transformation due to manganese-catalyzed reaction with molecular oxygen, as well as for equilibrium sorption of ATMP to goethite. A kinetic isotope effect was associated with the investigated reaction pathway, whereas no detectable isotope fractionation could be observed during sorption. Thus, CSIA is an appropriate technique to distinguish between sorption and degradation processes that contribute to a concentration decrease of ATMP in laboratory batch experiments. Our study highlights the potential of carbon CSIA by LC-IRMS to gain a process-based understanding of the fate of polyphosphonate complexing agents in environmental as well as technical systems.

Determination of liquid chromatography/flame ionization detection response factors for N-heterocycles, carboxylic acids, halogenated compounds, and others.

Many gas chromatography-flame ionization detection (GC/FID) studies are dealing with response behavior of analytes such as alcohols and alkanes. Studies in the field of liquid chromatography (LC)/FID mainly focused on volatile analytes. In contrast, studies on LC/FID by conveyor type interface covered high molecular weight non-volatile biopolymers, whereby no response factors were calculated. With this study, we fill the gap and present response factors of volatile and non-volatile analytes by LC/FID in terms of flow injection (FIA) measurements of the single compounds without an analytical separation by an LC column. In the present study, 56 different compounds such as carboxylic acids, N-heterocycles, halogenated acids, pharmaceuticals, and other compounds were investigated. In some cases, the obtained response factor data confirmed aspects known from GC/FID studies. But this study also disproves several assumptions done in previous response studies as well as the prediction models based upon the experimental data and literature. Especially the response factors and effective carbon number (ECN) values of structural isomers such as pyrazine, pyridazine, and pyrimidine are assumed to be equal in current response prediction models. Contradictory to these assumptions, the experimental response factors and ECN values of, e.g., the structural isomers pyrazine (RFExp = 0.59; ECNExp = 3.66), pyridazine (RFExp = 0.66; ECNExp = 4.1), and pyrimidine (RFExp = 0.63; ECNExp = 3.93) reveal different experimental response factors and ECN than proposed by response factor prediction models (RFExp = 0.64; ECNExp = 4). Graphical abstract Graphical abstract.

You are how you eat: differences in trophic position of two parasite species infecting a single host according to stable isotopes.

Parasitism is commonly recognised as a consumer strategy, although, the interaction of parasites in communities and ecosystems are generally poorly understood. As parasites are integral parts of food webs, analysis of the trophic interactions between parasites and hosts was assessed through comparison of stable isotope ratios of carbon (13C/12C) and nitrogen (15N/14N). Largemouth yellowfish (Labeobarbus kimberleyensis) infected with the Asian tapeworm (Schyzocotyle acheilognathi) were collected from the Vaal Dam. Signatures of δ13C and δ15N were assessed in host muscle and liver tissue, and cestodes using an elemental analyser coupled with an isotope ratio-mass spectrometer (EA-IRMS). Hosts were enriched by 4.1‰ in the heavy nitrogen isotope with respect to the S. acheilognathi and therefore occupy a higher trophic position than the parasite. Comparison of δ13C indicates that dietary sources of carbon in cestodes are derived from the host liver. Comparison of stable isotope signatures between Paradiplozoon ichthyoxanthon (another common parasite of the Largemouth yellowfish in the Vaal River) and S. acheilognathi showed that the monogenean was enriched by 5.3‰ in 15N which accounts for a difference of almost two trophic positions. Isotope differences in the host-parasite system considered indicate that differences can be related to the mode of nutrient acquisition employed by host and parasites. Cestodes, being depleted in both 13C and 15N relative to the host and monogenean (P. ichthyoxanthon), indicate that S. acheilognathi assimilates nutrients derived from the host metabolism which are released from the liver.

New Concepts for the Determination of Oxidation Efficiencies in Liquid Chromatography-Isotope Ratio Mass Spectrometry.

