RESUMO
Ceria-platinum-based bilayered thin films deposited by magnetron sputtering were developed and tested in regard to their catalytic activity for methanol oxidation by employing a temperature-programmed reaction (TPR) technique. The composition and structure of the samples were characterized by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). Both conventional (oxide-supported metal nanoparticles [NPs]) and inverse configurations (metal with oxide overlayer) were analyzed to uncover the structural dependence of activity and selectivity of these catalysts with respect to different pathways of methanol oxidation. We clearly demonstrate that the amount of cerium oxide (ceria) loading has a profound influence on methanol oxidation reaction characteristics. Adding a noncontinuous adlayer of ceria greatly enhances the catalytic performance of platinum (Pt) in favor of partial oxidation of methanol (POM), gaining an order of magnitude in the absolute yield of hydrogen. Moreover, the undesired by-production of carbon monoxide (CO) is strongly suppressed, making the ceria-platinum inverse catalyst a great candidate for clean hydrogen production. It is suggested that the methanol oxidation process is facilitated by the synergistic effect between both components of the inverse catalyst (involving oxygen from ceria and providing a reaction site on the adjacent Pt surface) as well as by the fact that the ability of ceria to exchange oxygen (i.e., to alter the oxidation state of Ce between 3+ and 4+) during the reaction is inversely proportional to its thickness. The increased redox capability of the discontinuous ceria adlayer shifts the preferred reaction pathway from dehydrogenation of hydroxymethyl intermediate to CO in favor of its oxidation to formate.
RESUMO
Ni-rich layered oxides LiNi1-x-yMnxCoyO2 (NMC811, x = 0.1 and y = 0.1) are considered promising cathode materials in lithium-ion batteries (LiBs) due to their high energy density. However, those suffer a severe capacity loss upon cycling at high delithiated states. The loss of performance over time can be retarded by Zr doping. Herein, a small amount of Zr is added to NMC811 material via two alternative pathways: during the formation of the transition metal (TM) hydroxide precursor at the co-precipitation step (0.1%-Zr-cp) and during the lithiation at the solid-state synthesis step (0.1%-Zr-ss). In this work, the crystallographic Zr uptake in both 0.1%-Zr-ss and 0.1%-Zr-cp is determined and quantified through synchrotron X-ray diffraction and X-ray absorption spectroscopy. We prove that the inclusion of Zr in the TM site for 0.1%-Zr-cp leads to an improvement of both specific capacity (156 vs 149 mAh/g) and capacity retention (85 vs 82%) upon 100 cycles compared to 0.1%-Zr-ss where the Zr does not diffuse into the active material and forms only an extra phase separated from the NMC811 particles.
RESUMO
Micro-domains of modified surface potential (SP) were created on hydroxyapatite films by direct patterning by mid-energy focused electron beam, typically available as a microprobe of Scanning Electron Microscopes. The SP distribution of these patterns has been studied on sub-micrometer scale by the Kelvin Probe Force Microscopy method as well as lysozyme adsorption. Since the lysozyme is positively charged at physiological pH, it allows us to track positively and negatively charged areas of the SP patterns. Distribution of the adsorbed proteins over the domains was in good agreement with the observed SP patterns.
Assuntos
Durapatita/química , Sondas Moleculares , Proteínas/química , Eletricidade Estática , Concentração de Íons de Hidrogênio , Propriedades de SuperfícieRESUMO
Polymer nanoparticles (NPs) can be highly attractive in numerous applications, including biomedicine, where the use of inorganic matter may be detrimental for living tissues. In conventional wet chemistry, polymerization and functionalization of NPs with specific chemical groups involves complex and often numerous reactions. Here, we report on a solvent-free, single-step, low-temperature plasma-based synthesis of carboxylated NPs produced by the polymerization of acrylic acid under the conditions of a glow discharge. In a monomer-deficient regime, the strong fragmentation of monomer molecules by electron impact results in the formation of 15 nm-sized NPs with <1% retention of the carboxyl groups. In an energy-deficient regime, larger 90 nm-sized NPs are formed with better retention of carboxyl groups that reaches 16%. All types of NPs exhibit a glass transition above room temperature, which makes them highly stable in an aqueous environment with no dissolution or swelling. The NPs are also found to degrade thermally when heated above 150 °C, with a decrease in the mean NP size but with retention of the chemical composition. Thus, plasma polymerization proves to be a versatile approach for the production of polymer NPs with a tunable size distribution, chemical composition, and physical properties.
