RESUMO
Cellulose-based model materials in the form of fibrillar networks and macromolecular hydrogels were used to investigate the ion-induced swelling in relation to the elasticity and structure of the network. Both networks were charged by the introduction of carboxyl groups onto the cellulose surface, and the dimensions of the networks in aqueous solution were measured as a function of pH. The use of cellulose-model materials that contained either noncrystalline cellulose or cellulose I fibrils made it possible to model the effect of the ion-induced osmotic pressure of a delignified wood fiber wall. The noncrystalline hydrogels represented the noncrystalline domains of the fiber wall and the fibrillar network represented the supramolecular network of cellulose I fibrils of the fiber wall. The experimental results were compared to swelling potentials computed using the Donnan theory, and it was found that the ion-induced water uptake within the cellulose networks followed the theoretical predictions to a large extent. However, fibrillar networks were found to plastically deform upon swelling and deviated from the ideal Donnan theory for polyelectrolyte gel networks. Upon addition of salt to the aqueous phase surrounding the cellulose materials, both hydrogels and fibrillar networks deviated from the Donnan theory predictions, suggesting that structural differences between the networks impact their swelling.
RESUMO
Noncrystalline cellulose-based gel beads were used as a model material to investigate the effect of osmotic stress on a cellulosic network. The gel beads were exposed to osmotic stress by immersion in solutions with different concentrations of high molecular mass dextran and the equilibrium dimensional change of the gel beads was studied using optical microscopy. The volume fraction of cellulose was calculated from the volume of the gel beads in dextran solutions and their dry content and the relation between the cellulose volume fraction and the total osmotic pressure was thus obtained. The results show that the contribution to the osmotic pressure from counterions increases the water-retaining capacity of the beads at high osmotic pressures but also that the main factor controlling the gel bead collapse at high osmotic strains is the resistance to the deformation of the polymer chain network within the beads. Furthermore, the osmotic pressure associated with the deformation of the polymer network, which counteracts the deswelling of the beads, could be fitted to the Wall model indicating that the response of the cellulose polymer networks was independent of the charge of the cellulose. The best fit to the Wall model was obtained when the Flory-Huggins interaction parameter (χ) of the cellulose-water system was set to 0.55-0.60, in agreement with the well-established insolubility of high molecular mass ß-(1,4)-d-glucan polymers in water.
Assuntos
Celulose/química , Dextranos/química , Modelos Químicos , Pressão Osmótica , TermodinâmicaRESUMO
Cellulose from wood fibers can be modified for use in flame-retardant composites as an alternative to halogen-based compounds. For this purpose, sulfite dissolving pulp fibers have been chemically modified by phosphorylation, and the resulting material has been used to prepare cellulose nanofibrils (CNF) that have a width of approximately 3 nm. The phosphorylation was achieved using (NH4)2HPO4 in the presence of urea, and the degree of substitution by phosphorus was determined by X-ray photoelectron spectroscopy, conductometric titration, and nuclear magnetic resonance spectroscopy. The presence of phosphate groups in the structure of CNF has been found to noticeably improve the flame retardancy of this material. The nanopaper sheets prepared from phosphorylated CNF showed self-extinguishing properties after consecutive applications of a methane flame for 3 s and did not ignite under a heat flux of 35 kW/m2, as shown by flammability and cone calorimetry measurements, respectively.
