RESUMO
The search for alternative ways to give a second life to materials paved the way for detailed investigation into three silica-polyethylenimine (Si-PEI) materials for the purpose of CO2 adsorption in carbon capture and storage. A solvent extraction procedure was investigated to recover degraded PEIs and silica, and concomitantly, pyrolysis was evaluated to obtain valuable chemicals such as alkylated pyrazines. An array of thermal (TGA, Py-GC-MS), mechanical (rheology), and spectroscopical (ATR-FTIR, 1H-13C-NMR) methods were applied to PEIs extracted with methanol to determine the relevant physico-chemical features of these polymers when subjected to degradation after use in CO2 capture. Proxies of degradation associated with the plausible formation of urea/carbamate moieties were revealed by Py-GC-MS, NMR, and ATR-FTIR. The yield of alkylpyrazines estimated by Py-GC-MS highlighted the potential of exhausted PEIs as possibly valuable materials in other applications.
Assuntos
Polietilenoimina , Dióxido de Silício , Dióxido de Silício/química , Polietilenoimina/química , Dióxido de Carbono/química , Espectroscopia de Ressonância Magnética , AdsorçãoRESUMO
In recent years, wearable technologies have attracted great attention in physical and chemical sensing applications. Wearable pressure sensors with high sensitivity in low pressure range (<10 kPa) allow touch detection for human-computer interaction and the development of artificial hands for handling objects. Conversely, pressure sensors that perform in a high pressure range (up to 100 kPa), can be used to monitor the foot pressure distribution, the hand stress during movements of heavy weights or to evaluate the cyclist's pressure pattern on a bicycle saddle. Recently, we developed a fully textile pressure sensor based on a conductive polymer, with simple fabrication and scalable features. In this paper, we intend to provide an extensive description on how the mechanical properties of several fabrics and different piezoresistive ink formulation may have an impact in the sensor's response during a dynamic operation mode. These results highlight the complexity of the system due to the presence of various parameters such as the fabric used, the conductive polymer solution, the operation mode and the desired pressure range. Furthermore, this work can lead to a protocol for new improvements and optimizations useful for adapting textile pressure sensors to a large variety of applications.
RESUMO
The use of wheat middlings (WM) and rice husks (RH) as biofillers for mixing with poly(lactic acid) (PLA) matrix to produce new 3D-printable biocomposites was assessed. Filaments containing 10 and 20 wt.% agro-waste-derived biofillers were manufactured and, for the sake of comparison, filaments of neat PLA were also produced. The obtained filaments were characterized via thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), showing potential for further application in additive manufacturing processing. Three-dimensionally printed specimens were thus produced and characterized via: DSC, also evaluating the specific heat capacity (CP) of specific 3D-printed specimens; dynamic mechanical analysis (DMA), also applied for determining the coefficient of linear thermal expansion (CLTE) measured on 3D-printed specimens in two different directions (X and Y); and tensile tests. The latter testing campaign was carried out along three printing directions (X, Y, and Z axes) to test the intrinsic biocomposite features (X-printed samples) as well as interbead and interlayer adhesion (Y- and Z-printed specimens, respectively). All samples demonstrated acceptable properties. The inclusion of a cost-free natural material leads to a strong reduction of the whole material cost. Implementing this new class of composite material to an additive manufacturing technique can significantly reduce the environmental impact of 3D-printed products.
RESUMO
Catalysts are used for producing the vast majority of chemical products. Usually, catalytic membranes are inorganic. However, when dealing with reactions conducted at low temperatures, such as in the production of fine chemicals, polymeric catalytic membranes are preferred due to a more competitive cost and easier tunability compared to inorganic ones. In the present work, nanofibrous mats made of poly(ethylene oxide), PEO, and poly(ethylene glycol) diacrylate, PEGDA, blends with the Au/Pd catalyst are proposed as catalytic membranes for water phase and low-temperature reactions. While PEO is a water-soluble polymer, its blending with PEGDA can be exploited to make the overall PEO/PEGDA blend nanofibers water-resistant upon photo-crosslinking. Thus, after the optimization of the blend solution (PEO molecular weight, PEO/PEGDA ratio, photoinitiator amount), electrospinning process, and UV irradiation time, the resulting nanofibrous mat is able to maintain the nanostructure in water. The addition of the Au6/Pd1 catalyst (supported on TiO2) in the PEO/PEGDA blend allows the production of a catalytic nanofibrous membrane. The reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP), taken as a water phase model reaction, demonstrates the potential usage of PEO-based membranes in catalysis.
