Sensitization of silicon by singlet exciton fission in tetracene.

Silicon dominates contemporary solar cell technologies1. But when absorbing photons, silicon (like other semiconductors) wastes energy in excess of its bandgap2. Reducing these thermalization losses and enabling better sensitivity to light is possible by sensitizing the silicon solar cell using singlet exciton fission, in which two excited states with triplet spin character (triplet excitons) are generated from a photoexcited state of higher energy with singlet spin character (a singlet exciton)3-5. Singlet exciton fission in the molecular semiconductor tetracene is known to generate triplet excitons that are energetically matched to the silicon bandgap6-8. When the triplet excitons are transferred to silicon they create additional electron-hole pairs, promising to increase cell efficiencies from the single-junction limit of 29 per cent to as high as 35 per cent9. Here we reduce the thickness of the protective hafnium oxynitride layer at the surface of a silicon solar cell to just eight angstroms, using electric-field-effect passivation to enable the efficient energy transfer of the triplet excitons formed in the tetracene. The maximum combined yield of the fission in tetracene and the energy transfer to silicon is around 133 per cent, establishing the potential of singlet exciton fission to increase the efficiencies of silicon solar cells and reduce the cost of the energy that they generate.

Origins of Photoluminescence Instabilities at Halide Perovskite/Organic Hole Transport Layer Interfaces.

Metal halide perovskites are promising for optoelectronic device applications; however, their poor stability under solar illumination remains a primary concern. While the intrinsic photostability of isolated neat perovskite samples has been widely discussed, it is important to explore how charge transport layers─employed in most devices─impact photostability. Herein, we study the effect of organic hole transport layers (HTLs) on light-induced halide segregation and photoluminescence (PL) quenching at perovskite/organic HTL interfaces. By employing a series of organic HTLs, we demonstrate that the HTL's highest occupied molecular orbital energy dictates behavior; furthermore, we reveal the key role of halogen loss from the perovskite and subsequent permeation into organic HTLs, where it acts as a PL quencher at the interface and introduces additional mass transport pathways to facilitate halide phase separation. In doing so, we both reveal the microscopic mechanism of non-radiative recombination at perovskite/organic HTL interfaces and detail the chemical rationale for closely matching the perovskite/organic HTL energetics to maximize solar cell efficiency and stability.

Adduct-based p-doping of organic semiconductors.

Electronic doping of organic semiconductors is essential for their usage in highly efficient optoelectronic devices. Although molecular and metal complex-based dopants have already enabled significant progress of devices based on organic semiconductors, there remains a need for clean, efficient and low-cost dopants if a widespread transition towards larger-area organic electronic devices is to occur. Here we report dimethyl sulfoxide adducts as p-dopants that fulfil these conditions for a range of organic semiconductors. These adduct-based dopants are compatible with both solution and vapour-phase processing. We explore the doping mechanism and use the knowledge we gain to 'decouple' the dopants from the choice of counterion. We demonstrate that asymmetric p-doping is possible using solution processing routes, and demonstrate its use in metal halide perovskite solar cells, organic thin-film transistors and organic light-emitting diodes, which showcases the versatility of this doping approach.

Halide Perovskites: Is It All about the Interfaces?

Design and modification of interfaces, always a critical issue for semiconductor devices, has become a primary tool to harness the full potential of halide perovskite (HaP)-based optoelectronics, including photovoltaics and light-emitting diodes. In particular, the outstanding improvements in HaP solar cell performance and stability can be primarily ascribed to a careful choice of the interfacial layout in the layer stack. In this review, we describe the unique challenges and opportunities of these approaches (section 1). For this purpose, we first elucidate the basic physical and chemical properties of the exposed HaP thin film and crystal surfaces, including topics such as surface termination, surface reactivity, and electronic structure (section 2). This is followed by discussing experimental results on the energetic alignment processes at the interfaces between the HaP and transport and buffer layers. This section includes understandings reached as well as commonly proposed and applied models, especially the often-questionable validity of vacuum level alignment, the importance of interface dipoles, and band bending as the result of interface formation (section 3). We follow this by elaborating on the impact of the interface formation on device performance, considering effects such as chemical reactions and surface passivation on interface energetics and stability. On the basis of these concepts, we propose a roadmap for the next steps in interfacial design for HaP semiconductors (section 4), emphasizing the importance of achieving control over the interface energetics and chemistry (i.e., reactivity) to allow predictive power for tailored interface optimization.

