Lithium vanadium oxide (Li1.1V3O8) thick porous electrodes with high rate capacity: utilization and evolution upon extended cycling elucidated via operando energy dispersive X-ray diffraction and continuum simulation.

The phase distribution of lithiated LVO in thick (∼500 µm) porous electrodes (TPEs) designed to facilitate both ion and electron transport was determined using synchrotron-based operando energy dispersive X-ray diffraction (EDXRD). Probing 3 positions in the TPE while cycling at a 1C rate revealed a homogeneous phase transition across the thickness of the electrode at the 1st and 95th cycles. Continuum modelling indicated uniform lithiation across the TPE in agreement with the EDXRD results and ascribed decreasing accessible active material to be the cause of loss in delivered capacity between the 1st and 95th cycles. The model was supported by the observation of significant particle fracture by SEM consistent with loss of electrical contact. Overall, the combination of operando EDXRD, continuum modeling, and ex situ measurements enabled a deeper understanding of lithium vanadium oxide transport properties under high rate extended cycling within a thick highly porous electrode architecture.

(De)lithiation of spinel ferrites Fe3O4, MgFe2O4, and ZnFe2O4: a combined spectroscopic, diffraction and theory study.

Iron based materials hold promise as next generation battery electrode materials for Li ion batteries due to their earth abundance, low cost, and low environmental impact. The iron oxide, magnetite Fe3O4, adopts the spinel (AB2O4) structure. Other 2+ cation transition metal centers can also occupy both tetrahedral and/or octahedral sites in the spinel structure including MgFe2O4, a partially inverse spinel, and ZnFe2O4, a normal spinel. Though structurally similar to Fe3O4 in the pristine state, previous studies suggest significant differences in structural evolution depending on the 2+ cation in the structure. This investigation involves X-ray absorption spectroscopy and X-ray diffraction affirmed by density functional theory (DFT) to elucidate the role of the 2+ cation on the structural evolution and phase transformations during (de)lithiation of the spinel ferrites Fe3O4, MgFe2O4, and ZnFe2O4. The cation in the inverse, normal and partially inverse spinel structures located in the tetrahedral (8a) site migrates to the previously unoccupied octahedral 16c site by 2 electron equivalents of lithiation, resulting in a disordered [A]16c[B2]16dO4 structure. DFT calculations support the experimental results, predicting full displacement of the 8a cation to the 16c site at 2 electron equivalents. Substitution of the 2+ cation results in segregation of oxidized phases in the charged state. This report provides significant structural insight into the (de)lithiation mechanisms for an intriguing class of iron oxide materials.

Impact of Charge Voltage on Factors Influencing Capacity Fade in Layered NMC622: Multimodal X-ray and Electrochemical Characterization.

Ni-rich NMC is an attractive Li-ion battery cathode due to its combination of energy density, thermal stability, and reversibility. While higher delivered energy density can be achieved with a more positive charge voltage limit, this approach compromises sustained reversibility. Improved understanding of the local and bulk structural transformations as a function of charge voltage, and their associated impacts on capacity fade are critically needed. Through simultaneous operando synchrotron X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS) of cells cycled at 3-4.3 or 3-4.7 V, this study presents an in-depth investigation into the effects of voltage window on local coordination, bulk structure, and oxidation state. These measurements are complemented by ex situ X-ray fluorescence (XRF) mapping and scanning electrochemical microscopy mapping (SECM) of the negative electrode, X-ray photoelectron spectroscopy (XPS) of the positive electrode, and cell level electrochemical impedance spectroscopy (EIS). Initially, cycling between 3 and 4.7 V leads to greater delivered capacity due to greater lithium extraction, accompanied by increased structural distortion, moderately higher Ni oxidation, and substantially higher Co oxidation. Continued cycling at this high voltage results in suppressed Ni and Co redox, greater structural distortion, increased levels of transition metal dissolution, higher cell impedance, and 3× greater capacity fade.

Probing Kinetics of Water-in-Salt Aqueous Batteries with Thick Porous Electrodes.