RESUMO
The development of electronic skins and wearable devices is rapidly growing due to their broad application fields, such as for biomedical, health monitoring, or robotic purposes. In particular, tactile sensors based on piezoelectric polymers, which feature self-powering capability, have been widely used thanks to their flexibility and light weight. Among these, poly(vinylidenefluoride-trifluoroethylene) (PVDF-TrFE) presents enhanced piezoelectric properties, especially if manufactured in a nanofiber shape. In this work, the enhanced piezoelectric performances of PVDF-TrFE nanofibers were exploited to manufacture a flexible sensor which can be used for wearable applications or e-skin. The piezoelectric signal was collected by carbon black (CB)-based electrodes, which were added to the active layer in a sandwich-like structure. The sensor was electromechanically characterized in a frequency range between 0.25 Hz and 20 Hz-which is consistent with human activities (i.e., gait cycle or accidental bumps)-showing a sensitivity of up to 4 mV/N. The parameters of the signal acquisition circuit were tuned to enable the sensor to work at the required frequency. The proposed electrical model of the nanofibrous piezoelectric sensor was validated by the experimental results. The sensitivity of the sensor remained above 77.5% of its original value after 106 cycles of fatigue testing with a 1 kN compressive force.
RESUMO
Vat photopolymerization, a very efficient and precise object manufacturing technique, still strongly relies on the use of acrylate- and methacrylate-based formulations because of their low cost and high reactivity. However, the environmental impact of using fossil fuel-based, volatile, and toxic (meth)acrylic acid derivatives is driving the scientific community toward the development of alternatives that can match the mechanical performance and three-dimensional (3D) printing processability of traditional photocurable mixtures but are made from environmentally friendly building blocks. Herein, itaconic acid is polymerized with polyols derived from naturally occurring terpenes to produce photocurable poly(ester-thioether)s. The formulation of such polymers using itaconic acid-based reactive diluents allows the preparation of a series of (meth)acrylate-free photocurable resins, which can be 3D printed into solid objects. Extensive analysis has been conducted on the properties of photocured polymers including their thermal, thermomechanical, and mechanical characteristics. The findings suggest that these materials exhibit properties comparable to those of traditional alternatives that are created using harmful and toxic blends. Notably, the photocured polymers are composed of biobased constituents ranging from 75 to 90 wt %, which is among the highest values ever recorded for vat photopolymerization applications.
RESUMO
Graphene (G) can effectively enhance polymers' and polymer composites' electric, thermal, and mechanical properties. Nanofibrous mats have been demonstrated to significantly increase the interlaminar fracture toughness of composite laminates, hindering delamination and, consequently, making such materials safer and more sustainable thanks to increased service life. In the present paper, poly(ethylene oxide) (PEO), polycaprolactone (PCL), and Nylon 66 nanofibers, plain or reinforced with G, were integrated into epoxy-matrix Carbon Fiber Reinforced Polymers (CFRPs) to evaluate the effect of polymers and polymers + G on the laminate mechanical properties. The main aim of this work is to compare the reinforcing action of the different nanofibers (polyether, polyester, and polyamide) and to disclose the effect of G addition. The polymers were chosen considering their thermal properties and, consequently, their mechanism of action against delamination. PEO and PCL, displaying a low melting temperature, melt, and mix during the curing cycle, act via matrix toughening; in this context, they are also used as tools to deploy G specifically in the interlaminar region when melting and mixing with epoxy resin. The high extent of modification stems from an attempt to deploy it in the interlaminar layer, thus diluting further in the resin. In contrast, Nylon 66 does not melt and maintain the nanostructure, allowing laminate toughening via nanofiber bridging. The flexural properties of the nanomodifed CFRPs were determined via a three-point bending (3PB) test, while delamination behavior in Mode I and Mode II was carried out using Double Cantilever Beam (DCB) and End-Notched Flexture (ENF) tests, respectively. The lack of a positive contribution of G in this context is an interesting point to raise in the field of nanoreinforced CFRP.
