Size dependence of exchange bias in Co/CoO nanostructures.

In Co/CoO nanostructures, of dimensions l×3l, at small Co thickness (≈6,10 nm), a strong increase in the bias field and the associated coercive field are found as the nanostructure size is reduced from l=120 nm to l=30 nm. This property indicates that the characteristic length D(AF) within the antiferromagnet which governs exchange-bias effects is the nanostructure size. By contrast, at larger Co thickness (≈23 nm), the exchange-bias field does not depend on the nanostructure size, implying that D(AF) is smaller than the nanostructure size. The results are discussed in the framework of the Malozemoff model, taking into account that the coupling between CoO grains is weak. Exchange bias is dominated either by coupling within the antiferromagnetic layer (6- and 10-nm-thick Co samples) or by ferromagnetic-antiferromagnetic interfacial coupling (23-nm-thick Co sample).

Thin-Film Heterostructures Based on Co/Ni Synthetic Antiferromagnets on Polymer Tapes: Toward Sustainable Flexible Spintronics.

Synthetic antiferromagnets with perpendicular magnetic anisotropy (PMA-SAFs) have gained growing attention for both conventional and next-generation spin-based technologies. While the progress of PMA-SAF spintronic devices on rigid substrates has been remarkable, only few examples of flexible thin-film heterostructures are reported in the literature, all containing platinum group metals (PGMs). Systems based on Co/Ni may offer additional advantages with respect to devices containing PGMs, i.e., low damping and high spin polarization. Moreover, limiting the use of PGMs may relieve the demand for critical raw materials and reduce the environmental impact of related technologies, thus contributing to the transition toward a more sustainable future. Here, we discuss for the first time the realization of Co/Ni-based PMA-SAFs on polymer tapes and exploit it to obtain flexible giant magneto-resistive spin valves (GMR-SVs) with perpendicular magnetic anisotropy. Several combinations of buffer and capping layers (i.e., Pt, Pd, and Cu/Ta) are also investigated. High-quality flexible SAFs with a fully compensated antiferromagnetic region and SVs with a sizable GMR ratio (up to 4.4%), in line with the values reported in the literature for similar systems on rigid substrates, were obtained in all cases. However, we demonstrate that PGMs allows achieving the best results when used as a buffer layer, while Cu is the best choice as a capping layer to optimize the properties of the stacks. We justify the role of buffer and capping layers in terms of different interdiffusion mechanisms occurring at the interface between the metallic layers. These results, along with the high robustness of the samples' properties against bending (up to 180°), indicate that complex and bendable Co/Ni-based heterostructures with reduced content of PGMs can be obtained on flexible tapes, allowing for the development of novel flexible and sustainable spintronic devices for applications in many fields including wearable electronics, soft robotics, and biomedicine.

Disclosing the Nature of Asymmetric Interface Magnetism in Co/Pt Multilayers.

Nowadays, a wide number of applications based on magnetic materials rely on the properties arising at the interface between different layers in complex heterostructures engineered at the nanoscale. In ferromagnetic/heavy metal multilayers, such as the [Co/Pt]N and [Co/Pd]N systems, the magnetic proximity effect was demonstrated to be asymmetric, thus inducing a magnetic moment on the Pt (Pd) layer that is typically higher at the top Co/Pt(Pd) interface. In this work, advanced spectroscopic and imaging techniques were combined with theoretical approaches to clarify the origin of this asymmetry both in Co/Pt trilayers and, for the first time, in multilayer systems that are more relevant for practical applications. The different magnetic moment induced at the Co/Pt interfaces was correlated to the microstructural features that are in turn affected by the growth processes that induce a different intermixing during the film deposition, thus influencing the interface magnetic profile.

Magnetism of Nanoparticles: Effect of the Organic Coating.

The design of novel multifunctional materials based on nanoparticles requires tuning of their magnetic properties, which are strongly dependent on the surface structure. The organic coating represents a unique tool to significantly modify the surface structure trough the bonds between the ligands of the organic molecule and the surface metal atoms. This work presents a critical overview of the effects of the organic coating on the magnetic properties of nanoparticles trough a selection of papers focused on different approaches to control the surface structure and the morphology of nanoparticles' assemblies.

Evolution of the Pt layer deposited on MgO(001) by pulsed laser deposition as a function of the deposition parameters: a scanning tunneling microscopy and energy dispersive X-ray diffractometry/reflectometry study.