Erratum: Corrigendum: Beating the thermodynamic limit with photo-activation of n-doping in organic semiconductors.

Nature Materials 16, 1209-1215 (2017); published online 13 November 2017; corrected after print 15 December 2017. In the version of this Article originally published, the source of 'ZADN' stated in the Methods should have read 'obtained as free research samples from Guangzhou ChinaRay OptoelectronicMaterials' instead of 'China-Ray'.

Corrigendum: Beating the thermodynamic limit with photo-activation of n-doping in organic semiconductors.

This corrects the article DOI: 10.1038/nmat5027.

Beating the thermodynamic limit with photo-activation of n-doping in organic semiconductors.

Chemical doping of organic semiconductors using molecular dopants plays a key role in the fabrication of efficient organic electronic devices. Although a variety of stable molecular p-dopants have been developed and successfully deployed in devices in the past decade, air-stable molecular n-dopants suitable for materials with low electron affinity are still elusive. Here we demonstrate that photo-activation of a cleavable air-stable dimeric dopant can result in kinetically stable and efficient n-doping of host semiconductors, whose reduction potentials are beyond the thermodynamic reach of the dimer's effective reducing strength. Electron-transport layers doped in this manner are used to fabricate high-efficiency organic light-emitting diodes. Our strategy thus enables a new paradigm for using air-stable molecular dopants to improve conductivity in, and provide ohmic contacts to, organic semiconductors with very low electron affinity.

Mixed-Halide Perovskites with Stabilized Bandgaps.

One merit of organic-inorganic hybrid perovskites is their tunable bandgap by adjusting the halide stoichiometry, an aspect critical to their application in tandem solar cells, wavelength-tunable light emitting diodes (LEDs), and lasers. However, the phase separation of mixed-halide perovskites caused by light or applied bias results in undesirable recombination at iodide-rich domains, meaning open-circuit voltage (VOC) pinning in solar cells and infrared emission in LEDs. Here, we report an approach to suppress halide redistribution by self-assembled long-chain organic ammonium capping layers at nanometer-sized grain surfaces. Using the stable mixed-halide perovskite films, we are able to fabricate efficient and wavelength-tunable perovskite LEDs from infrared to green with high external quantum efficiencies of up to 5%, as well as linearly tuned VOC from 1.05 to 1.45 V in solar cells.

Low-Temperature Synthesis of a TiO2/Si Heterojunction.

The classical SiO2/Si interface, which is the basis of integrated circuit technology, is prepared by thermal oxidation followed by high temperature (>800 °C) annealing. Here we show that an interface synthesized between titanium dioxide (TiO2) and hydrogen-terminated silicon (H:Si) is a highly efficient solar cell heterojunction that can be prepared under typical laboratory conditions from a simple organometallic precursor. A thin film of TiO2 is grown on the surface of H:Si through a sequence of vapor deposition of titanium tetra(tert-butoxide) (1) and heating to 100 °C. The TiO2 film serves as a hole-blocking layer in a TiO2/Si heterojunction solar cell. Further heating to 250 °C and then treating with a dilute solution of 1 yields a hole surface recombination velocity of 16 cm/s, which is comparable to the best values reported for the classical SiO2/Si interface. The outstanding performance of this heterojunction is attributed to Si-O-Ti bonding at the TiO2/Si interface, which was probed by angle-resolved X-ray photoelectron spectroscopy. Attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) showed that Si-H bonds remain even after annealing at 250 °C. The ease and scalability of the synthetic route employed and the quality of the interface it provides suggest that this surface chemistry has the potential to enable fundamentally new, efficient silicon solar cell devices.

Mechanistic study on the solution-phase n-doping of 1,3-dimethyl-2-aryl-2,3-dihydro-1H-benzoimidazole derivatives.