RESUMO
Nanofibrous mats provide substantial delamination hindering in composite laminates, especially if the polymer (as rubbers) can directly toughen the composite resin. Here, the well-known Nylon 66 nanofibers were impregnated with Nitrile Butadiene Rubber (NBR) for producing rubber/thermoplastic membranes for hampering the delamination of epoxy Carbon Fiber Reinforced Polymers (CFRPs). The starting polyamide mats were electrospun using two different solvent systems, and their effect on the mat's thermal and mechanical properties was investigated, as well as the laminate Mode I delamination resistance via Double Cantilever Beam (DCB) tests. Plain Nylon 66 mats electrospun from formic acid/chloroform perform better than the ones obtained from a solvent system containing trifluoroacetic acid, showing up to + 64% vs + 53% in interlaminar fracture toughness (GI), respectively. The effect of NBR coating benefits both nanofiber types, significantly raising the GI. The best results are obtained when interleaving medium-thickness and lightweight mats (20 µm, 9-10 g/m2) with 70-80 wt% of loaded rubber, achieving up to + 180% in GI. The work demonstrates the ability of NBR at improving the delamination hindering of common polyamide nonwovens, paving the way to the use of NBR-coated Nylon 66 nanofibers as effective interleaves for GI enhancement and overall composite safety improvement.
Assuntos
Fraturas Ósseas , Nanofibras , Humanos , Borracha , Nylons , Fibra de Carbono , Polímeros , Nitrilas , SolventesRESUMO
Still today, concerns regarding delamination limit the widespread use of high-performance composite laminates, such as carbon fiber-reinforced polymers (CFRPs), to replace metals. Nanofibrous mat interleaving is a well-established approach to reduce delamination. However, nanomodifications may strongly affect other laminate thermomechanical properties, especially if achieved by integrating soft materials. Here, this limitation is entirely avoided by using rubbery nitrile butadiene rubber (NBR)/Nomex mixed nanofibers: neither laminate stiffness nor glass-transition temperature (Tg) lowering occurs upon CFRP nanomodification. Stable noncrosslinked nanofibers with up to 60% wt of NBR were produced via single-needle electrospinning, which were then morphologically, thermally, spectroscopically, and mechanically characterized. NBR and Nomex disposition in the nanofiber was investigated via selective removal of the sole rubber fraction, revealing the formation of particular self-assembled structures resembling quasi-core-shell nanofibers or fibril-like hierarchical structures, depending on the applied electrospinning conditions (1.10 and 0.20 mL/h, respectively). Mode I and Mode II loading tests show a significant improvement of the interlaminar fracture toughness of rubbery nanofiber-modified CFRPs, especially GI (up to +180%), while GII enhancement is less pronounced but still significant (+40% in the best case). The two nanofibrous morphologies (quasi-core-shell and fibril-like ones) improve the delamination resistance differently, also suggesting that the way the rubber is located in the nanofibers plays a role in the toughening action. The quasi-core-shell nanofiber morphology provides the best reinforcing action, besides the highest productivity. By contrast, pure Nomex nanofibers dramatically worsen the interlaminar fracture toughness (up to -70% in GI), acting as a release film. The achieved delamination resistance improvements, combined with the retention of both the original laminate stiffness and Tg, pave the way to the extensive and reliable application of NBR/Nomex rubbery nanofibrous mats in composite laminates.
RESUMO
Delamination is the most severe weakness affecting all composite materials with a laminar structure. Nanofibrous mat interleaving is a smart way to increase the interlaminar fracture toughness: the use of thermoplastic polymers, such as poly(ε-caprolactone) and polyamides (Nylons), as nonwovens is common and well established. Here, electrospun polyethylene oxide (PEO) nanofibers are proposed as reinforcing layers for hindering delamination in epoxy-based carbon fiber-reinforced polymer (CFRP) laminates. While PEO nanofibers are well known and successfully applied in medicine and healthcare, to date, their use as composite tougheners is undiscovered, resulting in the first investigation in this application field. The PEO-modified CFRP laminate shows a significant improvement in the interlaminar fracture toughness under Mode I loading: +60% and +221% in G I,C and G I,R, respectively. The high matrix toughening is confirmed by the crack path analysis, showing multiple crack planes, and by the delamination surfaces, revealing that extensive phase separation phenomena occur. Under Mode II loading, the G II enhancement is almost 20%. Despite a widespread phase separation occurring upon composite curing, washings in water do not affect the surface delamination morphology, suggesting a sufficient humidity resistance of the PEO-modified laminate. Moreover, it almost maintains both the original stiffness and glass transition temperature (T g), as assessed via three-point bending and dynamic mechanical analysis tests. The achieved results pave the way for using PEO nanofibrous membranes as a new effective solution for hindering delamination in epoxy-based composite laminates.