Assuntos
Celulose/química , Retardadores de Chama , Nanofibras , Microscopia de Força Atômica , Microscopia Eletrônica de Varredura , Fosforilação , Análise Espectral/métodos , TermogravimetriaRESUMO
BACKGROUND: Lignocellulosic substrates and pulping process streams are of increasing relevance to biorefineries for second generation biofuels and biochemical production. They are known to be rich in sugars and inhibitors such as phenolic compounds, organic acids and furaldehydes. Phenolic compounds are a group of aromatic compounds known to be inhibitory to fermentative organisms. It is known that inhibition of Sacchromyces cerevisiae varies among phenolic compounds and the yeast is capable of in situ catabolic conversion and metabolism of some phenolic compounds. In an approach to engineer a S. cerevisiae strain with higher tolerance to phenolic inhibitors, we selectively investigated the metabolic conversion and physiological effects of coniferyl aldehyde, ferulic acid, and p-coumaric acid in Saccharomyces cerevisiae. Aerobic batch cultivations were separately performed with each of the three phenolic compounds. Conversion of each of the phenolic compounds was observed on time-based qualitative analysis of the culture broth to monitor various intermediate and final metabolites. RESULT: Coniferyl aldehyde was rapidly converted within the first 24 h, while ferulic acid and p-coumaric acid were more slowly converted over a period of 72 h. The conversion of the three phenolic compounds was observed to involved several transient intermediates that were concurrently formed and converted to other phenolic products. Although there were several conversion products formed from coniferyl aldehyde, ferulic acid and p-coumaric acid, the conversion products profile from the three compounds were similar. On the physiology of Saccharomyces cerevisiae, the maximum specific growth rates of the yeast was not affected in the presence of coniferyl aldehyde or ferulic acid, but it was significantly reduced in the presence of p-coumaric acid. The biomass yields on glucose were reduced to 73 and 54 % of the control in the presence of coniferyl aldehyde and ferulic acid, respectively, biomass yield increased to 127 % of the control in the presence of p-coumaric acid. Coniferyl aldehyde, ferulic acid and p-coumaric acid and their conversion products were screened for inhibition, the conversion products were less inhibitory than coniferyl aldehyde, ferulic acid and p-coumaric acid, indicating that the conversion of the three compounds by Saccharomyces cerevisiae was also a detoxification process. CONCLUSION: We conclude that the conversion of coniferyl aldehyde, ferulic acid and p-coumaric acid into less inhibitory compounds is a form of stress response and a detoxification process. We hypothesize that all phenolic compounds are converted by Saccharomyces cerevisiae using the same metabolic process. We suggest that the enhancement of the ability of S. cerevisiae to convert toxic phenolic compounds into less inhibitory compounds is a potent route to developing a S. cerevisiae with superior tolerance to phenolic compounds.
Assuntos
Acroleína/análogos & derivados , Ácidos Cumáricos/metabolismo , Hidroxibenzoatos/metabolismo , Saccharomyces cerevisiae/metabolismo , Acroleína/metabolismo , Metabolismo , PropionatosRESUMO
The industrial production of cellulolytic enzymes is dominated by the filamentous fungus Trichoderma reesei (anamorph of Hypocrea jecorina). In order to develop optimal enzymatic cocktail, it is of importance to understand the natural regulation of the enzyme profile as response to the growth substrate. The influence of the complexity of cellulose on enzyme production by the microorganisms is not understood. In the present study we attempted to understand how different physical and structural properties of cellulose-rich substrates affected the levels and profiles of extracellular enzymes produced by T. reesei. Enzyme production by T. reesei Rut C-30 was studied in submerged cultures on five different cellulose-rich substrates, namely, commercial cellulose Avicel® and industrial-like cellulosic pulp substrates which consist mainly of cellulose, but also contain residual hemicellulose and lignin. In order to evaluate the hydrolysis of the substrates by the fungal enzymes, the spatial polymer distributions were characterised by cross-polarisation magic angle spinning carbon-13 nuclear magnetic resonance (CP/MAS (13)C-NMR) in combination with spectral fitting. Proteins in culture supernatants at early and late stages of enzyme production were labeled by Tandem Mass Tags (TMT) and protein profiles were analysed by liquid chromatography-tandem mass spectrometry. The data have been deposited to the ProteomeXchange with identifier PXD001304. In total 124 proteins were identified and quantified in the culture supernatants, including cellulases, hemicellulases, other glycoside hydrolases, lignin-degrading enzymes, auxiliary activity 9 (AA9) family (formerly GH61), supporting activities of proteins and enzymes acting on cellulose, proteases, intracellular proteins and several hypothetical proteins. Surprisingly, substantial differences in the enzyme profiles were found even though there were minor differences in the chemical composition between the cellulose-rich substrates.
Assuntos
Celulases/metabolismo , Celulose/metabolismo , Trichoderma/citologia , Trichoderma/enzimologia , Cromatografia Líquida , Meios de Cultura/química , Proteínas Fúngicas/análise , Hidrólise , Espectroscopia de Ressonância Magnética , Microscopia , Proteoma/análise , Espectrometria de Massas em Tandem , Trichoderma/crescimento & desenvolvimentoRESUMO
We demonstrate how to prepare extraordinarily deformable, gas-filled, spherical capsules from nonmodified cellulose. These capsules have a low nominal density, ranging from 7.6 to 14.2 kg/m(3), and can be deformed elastically to 70% deformation at 50% relative humidity. No compressive strain-at-break could be detected for these dry cellulose capsules, since they did not rupture even when compressed into a disk with pockets of highly compressed air. A quantitative constitutive model for the large deformation compression of these capsules is derived, including their high-frequency mechanical response and their low-frequency force relaxation, where the latter is governed by the gas barrier properties of the dry capsule. Mechanical testing corroborated these models with good accuracy. Force relaxation measurements at a constant compression rendered an estimate for the gas permeability of air through the capsule wall, calculated to 0.4 mL µm/m(2) days kPa at 50% relative humidity. These properties taken together open up a large application area for the capsules, and they could most likely be used for applications in compressible, lightweight materials and also constitute excellent model materials for adsorption and adhesion studies.