Aqueous electrochemical systems suffer from a low energy density due to a small voltage window of water (1.23 V). Using thicker electrodes to increase the energy density and highly concentrated "water-in-salt" (WIS) electrolytes to extend the voltage range can be a promising solution. However, thicker electrodes produce longer diffusion pathways across the electrode. The highly concentrated salts in WIS electrolytes alter the physicochemical properties which determine the transport behaviors of electrolytes. Understanding how these factors interplay to drive complex transport phenomena in WIS batteries with thick electrodes via deterministic analysis on the rate-limiting factors and kinetics is critical to enhance the rate-performance in these batteries. In this work, a multimodal approach-Raman tomography, operando X-ray diffraction refinement, and synchrotron X-ray 3D spectroscopic imaging-was used to investigate the chemical heterogeneity in LiV3O8-LiMn2O4 WIS batteries with thick porous electrodes cycled under different rates. The multimodal results indicate that the ionic diffusion in the electrolyte is the primary rate-limiting factor. This study highlights the importance of fundamentally understanding the electrochemically coupled transport phenomena in determining the rate-limiting factor of thick porous WIS batteries, thus leading to a design strategy for 3D morphology of thick electrodes for high-rate-performance aqueous batteries.

Defect Control in the Synthesis of 2 D MoS2 Nanosheets: Polysulfide Trapping in Composite Sulfur Cathodes for Li-S Batteries.

One of the inherent challenges with Li-S batteries is polysulfide dissolution, in which soluble polysulfide species can contribute to the active material loss from the cathode and undergo shuttling reactions inhibiting the ability to effectively charge the battery. Prior theoretical studies have proposed the possible benefit of defective 2 D MoS2 materials as polysulfide trapping agents. Herein the synthesis and thorough characterization of hydrothermally prepared MoS2 nanosheets that vary in layer number, morphology, lateral size, and defect content are reported. The materials were incorporated into composite sulfur-based cathodes and studied in Li-S batteries with environmentally benign ether-based electrolytes. Through directed synthesis of the MoS2 additive, the relationship between synthetically induced defects in 2 D MoS2 materials and resultant electrochemistry was elucidated and described.

Systems-level investigation of aqueous batteries for understanding the benefit of water-in-salt electrolyte by synchrotron nanoimaging.

Water-in-salt (WIS) electrolytes provide a promising path toward aqueous battery systems with enlarged operating voltage windows for better safety and environmental sustainability. In this work, a new electrode couple, LiV3O8-LiMn2O4, for aqueous Li-ion batteries is investigated to understand the mechanism by which the WIS electrolyte improves the cycling stability at an extended voltage window. Operando synchrotron transmission x-ray microscopy on the LiMn2O4 cathode reveals that the WIS electrolyte suppresses the mechanical damage to the electrode network and dissolution of the electrode particles, in addition to delaying the water decomposition process. Because the viscosity of WIS is notably higher, the reaction heterogeneity of the electrodes is quantified with x-ray absorption spectroscopic imaging, visualizing the kinetic limitations of the WIS electrolyte. This work furthers the mechanistic understanding of electrode-WIS electrolyte interactions and paves the way to explore the strategy to mitigate their possible kinetic limitations in three-dimensional architectures.

Deliberate Modification of Fe3O4 Anode Surface Chemistry: Impact on Electrochemistry.

Fe3O4 nanoparticles (NPs) with an average size of 8-10 nm have been successfully functionalized with various surface-treatment agents to serve as model systems for probing surface chemistry-dependent electrochemistry of the resulting electrodes. The surface-treatment agents used for the functionalization of Fe3O4 anode materials were systematically varied to include aromatic or aliphatic structures: 4-mercaptobenzoic acid, benzoic acid (BA), 3-mercaptopropionic acid, and propionic acid (PA). Both structural and electrochemical characterizations have been used to systematically correlate the electrode functionality with the corresponding surface chemistry. Surface treatment with ligands led to better Fe3O4 dispersion, especially with the aromatic ligands. Electrochemistry was impacted where the PA- and BA-treated Fe3O4 systems without the -SH group demonstrated a higher rate capability than their thiol-containing counterparts and the pristine Fe3O4. Specifically, the PA system delivered the highest capacity and cycling stability among all samples tested. Notably, the aromatic BA system outperformed the aliphatic PA counterpart during extended cycling under high current density, due to the improved charge transfer and ion transport kinetics as well as better dispersion of Fe3O4 NPs, induced by the conjugated system. Our surface engineering of the Fe3O4 electrode presented herein, highlights the importance of modifying the structure and chemistry of surface-treatment agents as a plausible means of enhancing the interfacial charge transfer within metal oxide composite electrodes without hampering the resulting tap density of the resulting electrode.