In liquid chromatography coupled to isotope ratio mass spectrometry (LC-IRMS), analytes are separated on an LC system and consecutively oxidized to CO2, which is required for the determination of compound-specific carbon isotope ratios. Oxidation is performed in an online reactor by sulfate radicals. Reaction conditions in the interface depend on the flow conditions determined by the LC method and the flow rates and concentrations of oxidation agent and phosphoric acid added in the interface. To determine accurate isotope ratios, a quantitative conversion of the carbon contained in the analyte to the CO2 measurement gas is a prerequisite. Oxidation efficiencies are not commonly evaluated during method development, although certain analytes are known to be difficult to be oxidized by sulfate radicals. For the assessment of the oxidation efficiency of the LC-IRMS system, three different approaches were evaluated. (1) Residual organic carbon in the eluent stream of the interface was determined to calculate oxidation yields depending on the initial analyte concentration. (2) The IRMS response was calibrated to an inorganic carbon reference material to determine oxidation efficiencies with the help of the IRMS as a detector. (3) The oxidation temperature was deliberately reduced while monitoring the δ13C and signal intensity. The common assumption that a linear relation of IRMS signal to analyte concentration is an indicator for complete oxidation in LC-IRMS could be disproved. All three approaches can be applied for future method development in LC-IRMS, monitoring of existing flow injection applications, as well as for verification of complete oxidation in established LC-IRMS methods.

Determination of liquid chromatography/flame ionization detection response factors for alcohols, ketones, and sugars.

In the past, the main focus of flame ionization detector (FID) response studies was set on investigations of gas chromatography (GC) relevant analytes such as aliphatic hydrocarbons and selected functional groups. Only a few data are available for liquid chromatography (LC)/FID responses. Within this research paper, we present the FID response factors for a LC/FID system with an aqueous eluent as mobile phase. The study focus on the most common analytes of LC/FID studies in the past as well as several compounds that are not directly GC compatible because of their polarity. Furthermore, the range of substances was extended to isomers, poly-alcohols, and sugars to obtain more detailed information of the influence of hydroxyl groups on the recorded response. The data show a group-specific correlation of response factors with a correlation coefficient (R2) for, e.g., alcohols and ketones of 0.99. Constant contribution factors of functional groups as mentioned in several GC/FID response studies and prediction models were observed to a limited extent. Interactions of sugar analytes with water showed that transfer of GC/FID to LC/FID data cannot be done in general. The underlying mechanisms revealed several new aspects, which have to be taken into account for future response prediction models, especially of small molecules. Interactions between eluent and analytes show that LC/FID response prediction is more complex and requires more than simple addition of functional group contributions.

Automated determination of picogram-per-liter level of water taste and odor compounds using solid-phase microextraction arrow coupled with gas chromatography-mass spectrometry.

Taste and odor compounds are organic chemicals produced via biochemical processes, and their presence, even at low nanogram-per-liter concentrations, can make water useless for drinking purposes. In this work, a very sensitive and completely automated analytical procedure, based on solid-phase microextraction, has been developed and optimized for determination of seven taste and odor compounds in water media, well below their odor threshold. The selected analytes were isopropyl-3-methoxypyrazine, 2-isobutyl-3-methoxypyrazine, geosmin, 2-methylisoborneol, 2,4,6-trichloroanisole, 2,4,6-bromoanisole, and beta-ionone. Compared with a conventional approach, the recently introduced PAL SPME Arrow showed a significant enhancement in sensitivity and also outstanding robustness and stability. Three commercially available fiber coatings, as well as experimental parameters of the headspace extraction procedure, such as extraction temperature, time, and ionic strength of the aqueous sample, were investigated to optimize the method. The linearity of the response was assessed over a three-orders-of-magnitude range, with R2 values higher than 0.9914. The method was satisfactorily precise, with RSDs less than 11% at the second lowest calibration point (10-26 ng L-1). The calculated LODs (S/N = 3) were below odor thresholds of the target analytes and varied between 0.05 and 0.6 ng L-1, for just 10 mL of water sample. An original and spiked river water sample was also analyzed, and relative recoveries of 75-116% were achieved. Based on these analytical performance characteristics, and compared with other published methods, the present method can be considered as the most sensitive wholly automated approach for determination of taste and odor compounds in water.

Correction: Determining the role of redox-active materials during laser-induced water decomposition.

Correction for 'Determining the role of redox-active materials during laser-induced water decomposition' by Mark-Robert Kalus et al., Phys. Chem. Chem. Phys., 2019, 21, 18636-18651.

Determining the role of redox-active materials during laser-induced water decomposition.

Laser ablation in liquids (LAL) drives the decomposition of the liquid inducing the formation of a large number of different redox equivalents and gases. This not only leads to shielding effects and a decrease of the nanoparticle (NP) productivity but also can directly affect the NP properties such as the oxidation degree. In this study, we demonstrate that liquid decomposition during laser ablation in water is triggered by the redox activity of the 7 different bulk materials used; Au, Pt, Ag, Cu, Fe, Ti and Al, as well as by the reactivity of water with the plasma. Laser ablation of less-noble metals like aluminum leads to a massive gas evolution up to 390 cm3 per hour with molar hydrogen to oxygen ratios of 17.1. For more noble metals such as gold and platinum, water splitting induced by LAL is the dominant feature leading to gas volume formation rates of 10 up to 30 cm3 per hour and molar hydrogen to oxygen ratios of 1.2. We quantify the material-dependent ablation rate, shielding effects as well as the amount of hydrogen peroxide produced, directly affecting the yield and oxidation of the nanoparticles on the long-time scale.