Assuntos
Acrilatos/química , Resinas Acrílicas/química , Nanopartículas/química , Gases em Plasma/química , Resinas Acrílicas/síntese química , Tamanho da Partícula , PolimerizaçãoRESUMO
Comprehensive understanding of the catalyst corrosion dynamics is a prerequisite for the development of an efficient cathode catalyst in proton-exchange membrane fuel cells. To reach this aim, the behavior of fuel cell catalysts must be investigated directly under reaction conditions. Herein, we applied a strategic combination of in situ/online techniques: in situ electrochemical atomic force microscopy, in situ grazing incidence small angle X-ray scattering, and electrochemical scanning flow cell with online detection by inductively coupled plasma mass spectrometry. This combination of techniques allows in-depth investigation of the potential-dependent surface restructuring of a PtNi model thin film catalyst during potentiodynamic cycling in an aqueous acidic electrolyte. The study reveals a clear correlation between the upper potential limit and structural behavior of the PtNi catalyst, namely, its dealloying and coarsening. The results show that at 0.6 and 1.0 VRHE upper potentials, the PtNi catalyst essentially preserves its structure during the entire cycling procedure. The crucial changes in the morphology of PtNi layers are found to occur at 1.3 and 1.5 VRHE cycling potentials. Strong dealloying at the early stage of cycling is substituted with strong coarsening of catalyst particles at the later stage. The coarsening at the later stage of cycling is assigned to the electrochemical Ostwald ripening process.
RESUMO
Magnetron sputtering is a well-known technique that is commonly used for the deposition of thin compact films. However, as was shown in the 1990s, when sputtering is performed at pressures high enough to trigger volume nucleation/condensation of the supersaturated vapor generated by the magnetron, various kinds of nanoparticles may also be produced. This finding gave rise to the rapid development of magnetron-based gas aggregation sources. Such systems were successfully used for the production of single material nanoparticles from metals, metal oxides, and plasma polymers. In addition, the growing interest in multi-component heterogeneous nanoparticles has led to the design of novel systems for the gas-phase synthesis of such nanomaterials, including metal/plasma polymer nanoparticles. In this featured article, we briefly summarized the principles of the basis of gas-phase nanoparticles production and highlighted recent progress made in the field of the fabrication of multi-component nanoparticles. We then introduced a gas aggregation source of plasma polymer nanoparticles that utilized radio frequency magnetron sputtering of a polymeric target with an emphasis on the key features of this kind of source. Finally, we presented and discussed three strategies suitable for the generation of metal/plasma polymer multi-core@shell or core-satellite nanoparticles: the use of composite targets, a multi-magnetron approach, and in-flight coating of plasma polymer nanoparticles by metal.
RESUMO
A platinum catalyst undergoes complex deterioration process during its operation as a cathode in a proton exchange membrane fuel cell. By using in situ electrochemical atomic force microscopy (EC-AFM) with super-sharp probes, we quantitatively describe the roughening of platinum thin films during electrochemical cycling to different upper potentials, which simulate critical operation regimes of the proton exchange membrane fuel cell. The comprehensive quantitative analysis of morphology changes obtained using common roughness descriptors such as the root mean square roughness, the correlation length and the roughness exponent is correlated with cyclic voltammetry performed simultaneously.
