RESUMO
Sodium tungsten bronze (Na x WO3) is a promising alternative plasmonic material to nanoparticulate gold due to its strong plasmonic resonances in both the visible and near-infrared (NIR) regions. Additional benefits include its simple production either as a bulk or a nanoparticle material at a relatively low cost. In this work, plasmonic Na x WO3 nanoparticles were introduced and mixed into the nanoparticulate zinc oxide electron transport layer of a water processed poly(3-hexylthiophene):phenyl-C61-butyric acid methyl ester (P3HT:PC61BM) nanoparticle (NP) based organic photovoltaic device (NP-OPV). The power conversion efficiency of NP-OPV devices with Na x WO3 NPs added was found to improve by around 35% compared to the control devices, attributed to improved light absorption, resulting in an enhanced short circuit current and fill factor.
RESUMO
In the electron microscope, spectroscopic signals such as the characteristic X-rays or the energy loss of the incident beam can provide an analysis of the local composition or electronic structure. Recent improvements in the energy resolution and sensitivity of electron spectrometers have improved the quality of spectra that can be obtained. Concurrently, the calculations used to simulate and interpret spectra have made major advances. These developments will be briefly reviewed. In recent years, the focus of analytical electron microscopy has moved away from single spectrum acquisition to mapping and imaging. In particular, the use of spectrum imaging (SI), where a full spectrum is acquired and stored at each pixel in the image is becoming widespread. A challenge for the application of spectrum imaging is the processing of such large datasets in order to extract the significant information. When we go beyond the mapping of composition and look to map bonding and electronic structure this becomes both more important and more difficult. Approaches to processing spectrum imaging data sets acquired using electron energy loss spectroscopy (EELS) will be explored in this paper.
Assuntos
Espectroscopia de Perda de Energia de Elétrons/instrumentação , Espectroscopia de Perda de Energia de Elétrons/métodos , Aumento da Imagem/métodos , Espectroscopia de Perda de Energia de Elétrons/tendências , Análise Espectral/instrumentação , Análise Espectral/métodos , Análise Espectral/tendênciasRESUMO
Electron energy-loss spectroscopy (EELS) in the transmission electron microscope (TEM) is used to obtain high-resolution information on the composition and the type of chemical bonding of materials. Spectrum imaging, where a full EEL spectrum is acquired and stored at each pixel in the image, gives an exact correlation of spatial and spectral features. However, determining and extracting the important spectral components from the large amount of information contained in a spectrum image (SI) can be difficult. This paper demonstrates that principal component analysis of EEL SIs can be used to extract chemically relevant components. With weighted or two-way scaled principal component analysis, both compositional and bonding information can be extracted. Mapping of the chemical variations in a partially reduced titanium dioxide sample and the orientation-dependent bonding in boron nitride and carbon nanotubes are given as examples.
RESUMO
We use a combination of experimental measurements and density functional theory calculations to show that modification of the band structure of Cu by additions of Al causes an unexpected enhancement of the dielectric properties. The effect is optimized in alloys with Al contents between 10 and 15 at.% and would result in strong localized surface plasmon resonances at suitable wavelengths of light. This result is surprising as, in general, alloying of Cu increases its DC resistivity and would be expected to increase optical loss. The wavelengths for the plasmon resonances in the optimized alloy are significantly blue-shifted relative to those of pure Cu and provide a new material selection option for the range 2.2-2.8 eV.
RESUMO
AuAl2 is an intermetallic compound with a vivid purple colour attributable to a bulk plasmon energy in the visible part of the spectrum. However, the colour of as-deposited thin films is not as strong and only develops upon annealing. Density functional theory calculations of the dielectric function are presented for a variety of vacancy types and concentrations. The results support the view that the effect of annealing on colour is correlated with a reduction in concentration of Al vacancies. The effect of vacancies on the optical properties can be understood as arising from the complex interplay between interband transitions around the Fermi level and the plasmon energy.
RESUMO
Pure Au is widely used in plasmonic applications even though its use is compromised by significant losses due to damping. There are some elements that are less lossy than Au (e.g. Ag or Al) but they will normally oxidize or corrode under ambient conditions. Here we examine whether alloying Au with a second element would be beneficial for plasmonic applications. In order to evaluate potential alternatives to pure Au, the density of states (DOS), dielectric function and plasmon quality factor have been calculated for alloys and compounds of Au with Al, Cd, Mg, Pd, Pt, Sn, Ti, Zn and Zr. Substitutional alloying of Au with Al, Cd, Mg and Zn was found to slightly improve the plasmonic response. Of the large number of intermetallic compounds studied, only AuAl2, Au3Cd, AuMg, AuCd and AuZn were found to be suitable for plasmonic applications.
RESUMO
The low-loss region of the electron energy-loss spectrum, the valence EELS, provides information about the electronic structure and optical properties of materials. For bulk materials the spectral intensity can be directly connected to the complex dielectric function. Ab initio quantum mechanical calculations have an important role to play in the interpretation of the fine spectral detail and how this can be connected to the material properties. This paper provides an overview of theoretical background to the calculation of valence EELS in bulk solids and gives specific details on how to run such calculations using the WIEN2k code. The comparison of Au and AuAl(2) illustrates how in metals such calculations are successful in reproducing the main spectral details and can be used to understand the origin of the different colours of these two metals.
RESUMO
The simultaneous measurement of structural and chemical information at the atomic scale provides fundamental insights into the connection between form and function in materials science and nanotechnology. We demonstrate structural and chemical mapping in Bi(0.5) Sr(0.5) MnO3 using an aberration-corrected scanning transmission electron microscope. Two-dimensional mapping is made possible by an adapted method for fast acquisition of electron energy-loss spectra. The experimental data are supported by simulations, which help to explain the less intuitive features.
Assuntos
Microscopia Eletrônica de Transmissão e VarreduraRESUMO
Lasers and light-emitting diodes (LEDs) that emit in the blue to green region are often based on InxGa1-xN quantum well structures. Ionization edges in the electron energy-loss spectrum contain fine structures (called the energy-loss near edge structure (ELNES)) and provide information about the electronic structure. In this paper we compare the experimental and calculated ELNES for the N-K ionization edge of InxGa1-xN quantum wells. When the effects of the core-hole are included in the calculations, agreement between experimental and calculated spectra is very good. Strain has been shown to accentuate the effects of In on the ELNES and moves the ionization edge onset down in energy, relative to the other features. These results suggest that ELNES may provide an alternative method to lattice imaging to determine the presence of strain in this system.
RESUMO
Electron energy-loss near-edge structure (ELNES) is a technique that can be used to measure the electronic structure (i.e. bonding) in materials with subnanometre spatial resolution. This review covers the theoretical principles behind the technique, the experimental procedures necessary to acquire good ELNES spectra, including potential artefacts, and gives examples relevant to materials science.