Direct Photolysis of Sulfamethoxazole Using Various Irradiation Sources and Wavelength Ranges-Insights from Degradation Product Analysis and Compound-Specific Stable Isotope Analysis.

The environmental micropollutant sulfamethoxazole (SMX) is susceptible to phototransformation by sunlight and UV-C light which is used for water disinfection. Depending on the environmental pH conditions SMX may be present as neutral or anionic species. This study systematically investigates the phototransformation of these two relevant SMX species using four different irradiation scenarios, i.e., a low, medium, and high pressure Hg lamp and simulated sunlight. The observed phototransformation kinetics are complemented by data from compound-specific stable isotope and transformation product analysis using isotope-ratio and high-resolution mass spectrometry (HRMS). Observed phototransformation kinetics were faster for the neutral than for the anionic SMX species (from 3.4 (LP lamp) up to 6.6 (HP lamp) times). Furthermore, four phototransformation products (with m/z 189, 202, 242, and 260) were detected by HRMS that have not yet been described for direct photolysis of SMX. Isotopic fractionation occurred only if UV-B and UV-A wavelengths prevailed in the emitted irradiation and was most pronounced for the neutral species with simulated sunlight (εC = -4.8 ± 0.1 ‰). Phototransformation of SMX with UV-C light did not cause significant isotopic fractionation. Consequently, it was possible to differentiate sunlight and UV-C light induced phototransformation of SMX. Thus, CSIA might be implemented to trace back wastewater point sources or to assess natural attenuation of SMX by sunlight photolysis. In contrast to the wavelength range, pH-dependent speciation of SMX hardly impacted isotopic fractionation.

Monitoring Microbial Mineralization Using Reverse Stable Isotope Labeling Analysis by Mid-Infrared Laser Spectroscopy.

Assessing the biodegradation of organic compounds is a frequent question in environmental science. Here, we present a sensitive, inexpensive, and simple approach to monitor microbial mineralization using reverse stable isotope labeling analysis (RIL) of dissolved inorganic carbon (DIC). The medium for the biodegradation assay contains regular organic compounds and 13C-labeled DIC with 13C atom fractions (x(13C)DIC) higher than natural abundance (typically 2-50%). The produced CO2 (x(13C) ≈ 1.11%) gradually dilutes the initial x(13C)DIC allowing to quantify microbial mineralization using mass-balance calculations. For 13C-enriched CO2 samples, a newly developed isotope ratio mid-infrared spectrometer was introduced with a precision of x(13C) < 0.006%. As an example for extremely difficult and slowly degradable compounds, CO2 production was close to the theoretical stoichiometry for anaerobic naphthalene degradation by a sulfate-reducing enrichment culture. Furthermore, we could measure the aerobic degradation of dissolved organic carbon (DOC) adsorbed to granular activated carbon in a drinking water production plant, which cannot be labeled with 13C. Thus, the RIL approach can be applied to sensitively monitor biodegradation of various organic compounds under anoxic or oxic conditions.

Investigation of carbon-based nanomaterials as sorbents for headspace in-tube extraction of polycyclic aromatic hydrocarbons.

Carbon-based nanomaterials (CNM) represent promising materials for the application as sorbents in micro- and other extraction devices. In this work, we investigate the applicability of five different CNM (multi-walled carbon nanotubes (MWCNTs), fullerenes, carboxylic acid functionalized multi-walled carbon nanotubes (MWCNTs-COOH), graphene platelets, and carbon nanohorns) for their performance on PAH extraction from the aqueous phase by headspace in-tube extraction (HS-ITEX). Optimal extraction parameters for HS-ITEX were determined using a Box-Behnken experimental design. From the extraction yield response, central point analysis, fullerenes showed the best extraction properties for the eight selected headspace compatible PAHs (naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, and pyrene). Fullerenes were used for a further method validation including the linear range, limit of detection, precision, as well as recovery. Finally, extraction yields were compared to a commercial material (Tenax GR), demonstrating that fullerene represents a better option as sorbent in ITEX for PAH analysis. Method detection limits for the PAH on fullerene ranged from 10 to 300 ng L-1, with recoveries between 45 and 103%.