A combined ultrahigh vacuum scanning tunneling microscopy (STM-UHV) and energy dispersive X-ray diffractometry/reflectometry (EDXD/EDXR) study of the evolution of face-centered cubic (fcc) Pt layer growth on MgO(100) by pulsed laser deposition as a function of the process parameters such as deposition temperature and deposition duration has been carried out. The aim of this study is to define the best experimental conditions to obtain a controlled film deposition selective on the Pt growth direction (either [111] or [002]). The evolution of the Pt surface morphology as a function of the deposition temperature (T(dep)) from 300 to 700 degrees C has been studied with STM and ED techniques. Results show that the Pt surface, characterized at T(dep) = 300 degrees C by a 3D island morphology, evolves at higher temperatures to a morphology in which the original islands coexist with a distribution of orthogonal 2D stripes. The two features can be associated with the [111] and [002] Pt growth directions of the fcc phase, respectively. For T(dep) = 700 degrees C, the island morphology of the (111) face completely disappears, while the merging process of the (002) stripes reaches completion. The evolution of the morphology at T(dep) = 600 degrees C as a function of the deposition time and thickness has then been studied with STM-UHV, revealing an initial growth of mosaic-like 3D islands. These independent islands, already interconnected, expand along two orthogonal directions and, for longer deposition times, lead to the texture of orthogonal stripes. The EDXR characterization providing the morphological parameters of the films, i.e., thickness and roughness, confirms the above observation and quantifies the effect of such morphological changes on the surface roughness of the Pt film, an important parameter for applications of Pt films as underlayer in magnetic recording media.

Bioactive, nanostructured Si-substituted hydroxyapatite coatings on titanium prepared by pulsed laser deposition.

AIMS: The aim of this work was to deposit silicon-substituted hydroxyapatite (Si-HAp) coatings on titanium for biomedical applications, since it is known that Si-HAp is able to promote osteoblastic cells activity, resulting in the enhanced bone ingrowth. MATERIALS AND METHODS: Pulsed laser deposition (PLD) method was used for coatings preparation. For depositions, Si-HAp targets (1.4 wt % of Si), made up from nanopowders synthesized by wet method, were used. RESULTS: Microstructural and mechanical properties of the produced coatings, as a function of substrate temperature, were investigated by scanning electron and atomic force microscopies, X-ray diffraction, Fourier transform infrared spectroscopy, and Vickers microhardness. In the temperature range of 400-600°C, 1.4-1.5 µm thick Si-HAp films, presenting composition similar to that of the used target, were deposited. The prepared coatings were dense, crystalline, and nanostructured, characterized by nanotopography of surface and enhanced hardness. Whereas the substrate temperature of 750°C was too high and led to the HAp decomposition. Moreover, the bioactivity of coatings was evaluated by in vitro tests in an osteoblastic/osteoclastic culture medium (α-Modified Eagle's Medium). CONCLUSIONS: The prepared bioactive Si-HAp coatings could be considered for applications in orthopedics and dentistry to improve the osteointegration of bone implants.

Highly Textured FeCo Thin Films Deposited by Low Temperature Pulsed Laser Deposition.

The effect of the deposition temperature (Tdep) on the crystallographic orientation of pulsed laser-deposited FeCo/MgO(100) thin film was determined by means of X-ray reflectivity and high resolution trasmission electron microscopy analysis and was correlated with the magnetic anisotropy properties measured by angle dependent hysteresis loops. Highly textured films with a bcc structure and very smooth surface were obtained even at room temperature, the film being [100] and [110] oriented, at Tdep=25 °C and 150 °C, respectively. The cubic symmetry is reflected in the angular dependence of remanent magnetization, showing a 4-fold character, whose in-plane distribution is consistent with the different crystallographic orientations of the films. The high structural quality, even at room temperature, is reflected in a high value of the saturation magnetization and low coercivity, matching the requirements for technological applications.

Physicochemical investigation of pulsed laser deposited carbonated hydroxyapatite films on titanium.

Carbonated hydroxyapatite (CHA)-coated titanium can find wide applications as bone substitute implant in bone and dental surgery and orthopedics, promoting osseointegration with a host bone and ensuring biocompatibility and bioactivity. In this work, carbonated hydroxyapatite films were prepared on titanium substrates by pulsed laser deposition at different substrate temperatures ranging from 30 to 750 degrees C. The properties of films were investigated by scanning electron microscopy, atomic force microscopy, energy-dispersive X-ray diffraction, and Fourier transform infrared spectroscopy. Vickers microhardness measurements of the composite film-substrate systems were performed, and the intrinsic hardness of films was separated from the composite hardness using a "law-of-mixtures" approach and taking into account the indentation size effect. The prepared CHA films are nearly stoichiometric with a Ca/P atomic ratio of 2.0-2.2. The films deposited in the 30-500 degrees C temperature range are about 9 microm thick, amorphous, having an average roughness of 60 nm. At higher temperature, 700-750 degrees C, the films are about 4 microm thick, show a finer surface morphology and an average roughness of 20 nm. At 750 degrees C the films are amorphous, whereas at 700 degrees C they are crystalline and textured along the (202) and (212) directions. The intrinsic hardness of the films increased with an increase in substrate temperature, being as low as 5 GPa at 30 degrees C and reaching a high value of 28 GPa at 700 degrees C. The rich information gained by the joint use of the mentioned techniques allowed a comprehensive characterization of this system.