Assuntos
Cápsulas/química , Celulose/química , Teste de MateriaisRESUMO
The high structural anisotropy and colloidal stability of cellulose nanofibrils' enable the creation of self-standing fibrillar hydrogel networks at very low solid contents. Adding methacrylate moieties on the surface of TEMPO oxidized CNFs allows the formation of more robust covalently crosslinked networks by free radical polymerization of acrylic monomers, exploiting the mechanical properties of these networks more efficiently. This technique yields strong and elastic networks but with an undefined network structure. In this work, we use acrylate-capped telechelic polymers derived from the step-growth polymerization of PEG diacrylate and dithiothreitol to crosslink methacrylated TEMPO-oxidized cellulose nanofibrils (MATO CNF). This combination resulted in flexible and strong hydrogels, as observed through rheological studies, compression and tensile loading. The structure and mechanical properties of these hydrogel networks were found to depend on the dimensions of the CNFs and polymer crosslinkers. The structure of the networks and the role of individual components were evaluated with SAXS (Small-Angle X-ray Scattering) and photo-rheology. A thorough understanding of hybrid CNF/polymer networks and how to best exploit the capacity of these networks enable further advancement of cellulose-based materials for applications in packaging, soft robotics, and biomedical engineering.
RESUMO
The fundamental understanding concerning cellulose-cellulose interactions under wet and dry conditions remains unclear. This is especially true regarding the drying-induced association of cellulose, commonly described as an irreversible phenomenon called hornification. A fundamental understanding of the mechanisms behind hornification would contribute to new drying techniques for cellulose-based materials in the pulp and paper industry while at the same time enhancing material properties and facilitating the recyclability of cellulose-rich materials. In the present work, the irreversible joining of cellulose-rich surfaces has been studied by subjecting cellulose nanofibril (CNF) films to different heat treatments to establish a link between reswelling properties, structural characteristics as well as chemical and mechanical analyses. A heating time/temperature dependence was observed for the reswelling of the CNF films, which is related to the extent of hornification and is different for different chemical compositions of the fibrils. Further, the results indicate that hornification is related to a diffusion process and that the reswellability increases very slowly over long time, indicating that equilibrium is not reached. Hence, hornification is suggested to be a kinetically limited phenomenon governed by non-covalent reversible interactions and a time/temperature dependence on their forming and breaking.
RESUMO
The biotechnological applications of cellulose nanocrystals (CNCs) continue to grow due to their sustainable nature, impressive mechanical, rheological, and emulsifying properties, upscaled production capacity, and compatibility with other materials, such as protein and polysaccharides. In this study, hydrogels from CNCs and pectin, a plant cell wall polysaccharide broadly used in food and pharma, were produced by calcium ion-mediated internal ionotropic gelation (IG). In the absence of pectin, a minimum of 4 wt% CNC was needed to produce self-supporting gels by internal IG, whereas the addition of pectin at 0.5 wt% enabled hydrogel formation at CNC contents as low as 0.5 wt%. Experimental data indicate that CNCs and pectin interact to give robust and self-supporting hydrogels at solid contents below 2.5 %. Potential applications of these gels could be as carriers for controlled release, scaffolds for cell growth, or wherever else distinct and porous network morphologies are required.