RESUMO
Carbon Fiber Reinforced Polymers (CFRPs) are widely used where high mechanical performance and lightweight are required. However, they suffer from delamination and low damping, severely affecting laminate reliability during the service life of components. CFRP laminates modified by rubbery nanofibers interleaving is a recently introduced way to increase material damping and to improve delamination resistance. In this work, nitrile butadiene rubber/poly(ε-caprolactone) (NBR/PCL) blend rubbery nanofibrous mats with 60 wt% NBR were produced in three different mat grammages (5, 10 and 20 g/m2) via single-needle electrospinning and integrated into epoxy CFRP laminates. The investigation demonstrated that both mat grammage and positioning affect CFRP tanδ behaviour, evaluated by dynamic mechanical analysis (DMA) tests, as well as the number of nano-modified interleaves. Double cantilever beam (DCB) tests were carried out to assess the mat grammage effect on the interlaminar fracture toughness. Results show an outstanding improvement of GI,R for all the tested reinforced laminates regardless of the mat grammage (from +140% to +238%), while the effect on GI,C is more dependent on it (up to +140%). The obtained results disclose the great capability of NBR/PCL rubbery nanofibrous mats at improving CFRP damping and interlaminar fracture toughness. Moreover, CFRP damping can be tailored by choosing the number and positioning of the nano-modified interleaves, besides choosing the mat grammage.
RESUMO
In this work, Adenine is proposed, for the first time, as a cross-linker for epoxy resins. Adenine is an amino-substituted purine with heterocyclic aromatic structure showing both proton donors, and hydrogen bonding ability. DSC studies show that adenine is able to positively cross-link a biobased DGEBA-like commercial epoxy precursor with good thermal performance and a reaction mechanism based on a 1H NMR investigation has been proposed. The use of such a formulation to produce composite with recycled short carbon fibers (and virgin ones for the sake of comparison), as well as jute and linen natural fibers as sustainable reinforcements, leads to materials with high compaction and fiber content. The curing cycle was optimized for both carbon fiber and natural fiber reinforced materials, with the aim to achieve the better final properties. All composites produced display good thermal and mechanical properties with glass transition in the range of HT resins (Tg > 150 °C, E' =26 GPa) for the carbon fiber-based composites. The natural fiber-based composites display slightly lower performance that is nonetheless good compared with standard composite performance (Tg about 115-120 °C, E' = 7-9 GPa). The present results thus pave the way to the application of adenine as hardener system for composites production.
RESUMO
Antioxidant activity of native vitamin C (ascorbic acid, AH2) is hampered by instability in solution. Selective loading of AH2 into the inner lumen of natural halloysite nanotubes (HNT) yields a composite nanoantioxidant (HNT/AH2), which was characterized and investigated for its reactivity with the persistent 1,1-diphenyl-2-picrylhydrazyl (DPPHâ¢) radical and with transient peroxyl radicals in the inhibited autoxidation of organic substrates, both in organic solution (acetonitrile) and in buffered (pH 7.4) water in comparison with native AH2. HNT/AH2 showed excellent antioxidant performance being more effective than native ascorbic acid by 131% in acetonitrile and 290% (three-fold) in aqueous solution, under identical settings. Reaction with peroxyl radicals has a rate constant of 1.4 × 106 M-1 s-1 and 5.1 × 104 M-1 s-1, respectively, in buffered water (pH 7.4) and acetonitrile, at 30 °C. Results offer physical understanding of the factors governing HNT/AH2 reactivity. Improved performance of HNT/AH2 is unprecedented among forms of stabilized ascorbic acid and its relevance is discussed on kinetic grounds.