The discovery of air-stable n-dopants for organic semiconductor materials has been hindered by the necessity of high-energy HOMOs and the air sensitivity of compounds that satisfy this requirement. One strategy for circumventing this problem is to utilize stable precursor molecules that form the active doping complex in situ during the doping process or in a postdeposition thermal- or photo-activation step. Some of us have reported on the use of 1H-benzimidazole (DMBI) and benzimidazolium (DMBI-I) salts as solution- and vacuum-processable n-type dopant precursors, respectively. It was initially suggested that DMBI dopants function as single-electron radical donors wherein the active doping species, the imidazoline radical, is generated in a postdeposition thermal annealing step. Herein we report the results of extensive mechanistic studies on DMBI-doped fullerenes, the results of which suggest a more complicated doping mechanism is operative. Specifically, a reaction between the dopant and host that begins with either hydride or hydrogen atom transfer and which ultimately leads to the formation of host radical anions is responsible for the doping effect. The results of this research will be useful for identifying applications of current organic n-doping technology and will drive the design of next-generation n-type dopants that are air stable and capable of doping low-electron-affinity host materials in organic devices.

Gap states in pentacene thin film induced by inert gas exposure.

We studied gas-exposure effects on pentacene (Pn) films on SiO2 and Au(111) substrates by ultrahigh sensitivity photoelectron spectroscopy, which can detect the density of states of ∼10(16) states eV-1 cm-3 comparable to electrical measurements. The results show the striking effects for Pn/SiO2: exposure to inert gas (N2 and Ar) produces a sharp rise in gap states from ∼10(16) to ∼10(18) states eV-1 cm-3 and pushes the Fermi level closer to the valence band (0.15-0.17 eV), as does exposure to O2 (0.20 eV), while no such gas-exposure effect is observed for Pn/Au(111). The results demonstrate that these gap states originate from small imperfections in the Pn packing structure, which are induced by gas penetration into the film through the crystal grain boundaries.

Triiodide Attacks the Organic Cation in Hybrid Lead Halide Perovskites: Mechanism and Suppression.

Molecular I2 can be produced from iodide-based lead perovskites under thermal stress; triiodide, I3 - , is formed from this I2 and I- . Triiodide attacks protic cation MA+ - or FA+ -based lead halide perovskites (MA+ , methylammonium; FA+ , formamidinium) as explicated through solution-based nuclear magnetic resonance (NMR) studies: triiodide has strong hydrogen-bonding affinity for MA+ or FA+ , which leads to their deprotonation and perovskite decomposition. Triiodide is a catalyst for this decomposition that can be obviated through perovskite surface treatment with thiol reducing agents. In contrast to methods using thiol incorporation into perovskite precursor solutions, no penetration of the thiol into the bulk perovskite is observed, yet its surface application stabilizes the perovskite against triiodide-mediated thermal stress. Thiol applied to the interface between FAPbI3 and Spiro-OMeTAD ("Spiro") prevents oxidized iodine species penetration into Spiro and thus preserves its hole-transport efficacy. Surface-applied thiol affects the perovskite work function; it ameliorates hole injection into the Spiro overlayer, thus improving device performance. It helps to increase interfacial adhesion ("wetting"): fewer voids are observed at the Spiro/perovskite interface if thiols are applied. Perovskite solar cells (PSCs) incorporating interfacial thiol treatment maintain over 80% of their initial power conversion efficiency (PCE) after 300 h of 85 °C thermal stress.

Thin-Film Organic Heteroepitaxy.

Incorporating crystalline organic semiconductors into electronic devices requires understanding of heteroepitaxy given the ubiquity of heterojunctions in these devices. However, while rules for commensurate epitaxy of covalent or ionic inorganic material systems are known to be dictated by lattice matching constraints, rules for heteroepitaxy of molecular systems are still being written. Here, it is found that lattice matching alone is insufficient to achieve heteroepitaxy in molecular systems, owing to weak intermolecular forces that describe molecular crystals. It is found that, in addition, the lattice matched plane also must be the lowest energy surface of the adcrystal to achieve one-to-one commensurate molecular heteroepitaxy over a large area. Ultraviolet photoelectron spectroscopy demonstrates the lattice matched interface to be of higher electronic quality than a disordered interface of the same materials.