Assuntos
Celulose/química , Hidrogéis/química , Nanopartículas/química , Pectinas/química , Força Compressiva , Espalhamento a Baixo Ângulo , Temperatura , Difração de Raios XRESUMO
Thorough characterization and fundamental understanding of cellulose fibers can help us develop new, sustainable material streams and advanced functional materials. As an emerging nanomaterial, cellulose nanofibrils (CNFs) have high specific surface area and good mechanical properties; however, handling and processing challenges have limited their widespread use. This work reports an in-depth characterization of self-fibrillating cellulose fibers (SFFs) and their use in smart, responsive filters capable of regulating flow and retaining nanoscale particles. By combining direct and indirect characterization methods with polyelectrolyte swelling theories, it was shown that introduction of charges and decreased supramolecular order in the fiber wall were responsible for the exceptional swelling and nanofibrillation of SFFs. Different microscopy techniques were used to visualize the swelling of SFFs before, during, and after nanofibrillation. Through filtration and pH adjustment, smart filters prepared via in situ nanofibrillation showed an ability to regulate the flow rate through the filter and a capacity of retaining 95% of 300 nm (diameter) silica nanoparticles. This exceptionally rapid and efficient approach for making smart filters directly addresses the challenges associated with dewatering of CNFs and bridges the gap between science and technology, making the widespread use of CNFs in high-performance materials a not-so-distant reality.
RESUMO
In this study, the effect of different alcohols and esters as a coagulation medium in the regeneration of cellulose dissolved in an aqueous LiOH-urea-based solvent was thoroughly investigated using various methods such as solid state NMR, X-ray diffraction, water contact angle, oxygen gas permeability, mechanical testing, and scanning electron microscopy. It was observed that several material properties of the regenerated cellulose films follow trends that correlate to the degree of cellulose II crystallinity, which is determined to be set by the miscibility of the coagulant medium (nonsolvent) and the aqueous alkali cellulose solvent rather than the nonsolvents' polarity. This article provides an insight, thus creating a possibility to carefully tune and control the cellulose material properties when tailor-made for different applications.
RESUMO
Nanocomposites from native cellulose with low 2D nanoplatelet content are of interest as sustainable materials combining functional and structural performance. Cellulose nanofibril-graphene oxide (CNF-GO) nanocomposite films are prepared by a physical mixing-drying method, with focus on low GO content, the use of very large GO platelets (2-45µm) and nanostructural characterization using synchrotron x-ray source for WAXS and SAXS. These nanocomposites can be used as transparent coatings, strong films or membranes, as gas barriers or in laminated form. CNF nanofibrils with random in-plane orientation, form a continuous non-porous matrix with GO platelets oriented in-plane. GO reinforcement mechanisms in CNF are investigated, and relationships between nanostructure and suspension rheology, mechanical properties, optical transmittance and oxygen barrier properties are investigated as a function of GO content. A much higher modulus reinforcement efficency is observed than in previous polymer-GO studies. The absolute values for modulus and ultimate strength are as high as 17 GPa and 250 MPa at a GO content as small as 0.07 vol%. The remarkable reinforcement efficiency is due to improved organization of the CNF matrix; and this GO-induced mechanism is of general interest for nanostructural tailoring of CNF-2D nanoplatelet composites.
RESUMO
Bio-based nanocellulose has been shown to possess impressive mechanical properties and simplicity for chemical modifications. The chemical properties are largely influenced by the surface area and functionality of the nanoscale materials. However, finding the typical cross-sections of nanocellulose, such as cellulose nanofibers (CNFs), has been a long-standing puzzle, where subtle changes in extraction methods seem to yield different shapes and dimensions. Here, we extracted CNFs from wood with two different oxidation methods and variations in degree of oxidation and high-pressure homogenization. The cross-sections of CNFs were characterized by small-angle X-ray scattering and wide-angle X-ray diffraction in dispersed and freeze-dried states, respectively, where the results were analyzed by assuming that the cross-sectional distribution was quantized with an 18-chain elementary microfibril, the building block of the cell wall. We find that the results agree well with a pseudosquare unit having a size of about 2.4 nm regardless of sample, while the aggregate level strongly depends on the extraction conditions. Furthermore, we find that aggregates have a preferred cohesion of phase boundaries parallel to the (110)-plane of the cellulose fibril, leading to a ribbon shape on average.