RESUMO
The chiroptical properties of amorphous chiral polymers functionalized with conjugated trans-azoaromatic chromophore linked to the backbone through a chiral cyclic pyrrolidine moiety of one single configuration at the solid state, as thin films, were investigated. For the first time nanometric thin films of amorphous polymers (not liquid crystals) showed a remarkable chiral amplification upon thermal treatment at a temperature close to their Tg. The side-chain azobenzene chromophores rearrangement driven by the enhanced chain mobility seems to favor the formation of nanodomains of conformationally ordered macromolecular chains with one prevailing helical handedness whose optical activity depends on the configuration of the intrinsic chirality of the monomeric units and which as a result are stable at room temperature for a long time.
RESUMO
Polyhydroxyalkanoates (PHAs) can be extracted from mixed microbial cultures (MMCs) by means of dimethyl carbonate (DMC) or combination of DMC and sodium hypochlorite (NaClO). The protocol based on DMC, a green solvent never used before for the extraction of PHAs from MMC, allows an overall polymer recovery of 63%; also the purity and the molecular weight of the recovered polymers are good (98% and 1.2 MDa, respectively). The use of NaClO pretreatment before DMC extraction increases the overall PHA recovery (82%) but lowers the mean molecular weight to 0.6-0.2 MDa. A double extraction with DMC results to be the method of choice for the recovery of high quality PHAs from attractive but challenging MMCs.
Assuntos
Bactérias/metabolismo , Poli-Hidroxialcanoatos/isolamento & purificação , Bactérias/crescimento & desenvolvimento , Técnicas de Cultura Celular por Lotes , Biomassa , Reatores Biológicos/microbiologia , SolventesRESUMO
The successful synthesis of amylose brushes via enzymatic "grafting from" polymerization and the detailed characterization of all synthetic steps by X-ray photoelectron spectroscopy (XPS) and spectroscopic ellipsometry measurements are reported. Au and Si surfaces are amino-functionalized with self-assembled monolayers (SAMs) of cystamine and 3-aminopropyldimethyethoxysilane (APDMES), respectively. Maltoheptaose is covalently attached to the amino-functionalized Au and Si surfaces via reductive amination. Amylose brushes are grown from maltoheptaose modified Au and Si surfaces with enzymatic polymerization using potato phosphorylase and Rabbit Muscle phosphorylase, as evidenced by spectroscopic ellipsometry and XPS measurements.
Assuntos
Amilose/química , Glucanos/química , Amilose/síntese química , Técnicas de Química Sintética , Ouro , Fosforilases/química , Espectroscopia Fotoeletrônica , Polimerização , Silício , Análise Espectral , Propriedades de SuperfícieRESUMO
This work reports the synthesis of new polymer-titania hybrids, where the organic phase is constituted by polyesters such as poly(-caprolactone), poly(d,l-lactic acid), and poly(l-lactic acid). In these hybrids, very strong interaction between the organic and inorganic domains is obtained through transesterification of ester moieties by titanium atoms, which leads to organotitanium esters. The influence of the structure of the polyester on the mode of its interaction with titania is also investigated. Hybrids with a range of solid-state properties, which depend on the starting polymer characteristics and on the inorganic-phase content, are obtained. Hybrids are applied as coatings on a variety of substrates. They show intrinsic optical transparency and the ability to completely block UV radiation in the range UVB and UV-A2. In particular, when applied to different textiles, the hybrids impart radiopacity to the fabrics, opening new perspectives in the field of personal protective clothing and equipment.
Assuntos
Poliésteres/química , Roupa de Proteção , Proteção Radiológica/métodos , Titânio/química , Lesões por Radiação/prevenção & controle , Espectroscopia de Infravermelho com Transformada de Fourier , Raios Ultravioleta , Raios XRESUMO
Hybrid organic-inorganic nanocomposites were prepared starting from alpha,omega-triethoxysilane-terminated poly(d,l-lactic acid) (PDLLA) to be used as potential radiopaque biocompatible coatings for medical devices. The synthesis of the organic phase precursors of given chain length was achieved via anionic polymerization of d,l-lactide using a bifunctional initiator and subsequent triethoxysilane functionalization of the end groups. PDLLA-based ceramers (ceramic polymers) were then synthesized by the sol-gel process at room temperature (rt) in the presence of different amounts of tetraethoxysilane. The rt-synthesized hybrids were then cured (at 80 or 130 degrees C), and their thermal and viscoelastic properties were investigated. All obtained hybrids were optically transparent, due to the nanometric dimension of the silica particles, and yielded clearly contrasted radiographic images.