Spatially Controlled Phase Transition in MoTe2 Driven by Focused Ion Beam Irradiations.

Phase transitions play an important role in tuning the physical properties of two-dimensional (2D) materials as well as developing their high-performance device applications. Here, we reported the observation of a phase transition in few-layered MoTe2 flakes by the irradiation of gallium (Ga+) ions using a focused ion beam (FIB) system. The semiconducting 2H phase of MoTe2 can be controllably converted to the metallic 1T'-like phase via Te defect engineering during irradiations. By taking advantage of the nanometer-sized Ga+ ion probe proved by FIB, in-plane 1T'-2H homojunctions of MoTe2 at submicrometer scale can be fabricated. Furthermore, we demonstrate the improvement of device performance (on-state current over 2 orders of magnitude higher) in MoTe2 transistors using the patterned 1T'-like phase regions as contact electrodes. Our study provides a new strategy to drive the phase transitions in MoTe2, tune their properties, and develop high-performance devices, which also extends the applications of FIB technology in 2D materials and their devices.

Significant hydrogen generation via photo-mechanical coupling in flexible methylammonium lead iodide nanowires.

The flexoelectric effect, which refers to the mechanical-electric coupling between strain gradient and charge polarization, should be considered for use in charge production for catalytically driving chemical reactions. We have previously revealed that halide perovskites can generate orders of higher magnitude flexoelectricity under the illumination of light than in the dark. In this study, we report the catalytic hydrogen production by photo-mechanical coupling involving the photoflexoelectric effect of flexible methylammonium lead iodide (MAPbI3) nanowires (NWs) in hydrogen iodide solution. Upon concurrent light illumination and mechanical vibration, large strain gradients were introduced in flexible MAPbI3 NWs, which subsequently induced significant hydrogen generation (at a rate of 756.5 µmol g-1 h-1, surpassing those values from either photo- or piezocatalysis of MAPbI3 nanoparticles). This photo-mechanical coupling strategy of mechanocatalysis, which enables the simultaneous utilization of multiple energy sources, provides a potentially new mechanism in mechanochemistry for highly efficient hydrogen production.

Quasi-One-Dimensional ZrS3 Nanoflakes for Broadband and Polarized Photodetection with High Tuning Flexibility.

Two-dimensional (2D) layered materials with low crystal symmetries have exhibited unique anisotropic physical properties. Here, we report systematic studies on the photoresponse of field effect transistors (FETs) fabricated using quasi-one-dimensional ZrS3 nanoflakes. The as-fabricated phototransistors exhibit a broadband photocurrent response from ultraviolet to visible regions, where the responsivity and detectivity can be enhanced via additional gate voltages. Furthermore, benefiting from the strong in-plane anisotropy of ZrS3, we observe a gate-voltage and illumination wavelength-dependent polarized photocurrent response, while its sub-millisecond-time response speed is also polarization-dependent. Our results demonstrate the flexible tunability of photodetectors based on anisotropic layered semiconductors, which substantially broadens the application of low symmetry layered materials in polarization-sensitive optoelectronic devices.

Laser irradiation induced structural transformation in layered transition metal trichalcogenide nanoflakes.

Laser irradiation is a powerful tool in inducing changes in lattice structures and properties of two-dimensional (2D) materials through processes such as heating, bleaching, catalysis, etc. However, the underlying mechanisms of such transformations vary dramatically in different 2D materials. Here, we report the structural transformation of layered titanium trisulfide (TiS3) to titanium disulfide (TiS2) after irradiation. We systematically characterized the dependence of the transformation on laser power, flake thickness, irradiation time, and vacuum conditions using microscopic and spectroscopic methods. The underlying mechanism is confirmed as the heat-induced materials decomposition, a process that also occurs in many other transition metal trichalcogenide materials. Furthermore, we demonstrate that this spatial-resolved method also enables the creation of in-plane TiS3-TiS2 heterostructures. Our study identifies a new family of 2D materials that undergo a structural transformation after laser irradiation and enriches the methods available for developing new prototypes of low-dimensional devices in the future.

A broad-spectrum gas sensor based on correlated two-dimensional electron gas.