Assuntos
Microfibrilas , Madeira , Celulose/química , Estudos Transversais , Difração de Raios XRESUMO
In this study, the use of cubosomes for topical delivery of the antimicrobial peptide (AMP) LL-37 was investigated. Topical delivery of AMPs is of great interest for treatment of skin infections caused by bacteria, such as Staphylococcus aureus. AMP containing cubosomes were produced by three different preparation protocols and compared: (i) pre-loading, where LL-37 was incorporated into a liquid crystalline gel, which thereafter was dispersed into nanoparticles, (ii) post-loading, where LL-37 was let to adsorb onto pre-formed cubosomes, and (iii) hydrotrope-loading, where LL-37 was incorporated during the spontaneously formed cubosomes in an ethanol/glycerol monooleate mixture. Particle size and size distribution were analyzed using dynamic light scattering (DLS), liquid crystalline structure by small angle x-ray scattering (SAXS) and release of LL-37 by a fluorescamine assay. Proteolytic protection of LL-37 as well as bactericidal effect after enzyme exposure was investigated. The skin irritation potential of cubosomes was examined by an in vitro epidermis model. Finally, the bacterial killing property of the cubosomes was examined by an ex vivo pig skin wound infection model with Staphylococcus aureus. Data showed that a high loading of LL-37 induced formation of vesicles in case of cubosomes prepared by sonication (pre-loading). No release of LL-37 was observed from the cubosomes, indicating strong association of the peptide to the particles. Proteolysis studies showed that LL-37 was fully protected against enzymatic attacks while associated with the cubosomes, also denoting strong association of the peptide to the particles. As a consequence, bactericidal effect after enzyme exposure remained, compared to pure LL-37 which was subjected to proteolysis. No skin irritation potential of the cubosomes was found, thus enabling for topical administration. The ex vivo wound infection model showed that LL-37 in pre-loaded cubosomes killed bacteria most efficient.
Assuntos
Anti-Infecciosos/administração & dosagem , Catelicidinas/administração & dosagem , Sistemas de Liberação de Medicamentos/métodos , Infecções Cutâneas Estafilocócicas/tratamento farmacológico , Infecção dos Ferimentos/tratamento farmacológico , Administração Tópica , Animais , Anti-Infecciosos/efeitos adversos , Anti-Infecciosos/farmacocinética , Peptídeos Catiônicos Antimicrobianos , Catelicidinas/efeitos adversos , Catelicidinas/farmacocinética , Modelos Animais de Doenças , Liberação Controlada de Fármacos , Epiderme/efeitos dos fármacos , Escherichia coli/efeitos dos fármacos , Etanol/química , Glicerídeos/química , Humanos , Cristais Líquidos/química , Testes de Sensibilidade Microbiana , Nanopartículas/química , Espalhamento a Baixo Ângulo , Testes de Irritação da Pele/métodos , Infecções Cutâneas Estafilocócicas/microbiologia , Staphylococcus aureus/efeitos dos fármacos , Suínos , Resultado do Tratamento , Infecção dos Ferimentos/microbiologia , Difração de Raios XRESUMO
Solid-state nuclear magnetic resonance (CP/MAS 13C NMR) spectroscopy has often been used to study cellulose structure, but some features of the cellulose NMR spectrum are not yet fully understood. One such feature is a doublet around 84 ppm, a signal that has been proposed to originate from C4 atoms at cellulose fibril surfaces. The two peaks yield different T1, differing by approximately a factor of 2 at 75 MHz. In this study, we calculate T1 from C4-H4 vector dynamics obtained from molecular dynamics computer simulations of cellulose I beta-water interfacial systems. Calculated and experimentally obtained T1 values for C4 atoms in surface chains fell within the same order of magnitude, 3-20 s. This means that the applied force field reproduces relevant surface dynamics for the cellulose-water interface sufficiently well. Furthermore, a difference in T1 of about a factor of 2 in the range of Larmor frequencies 25-150 MHz was found for C4 atoms in chains located on top of two different crystallographic planes, namely, (110) and (10). A previously proposed explanation that the C4 peak doublet could derive from surfaces parallel to different crystallographic planes is herewith strengthened by computationally obtained evidence. Another suggested basis for this difference is that the doublet originates from C4 atoms located in surface anhydro-glucose units with hydroxymethyl groups pointing either inward or outward. This was also tested within this study but was found to yield no difference in calculated T1.
Assuntos
Celulose/química , Simulação por Computador , Espectroscopia de Ressonância Magnética/métodos , Modelos Moleculares , Água/química , Algoritmos , Carbono/química , Rotação , Propriedades de SuperfícieRESUMO
Hydrothermal treatments of birch wood and kraft pulp were compared for their ability to extract the xylan and produce viscose-grade pulp. Water post-hydrolysis of kraft pulp produced a high-purity cellulosic pulp with lower viscosity but higher cellulose yield than traditional pre-hydrolysis kraft pulping of wood. Post-hydrolysis of pulp also increased the crystallite dimensions and degree of crystallinity in cellulose, and promoted a higher extent of fibril aggregation. The lower specific surface area in post-hydrolyzed pulps, derived from their larger fibril aggregates, decreased the accessibility of OH groups. However, this lower accessibility did not seem to decrease the pulp reactivity to derivatizing chemicals. In the aqueous side-stream, the xylose yield was similar in both pre- and post-hydrolysates, although conducting post-hydrolysis of pulp in a flow-through system enabled the recovery of high purity and molar mass (â¼10â¯kDa) xylan for high-value applications.