Sorbent material characterization using in-tube extraction needles as inverse gas chromatography column.

In-tube extraction is a full automated enrichment technique that consists of a stainless-steel needle, packed with sorbent material for the extraction of volatile and semivolatile compounds. In principle, all particulate sorbents used for enrichment in air or headspace analysis can be used. However, the selection of the sorbents is merely based on empirical considerations rather than on experimental data, which is caused by a lack of knowledge about the relevant physicochemical properties of the sorbent. Especially, the knowledge of hydrostatic, advective, diffusive, and dispersion mechanisms in addition to sorption enthalpies are important for combined transport and sorption models. To provide these missing parameters, we developed and evaluated a method in which an ordinary in-tube extraction needle was employed directly as column for sorbent characterization by inverse gas chromatography. As probe compounds, benzene, ethyl acetate, and 3-methyl-1-butanol were used to determine thermodynamic parameters such as sorption enthalpy, partitioning constant between the solid and gas phase, and kinetic parameters such as the diffusion coefficient, dispersion coefficient, and apparent permeability, exemplarily. As sorbent, three commercially available phases were characterized to demonstrate the applicability of the method.

PAL SPME Arrow--evaluation of a novel solid-phase microextraction device for freely dissolved PAHs in water.

After more than 25 years, solid-phase microextraction (SPME) has gained widespread acceptance as a well-automatable and flexible microextraction technique, while its instrumental basis remained mostly unchanged. The novel PAL (Prep And Load solution) SPME Arrow combines the advantages of SPME with the benefits of extraction techniques providing larger sorption phase volumes such as stir bar sorptive extraction (SBSE). It thereby avoids the inherent drawbacks of both techniques such as limitations in method automation in the case of SBSE, as well as the small sorption phase volumes and the lacking fiber robustness of classical SPME fibers. This new design is based on a robust stainless steel backbone, carrying, the screw connection to the PAL sampler, the enlarged sorption phase, and an arrow-shaped tip for conservative penetration of septa (hence the name). An outer capillary encloses this phase apart from enrichment and desorption processes and rests against the tip during transfer and penetrations, resulting in a homogeneously closed device. Here, we present an evaluation and a comparison of the novel PAL SPME Arrow with classical SPME fibers, extracting polycyclic aromatic hydrocarbons (PAHs) as model analytes, from the freely dissolved fraction in lab water and groundwater via direct immersion using polydimethylsiloxane (PDMS) as common sorption phase material. Limits of detection, repeatabilities, and extraction yields were determined for the PAL SPME Arrow and compared to data of classical SPME fibers and SBSE bars. Results indicate a significant benefit in extraction efficiency due to the larger sorption phase volume. It is accompanied by faultless mechanical robustness and thus better reliability, especially in case of prolonged, unattended, and automated operation. As an exemplary application, the water-soluble fraction of PAHs and derivatives in a roofing felt sample was quantified.

Systematic comparison of static and dynamic headspace sampling techniques for gas chromatography.

Six automated, headspace-based sample preparation techniques were used to extract volatile analytes from water with the goal of establishing a systematic comparison between commonly available instrumental alternatives. To that end, these six techniques were used in conjunction with the same gas chromatography instrument for analysis of a common set of volatile organic carbon (VOC) analytes. The methods were thereby divided into three classes: static sampling (by syringe or loop), static enrichment (SPME and PAL SPME Arrow), and dynamic enrichment (ITEX and trap sampling). For PAL SPME Arrow, different sorption phase materials were also included in the evaluation. To enable an effective comparison, method detection limits (MDLs), relative standard deviations (RSDs), and extraction yields were determined and are discussed for all techniques. While static sampling techniques exhibited sufficient extraction yields (approx. 10-20 %) to be reliably used down to approx. 100 ng L(-1), enrichment techniques displayed extraction yields of up to 80 %, resulting in MDLs down to the picogram per liter range. RSDs for all techniques were below 27 %. The choice on one of the different instrumental modes of operation (aforementioned classes) was thereby the most influential parameter in terms of extraction yields and MDLs. Individual methods inside each class showed smaller deviations, and the least influences were observed when evaluating different sorption phase materials for the individual enrichment techniques. The option of selecting specialized sorption phase materials may, however, be more important when analyzing analytes with different properties such as high polarity or the capability of specific molecular interactions. Graphical Abstract PAL SPME Arrow during the extraction of volatile analytes from the headspace of an aqueous sample.