Spectral Signatures of a Negative Polaron in a Doped Polymer Semiconductor: Energy Levels and Hubbard U Interactions.

The modern picture of negative charge carriers on conjugated polymers invokes the formation of a singly occupied (spin-up/spin-down) level within the polymer gap and a corresponding unoccupied level above the polymer conduction band edge. The energy splitting between these sublevels is related to on-site Coulomb interactions between electrons, commonly termed Hubbard U. However, spectral evidence for both sublevels and experimental access to the U value is still missing. Here, we provide evidence by n-doping the polymer P(NDI2OD-T2) with [RhCp*Cp]2, [N-DMBI]2, and cesium. Changes in the electronic structure after doping are studied with ultraviolet photoelectron and low-energy inverse photoemission spectroscopies (UPS, LEIPES). UPS data show an additional density of states (DOS) in the former empty polymer gap while LEIPES data show an additional DOS above the conduction band edge. These DOS are assigned to the singly occupied and unoccupied sublevels, allowing determination of a U value of ∼1 eV.

Ultralow doping in organic semiconductors: evidence of trap filling.

Tail states in organic semiconductors have a significant influence on device performances by acting as traps in charge transport. We present a study of the controlled passivation of acceptor tail states in fullerene C(60) by the addition of electrons introduced by molecular n doping. Using ultralow doping, we are able to successively fill the traps with charges and examine the changes in conductivity, activation energy, mobility, and Fermi-level position. Passivation of the traps leads to an increase of the electron mobility in C(60) by more than 3 orders of magnitude, to reach 0.21 cm(2)/(V s).

NiN-Passivated NiO Hole-Transport Layer Improves Halide Perovskite-Based Solar Cell.

The interfaces between inorganic selective contacts and halide perovskites (HaPs) are possibly the greatest challenge for making stable and reproducible solar cells with these materials. NiOx, an attractive hole-transport layer as it fits the electronic structure of HaPs, is highly stable and can be produced at a low cost. Furthermore, NiOx can be fabricated via scalable and controlled physical deposition methods such as RF sputtering to facilitate the quest for scalable, solvent-free, vacuum-deposited HaP-based solar cells (PSCs). However, the interface between NiOx and HaPs is still not well-controlled, which leads at times to a lack of stability and Voc losses. Here, we use RF sputtering to fabricate NiOx and then cover it with a NiyN layer without breaking vacuum. The NiyN layer protects NiOx doubly during PSC production. Firstly, the NiyN layer protects NiOx from Ni3+ species being reduced to Ni2+ by Ar plasma, thus maintaining NiOx conductivity. Secondly, it passivates the interface between NiOx and the HaPs, retaining PSC stability over time. This double effect improves PSC efficiency from an average of 16.5% with a 17.4% record cell to a 19% average with a 19.8% record cell and increases the device stability.

Powerful Organic Molecular Oxidants and Reductants Enable Ambipolar Injection in a Large-Gap Organic Homojunction Diode.

Doping has proven to be a critical tool for enhancing the performance of organic semiconductors in devices like organic light-emitting diodes. However, the challenge in working with high-ionization-energy (IE) organic semiconductors is to find p-dopants with correspondingly high electron affinity (EA) that will improve the conductivity and charge carrier transport in a film. Here, we use an oxidant that has been recently recognized to be a very strong p-type dopant, hexacyano-1,2,3-trimethylene-cyclopropane (CN6-CP). The EA of CN6-CP has been previously estimated via cyclic voltammetry to be 5.87 eV, almost 300 meV higher than other known high-EA organic molecular oxidants. We measure the frontier orbitals of CN6-CP using ultraviolet and inverse photoemission spectroscopy techniques and confirm a high EA value of 5.88 eV in the condensed phase. The introduction of CN6-CP in a film of large-band-gap, large-IE phenyldi(pyren-1-yl)phosphine oxide (POPy2) leads to a significant shift of the Fermi level toward the highest occupied molecular orbital and a 2 orders of magnitude increase in conductivity. Using CN6-CP and n-dopant (pentamethylcyclopentadienyl)(1,3,5-trimethylbenzene)ruthenium (RuCp*Mes)2, we fabricate a POPy2-based rectifying p-i-n homojunction diode with a 2.9 V built-in potential. Blue light emission is achieved under forward bias. This effect demonstrates the dopant-enabled hole injection from the CN6-CP-doped layer and electron injection from the (RuCp*Mes)2-doped layer in the diode.