RESUMO
Macroscopic beads of water-based gels consisting of uncharged and partially charged ß-(1,4)-d-glucan polymers were developed to be used as a novel model material for studying the water induced swelling of the delignified plant fiber walls. The gel beads were prepared by drop-wise precipitation of solutions of dissolving grade fibers carboxymethylated to different degrees. The internal structure was analyzed using Solid State Cross-Polarization Magic Angle Spinning Carbon-13 Nuclear Magnetic Resonance and Small Angle X-ray Scattering showing that the internal structure could be considered a homogeneous, non-crystalline and molecularly dispersed polymer network. When beads with different charge densities were equilibrated with aqueous solutions of different ionic strengths and/or pH, the change in water uptake followed the trends expected for weak polyelectrolyte gels and the trends found for cellulose-rich fibers. When dried and subsequently immersed in water the beads also showed an irreversible loss of swelling depending on the charge and type of counter-ion which is commonly also found for cellulose-rich fibers. Taken all these results together it is clear that the model cellulose-based beads constitute an excellent tool for studying the fundamentals of swelling of cellulose rich plant fibers, aiding in the elucidation of the different molecular and supramolecular contributions to the swelling.
RESUMO
Nanoscale building blocks of many materials exhibit extraordinary mechanical properties due to their defect-free molecular structure. Translation of these high mechanical properties to macroscopic materials represents a difficult materials engineering challenge due to the necessity to organize these building blocks into multiscale patterns and mitigate defects emerging at larger scales. Cellulose nanofibrils (CNFs), the most abundant structural element in living systems, has impressively high strength and stiffness, but natural or artificial cellulose composites are 3-15 times weaker than the CNFs. Here, we report the flow-assisted organization of CNFs into macroscale fibers with nearly perfect unidirectional alignment. Efficient stress transfer from macroscale to individual CNF due to cross-linking and high degree of order enables their Young's modulus to reach up to 86 GPa and a tensile strength of 1.57 GPa, exceeding the mechanical properties of known natural or synthetic biopolymeric materials. The specific strength of our CNF fibers engineered at multiscale also exceeds that of metals, alloys, and glass fibers, enhancing the potential of sustainable lightweight high-performance materials with multiscale self-organization.
Assuntos
Celulose/química , Nanofibras/química , Materiais Biocompatíveis/química , Celulose/ultraestrutura , Módulo de Elasticidade , Nanofibras/ultraestrutura , Nanotecnologia , Resistência à TraçãoRESUMO
Polydimethyldiallylammonium chloride (PDADMAC) and polystyrene sulfonate (PSS) have been used to build-up polyelectrolyte multilayers (PEMs) on chemical soft wood fibres and on SiO2 at various electrolyte concentrations. Adsorption onto SiO2 was studied using a stagnation point adsorption reflectometer (SPAR), and the adsorbed amount of PDADMAC and PSS on the fibres was determined using nitrogen analysis and Schöniger burning, respectively. The adsorption onto the two substrates was then compared. Paper testing showed that the tensile index (TI) increased by about 90% when 11 layers had been adsorbed, and that there was a correlation between the adsorbed amount and the increase in TI. It was also shown that the particular polymer present in the outermost layer significantly influenced the TI, and that PDADMAC produced a higher TI. A correlation between the adsorbed amount and the TI was also found. Individual fibres were partly treated with a PEM and analysed using a dynamic contact angle analyser (DCA) and environmental scanning electron microscopy (ESEM).
RESUMO
The CP/MAS (13)C NMR line shape of cellulose I has been qualitatively analyzed by direct simulations using the Ornstein-Uhlenbeck stochastic process and the Kubo model. Both approaches describe a anhydroglucose C4 carbon as a oscillator with fluctuating Larmor frequency. The NMR resonance frequency is written omega=omega +omega(t), where the fluctuating part with zero mean was modelled as a stationary Markov diffusion process. The simulation results both motivates the use of multiple line shapes when fitting CP/MAS (13)C NMR spectra recorded on cellulose I and gives some insights into why signals from crystalline cellulose I give rise to Lorentzian line shapes.