Designing a broad-spectrum gas sensor capable of identifying gas components in complex environments, such as mixed atmospheres or extreme temperatures, is a significant concern for various technologies, including energy, geological science, and planetary exploration. The main challenge lies in finding materials that exhibit high chemical stability and wide working temperature range. Materials that amplify signals through non-chemical methods could open up new sensing avenues. Here, we present the discovery of a broad-spectrum gas sensor utilizing correlated two-dimensional electron gas at a delta-doped LaAlO3/SrTiO3 interface with LaFeO3. Our study reveals that a back-gating on this two-dimensional electron gas can induce a non-volatile metal to insulator transition, which consequently can activate the two-dimensional electron gas to sensitively and quantitatively probe very broad gas species, no matter whether they are polar, non-polar, or inert gases. Different gas species cause resistance change at their sublimation or boiling temperature and a well-defined phase transition angle can quantitatively determine their partial pressures. Such unique correlated two-dimensional electron gas sensor is not affected by gas mixtures and maintains a wide operating temperature range. Furthermore, its readout is a simple measurement of electric resistance change, thus providing a very low-cost and high-efficient broad-spectrum sensing technique.

Few-Layered MnAl2S4 Dielectrics for High-Performance van der Waals Stacked Transistors.

The gate dielectric layer is an important component in building a field-effect transistor. Here, we report the synthesis of a layered rhombohedral-structured MnAl2S4 crystal, which can be mechanically exfoliated down to the monolayer limit. The dielectric properties of few-layered MnAl2S4 flakes are systematically investigated, whereby they exhibit a relative dielectric constant of over 6 and an electric breakdown field of around 3.9 MV/cm. The atomically smooth thin MnAl2S4 flakes are then applied as a dielectric top gate layer to realize a two-dimensional van der Waals stacked field-effect transistor, which uses MoS2 as a channel material. The fabricated transistor can be operated at a small drain-source voltage of 0.1 V and gate voltages within ranges of ±2 V, which exhibit a large on-off ratio over 107 at 0.5 V and a low subthreshold swing value of 80 mV/dec. Our work demonstrates that the few-layered MnAl2S4 can work as a dielectric layer to realize high-performance two-dimensional transistors, and thus broadens the research on high-κ 2D materials and may provide new opportunities in developing low-dimensional electronic devices with a low power consumption in the future.

Chemical Interaction at the MoO3/CH3NH3PbI3-xClx Interface.

The limited long-term stability of metal halide perovskite-based solar cells is a bottleneck in their drive toward widespread commercial adaptation. The organic hole-transport materials (HTMs) have been implicated in the degradation, and metal oxide layers are proposed as alternatives. One of the most prominent metal oxide HTM in organic photovoltaics is MoO3. However, the use of MoO3 as HTM in metal halide perovskite-based devices causes a severe solar cell deterioration. Thus, the formation of the MoO3/CH3NH3PbI3-xClx (MAPbI3-xClx) heterojunction is systematically studied by synchrotron-based hard X-ray photoelectron spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Raman spectroscopy. Upon MoO3 deposition, significant chemical interaction is induced at the MoO3/MAPbI3-xClx interface: substoichiometric molybdenum oxide is present, and the perovskite decomposes in the proximity of the interface, leading to accumulation of PbI2 on the MoO3 cover layer. Furthermore, we find evidence for the formation of new compounds such as PbMoO4, PbN2O2, and PbO as a result of the MAPbI3-xClx decomposition and suggest chemical reaction pathways to describe the underlying mechanism. These findings suggest that the (direct) MoO3/MAPbI3-xClx interface may be inherently unstable. It provides an explanation for the low power conversion efficiencies of metal halide perovskite solar cells that use MoO3 as a hole-transport material and in which there is a direct contact between MoO3 and perovskite.

Resistance Switching Behavior in Rectangle-Nano-Pattern SrTiO3 Induced by Simple Annealing.