Controlled n-Doping of Naphthalene-Diimide-Based 2D Polymers.

2D polymers (2DPs) are promising as structurally well-defined, permanently porous, organic semiconductors. However, 2DPs are nearly always isolated as closed shell organic species with limited charge carriers, which leads to low bulk conductivities. Here, the bulk conductivity of two naphthalene diimide (NDI)-containing 2DP semiconductors is enhanced by controllably n-doping the NDI units using cobaltocene (CoCp2 ). Optical and transient microwave spectroscopy reveal that both as-prepared NDI-containing 2DPs are semiconducting with sub-2 eV optical bandgaps and photoexcited charge-carrier lifetimes of tens of nanoseconds. Following reduction with CoCp2 , both 2DPs largely retain their periodic structures and exhibit optical and electron-spin resonance spectroscopic features consistent with the presence of NDI-radical anions. While the native NDI-based 2DPs are electronically insulating, maximum bulk conductivities of >10-4  S cm-1 are achieved by substoichiometric levels of n-doping. Density functional theory calculations show that the strongest electronic couplings in these 2DPs exist in the out-of-plane (π-stacking) crystallographic directions, which indicates that cross-plane electronic transport through NDI stacks is primarily responsible for the observed electronic conductivity. Taken together, the controlled molecular doping is a useful approach to access structurally well-defined, paramagnetic, 2DP n-type semiconductors with measurable bulk electronic conductivities of interest for electronic or spintronic devices.

Hexaazatriphenylene (HAT) versus tri-HAT: the bigger the better?

A new hexaazatriphenylene (HAT) derivative formed by the fusion of three HAT units has been prepared and its electronic and molecular structures have been fully characterized by optical and vibrational Raman spectroscopy, electrochemistry, solid-state UV and inverse photoemission spectroscopy (UPS and IPES), and by quantum-chemical calculations. A comparative HAT versus tri-HAT study was performed. The fusion of three HAT molecules causes modifications in the optical and electrochemical properties consistent with enhanced π-electron delocalization attained in a bigger planar core. Such combined experimental and theoretical studies are useful to balance chemical design with supramolecular engineering directed to find enhanced characteristics for new organic semiconductor applications.

Annealing sequence dependent open-circuit voltage of inverted polymer solar cells attributable to interfacial chemical reaction between top electrodes and photoactive layers.

The ability to laminate and delaminate top metal contacts during the processing and testing of inverted polymer solar cells has led us to uncover the peculiar dependence of their open-circuit voltage (V(oc)) on the annealing sequence. Specifically, thermally annealing inverted polymer solar cells having bulk-heterojunction photoactive layers after top electrode deposition above 100 °C leads to lower V(oc) compared to analogous devices with unannealed photoactive layers or photoactive layers that have been annealed prior to metal electrode deposition. This reduction in V(oc), however, can be reversed when the top electrodes are replaced. This observation is thus a strong indication that such changes in V(oc) with annealing sequence are manifestations of changes at the top electrode-photoactive layer interface, and not structural changes in the bulk of the photoactive layer. Electronic characterization conducted on the photoactive layers and metal contacts after dissection of the polymer solar cells via delamination suggests the reduction of V(oc) on thermal annealing in the presence of the metal top contacts to stem from an interfacial chemical reaction between the photoactive layers and the metal electrodes. This chemically generated interfacial layer is removed upon electrode delamination, effectively reverting the V(oc) to its original value prior to thermal annealing when the top electrodes are replaced.