Inhibition of enamel demineralization by an ion-releasing tooth-coating material.

PURPOSE: To evaluate the inhibitory effect of a surface pre-reacted glass-ionomer (S-PRG) filler-containing tooth-coating material on enamel demineralization. The outer surface of the S-PRG filler is in a state in which ions are readily released. METHODS: Human enamel blocks were incubated in lactic acid solution (pH 4.0) with and without a disk (n=6) made of the cured tooth-coating material. Test solutions were changed every 24 hours and incubation was continued for 4 days. The pH and amount of fluoride released were measured with an electrode and ion meter, respectively. The concentrations of ions (aluminum, boron, calcium, phosphorus, silicon, sodium, and strontium) were measured by inductively coupled plasma atomic emission spectroscopy. The surface of the enamel block was observed with a scanning electron microscope. RESULTS: Enamel demineralization was not observed in an enamel block incubated with a disk of the tooth-coating material. Ions released from S-PRG filler had an acid buffering action in the low pH lactic acid solution. However, in the enamel block-only solution showing high levels of calcium ion release, the degree of demineralization was correlated with morphological changes of the enamel surface. CLINICAL SIGNIFICANCE: Due to the buffering effects of the pre-reacted glass-ionomer surface by ion release, the S-PRG filler-containing tooth-coating material inhibited enamel demineralization by neutralizing the acidic environment at an early time point.

Effect of Particle Sizes and Contents of Surface Pre-Reacted Glass Ionomer Filler on Mechanical Properties of Auto-Polymerizing Resin.

Herein, the mechanical properties of an auto-polymerizing resin incorporated with a surface pre-reacted glass ionomer (S-PRG) filler were evaluated. For this, S-PRG fillers with particle sizes of 1 µm (S-PRG-1) and 3 µm (S-PRG-3) were mixed at 10, 20, 30, and 40 wt% to prepare experimental resin powders. The powders and a liquid (powder/liquid ratio = 1.0 g/0.5 mL) were kneaded and filled into a silicone mold to obtain rectangular specimens. The flexural strength and modulus (n = 12) were recorded via a three-point bending test. The flexural strengths of S-PRG-1 at 10 wt% (62.14 MPa) and S-PRG-3 at 10 and 20 wt% (68.68 and 62.70 MPa, respectively) were adequate (>60 MPa). The flexural modulus of the S-PRG-3-containing specimen was significantly higher than that of the S-PRG-1-containing specimen. Scanning electron microscopy observations of the specimen fracture surfaces after bending revealed that the S-PRG fillers were tightly embedded and scattered in the resin matrix. The Vickers hardness increased with an increasing filler content and size. The Vickers hardness of S-PRG-3 (14.86-15.48 HV) was higher than that of S-PRG-1 (13.48-14.97 HV). Thus, the particle size and content of the S-PRG filler affect the mechanical properties of the experimental auto-polymerizing resin.

Contact Angle and Cell Adhesion of Micro/Nano-Structured Poly(lactic-co-glycolic acid) Membranes for Dental Regenerative Therapy.

Biodegradable membranes are used in regenerative dentistry for guided tissue regeneration (GTR) and guided bone regeneration (GBR). In this study, patterned poly(lactic-co-glycolic acid) (PLGA) membranes with groove, pillar, and hole structures were successfully fabricated by thermal nanoimprinting. Their surfaces were evaluated for topography by scanning electron microscopy and laser microscopy, for hydrophobicity/hydrophilicity by contact angle analysis, and for MC3T3-E1 cell adhesion. The sizes of the patterns on the surfaces of the membranes were 0.5, 1.0, and 2.0 µm, respectively, with the height/depth being 1.0 µm. The pillared and holed PLGA membranes were significantly more hydrophobic than the non-patterned PLGA membranes (p < 0.05). However, the 0.5 µm- and 1.0 µm-grooved PLGA membranes were significantly more hydrophilic than the non-patterned PLGA membranes (p < 0.05). The 0.5 µm-grooved, pillared, and holed membranes exhibited significantly superior adhesion to the MC3T3-E1 cells than the non-patterned PLGA (p < 0.05). These results suggest that patterned PLGA membranes can be clinically used for GTR and GBR in the dental regeneration field.

Proliferation of Saos-2 and Ca9-22 cells on grooved and pillared titanium surfaces.

BACKGROUND: Surface nanostructures in titanium (Ti) oral implants are critical for rapid osseointegration. OBJECTIVE: The purpose of this study was to evaluate the growth of osteoblast-like (Saos-2) and epithelial-like (Ca9-22) cells on nanopatterned Ti films. METHODS: Ti films with 500 nm grooves and pillars were fabricated by nanoimprinting, and seeded with Saos-2 and Ca9-22 cells. Cell viability and morphology were assessed by cell proliferation assay and scanning electron microscopy, respectively. RESULTS: As assessed after 1 hour, proliferation of Saos-2 cells was most robust on grooved films than on pillared and smooth films, in this order. These cells approximately doubled on grooved and pillared substrates in 24 hours and after 5 days, but not on smooth surfaces. In contrast, Ca9-22 cells favored smooth surfaces, followed by grooved and pillared films. Indeed, cells sparsely adhered to pillared films over 5 days of incubation (p < 0.05). CONCLUSIONS: The data show that Saos-2 and Ca9-22 cells respond differently to different nanostructures, and highlight the potential use of nanopatterns to promote bone regeneration or to prevent epithelial downgrowth at the implant-bone interface.

Protective Effects of GIC and S-PRG Filler Restoratives on Demineralization of Bovine Enamel in Lactic Acid Solution.

This study was aimed at investigating the protective effects of glass ionomer cement (GIC) and surface pre-reacted glass ionomer (S-PRG) fillers used as dental restorative materials on demineralization of bovine enamel. GlasIonomer FX ULTRA (FXU), Fuji IX GP Extra (FIXE), CAREDYNE RESTORE (CDR) were used as GICs. PRG Barrier Coat (BC) was used as the S-PRG filler. They were incubated in a lactic acid solution (pH = 4.0) for six days at a temperature of 37 °C. The mineral was etched from the enamel surface, and a large number of Ca and P ions were detected in solution. The Al, F, Na, Sr, and Sr ions were released in GICs and S-RPG fillers. The Zn ion was released only in CDR and the B ion was released only in BC. The presence of apparent enamel prism peripheries was observed after six days of treatment for the group containing only enamel blocks. pH values for the FXU, FIXE, CDR, BC, and enamel block groups after six days were 6.5, 6.6, 6.7, 5.9, and 5.1, respectively. Therefore, the observed pH neutralization effect suppressed progression of caries due to the release of several ions from the restoratives.