The tunability of semi-conductivity in SrTiO3 single crystal substrates has been realized by a simple encapsulated annealing method under argon atmosphere. This high temperature annealing-induced property changes are characterized by the transmission spectra, scanning electron microscopy (SEM) and synchrotron-based X-ray absorption (XAS). We find the optical property is strongly influenced by the annealing time (with significant decrease of transmittance). A sub gap absorption at ~427 nm is detected which is attributed to the introduction of oxygen vacancy. Interestingly, in the SEM images, annealing-induced regularly rectangle nano-patterns are directly observed which is contributed to the conducting filaments. The XAS of O K-edge spectra shows the changes of electronic structure by annealing. Very importantly, resistance switching response is displayed in the annealed SrTiO3 single crystal. This suggests a possible simplified route to tune the conductivity of SrTiO3 and further develop novel resistance switching materials.

Tunability of MoO3 Thin-Film Properties Due to Annealing in Situ Monitored by Hard X-ray Photoemission.

The chemical and electronic structure of MoO3 thin films is monitored by synchrotron-based hard X-ray photoelectron spectroscopy while annealing from room temperature to 310 °C. Color-coded 2D intensity maps of the Mo 3d and O 1s and valence band maximum (VBM) spectra show the evolution of the annealing-induced changes. Broadening of the Mo 3d and O 1s spectra indicate the reduction of MoO3. At moderate temperatures (120-200 °C), we find spectral evidence for the formation of Mo5+ and at higher temperatures (>165 °C) also of Mo4+ states. These states can be related to the spectral intensity above the VBM attributed to O vacancy induced gap states caused by partial filling of initially unoccupied Mo 4d-derived states. A clear relation between annealing temperature and the induced changes in the chemical and electronic structure suggests this approach as a route for deliberate tuning of MoO3 thin-film properties.

Indan-C60: from a crystalline molecule to photovoltaic application.

Crystalline Indan-C60 and its photovoltaic application were studied. Microsheets and aloe-like micro-nano superstructures can be assembled from Indan-C60. Indan-PC61BM derived from Indan-C60 was further investigated as an acceptor for OPV devices, which shows a higher Voc, FF, and PCE than those obtained using PC61BM.

Optoelectronic properties of a fullerene derivative containing adamantane group.

A fullerene derivative linked with an adamantane cage, [6,6]-phenyl-C61-butyric acid 1-adamantane methyl ester (PC61BAd), has been designed and synthesized. Systematic investigations on its organic field effect performance, photovoltaic properties, and corresponding thermal stability have been made. In OFET device, the electron mobility (µe) of PC61BAd was found to reach a value as high as 0.01 cm(2)/V·s with a high on-off (Ion/Ioff) ratio of 4.9 × 10(6) that is useful for logic device applications. In the organic photovoltaic devices of P3HT:PC61BAd, the power conversion efficiency (PCE) was found to reach 3.31 % in the optimized device. More importantly, the active layer of P3HT:PC61BAd was found to exhibit superior thermal stability over that of P3HT:PC61BM. After heating at 150 °C for 20 h, the P3HT:PC61BAd device still showed a PCE of 2.44 %, demonstrating the applicability of PC61BAd as an acceptor material for the preparation of thermally stable organic solar cells. X-ray diffraction and atomic force microscopy were employed to probe the structure and morphology of PC61BAd and to rationalize its performance as an organic electronic material.

Tailoring of polar and nonpolar ZnO planes on MgO (001) substrates through molecular beam epitaxy.

Polar and nonpolar ZnO thin films were deposited on MgO (001) substrates under different deposition parameters using oxygen plasma-assisted molecular beam epitaxy (MBE). The orientations of ZnO thin films were investigated by in situ reflection high-energy electron diffraction and ex situ X-ray diffraction (XRD). The film roughness measured by atomic force microscopy evolved as a function of substrate temperature and was correlated with the grain sizes determined by XRD. Synchrotron-based X-ray absorption spectroscopy (XAS) was performed to study the conduction band structures of the ZnO films. The fine structures of the XAS spectra, which were consistent with the results of density functional theory calculation, indicated that the polar and nonpolar ZnO films had different electronic structures. Our work suggests that it is possible to vary ZnO film structures from polar to nonpolar using the MBE growth technique and hence tailoring the electronic structures of the ZnO films.PACS: 81; 81.05.Dz; 81.15.Hi.