RESUMO
Electrical characterisation of perovskite solar cells consisting of room-temperature atomic-layer-deposited aluminium oxide (RT-ALD-Al2 O3 ) film on top of a methyl ammonium lead triiodide (CH3 NH3 PbI3 ) absorber showed excellent stability of the power conversion efficiency (PCE) over a long time. Under the same environmental conditions (for 355â d), the average PCE of solar cells without the ALD layer decreased from 13.6 to 9.6 %, whereas that of solar cells containing 9 ALD cycles of depositing RT-ALD-Al2 O3 on top of CH3 NH3 PbI3 increased from 9.4 to 10.8 %. Spectromicroscopic investigations of the ALD/perovskite interface revealed that the maximum PCE with the ALD layer is obtained when the so-called perovskite cleaning process induced by ALD precursors is complete. The PCE enhancement over time is probably related to a self-healing process induced by the RT-ALD-Al2 O3 film. This work may provide a new direction for further improving the long-term stability and performance of perovskite solar cells.
RESUMO
Invited for this month's cover is the group of Prof.â Dr. Toshiyuki Mori at National Institute for Materials Science (NIMS), Japan. The front cover picture shows the formation of new active sites on Ni in the anode of a solid oxide fuel cell (SOFC), which displays high performance at intermediate temperature. The combination of processing route design, microanalysis, and surface atomistic simulation provides us with a new design paradigm for fabrication of high-performance SOFCs. Read the full text of the article at 10.1002/cplu.201800170.
RESUMO
In recent years, the lowering of the operation temperature of solid oxide fuel cells (SOFCs) has attracted much attention owing to the trade-off between the best performance and the life span of SOFCs. For this challenge, new active sites on the Ni surfaces in a Nickel-Yttria-Stabilized Zirconia (Ni-YSZ) cermet anode of SOFCs have been created by deposition of trace amounts of platinum oxide (PtOx ) followed by an activation step of the anode at 1073â K in a hydrogen flow. The internal resistance (IR) free value (185â mA cm-2 at 0.8â V) observed for the single cell with an anode sputtered with a trace amount of PtOx (Pt content in anode: from 9 to 91â ppm) at 973â K is conspicuously higher than that of a similar single cell with a nonsputtered cermet anode (85â mA cm-2 ) at 0.8â V and 1073â K. Transmission electron microscopy microanalysis shows that the defect structure is formed on a partially oxidized Ni surface by active Pt species. Also, surface atomistic simulation on NiO (111) predicts the formation of Frenkel defect clusters with Pt cations, which partially cover the Ni surface. The formation of Frenkel defect clusters on the partially oxidized Ni surface (i.e., creation of new active sites for formation of water molecules) promotes the anode reaction, resulting in improvements in the anode performance of SOFC single cells at 973â K. Design of the aforementioned new active sites on Ni through sputtering of trace amounts of PtOx provides a great opportunity for "radical innovation" in the design of intermediate-temperature SOFCs.
RESUMO
Photocatalytic and in situ microbial activity of the amorphous and annealed states of Ag-doped and un-doped titania were examined. Studies on their structure, morphology, composition, and the photo-absorption characteristics of these materials were performed. These results were correlated with the photocatalytic and microbial activity against methicillin resistant Staphylococcus aureus K324 (MRSA), methicillin susceptible S. aureus ATCC 25923 (MSSA), Escherichia coli PA 170, and yeasts Candida albicans ATCC 90028. The annealed powders containing anatase form of titania exhibited relatively higher photocatalytic activity,corresponding to activity against MRSA,when exposed to UV-A radiation. In comparison, amorphous powders exhibited low photoactivity and showed poor antibacterial performance against MRSA under UV-A exposure. Doping of amorphous titania with Ag resulted in an anti-MRSA effect without exposure to UV radiation. In the Ag-doped crystalline anatase samples, the size of Ag primary nanocrystallites increased, which led to the decrease in the surface concentration of Ag and detriment anti-MRSA activity.