RESUMO
This study investigates biochar as an attractive option for removing pharmaceuticals from wastewater streams utilizing data from various literature sources and also explores the sensitivity of the characteristics and implementation of biochar. ANN 1 was designed to determine the optimal biochar characteristics (Surface Area, Pore Volume) to achieve the maximum percentage removal of pharmaceuticals in wastewater streams. ANN 2 was developed to identify the optimal biomass feedstock composition, pyrolysis conditions (temperature and time), and chemical activation (acid or base) to produce the optimal biochar from ANN 1. ANN 3 was developed to investigate the effectiveness of the biochar produced in ANN 1 and 2 in removing dye from water. Biomass feedstock with a high lignin content and high volatile matter at a high pyrolysis temperature, whether using an acid or base, achieves a high mesopore volume and high surface area. The biochar with the highest surface area and mesopore volume achieved the highest removal percentage. Regardless of hydrophobicity conditions, at low dosages (0.2), a high surface area and pore volume are required for a high percent removal. And with a higher dosage, a lower surface area and pore volume is necessary to achieve a high percent removal.
Assuntos
Carvão Vegetal , Águas Residuárias , Carvão Vegetal/química , Redes Neurais de Computação , Tecnologia , Preparações Farmacêuticas , AdsorçãoRESUMO
A new adsorbent for removing copper ions from aqueous solutions has been developed and characterized. The present study deals with the sorption of Cu(II) from aqueous solution on chemically pretreated sodium carbonate-treated rice husk (SCRH). The physico-chemical characteristics of rice husks were investigated to analyze their suitability to adsorb Cu(II) ions from water and wastewater. The raw rice husk (RRH), SCRH and Cu(II) adsorbed rice husk were analyzed by SEM-EDAX analysis. FTIR spectroscopy was also applied to identify functional groups, capable of adsorbing metal ions. Batch kinetic studies were conducted for the adsorption of Cu(II) on SCRH. It has been observed that 92.9-96.0% removal of Cu(II) is achieved at 4.8 mg of Cu(II)/g of adsorbent, adsorbent dose of 10 g L-1 and initial Cu(II) concentration of 10 mg L-1 in a temperature range of 15-50 °C. It was observed that the adsorption of Cu(II) on SCRH followed pseudo second-order kinetic and time to achieve equilibrium was found to be 60 min. The maximum uptake (97%) of Cu (II) was observed at pH 6. In this paper, an attempt has also been made to develop simple and readily understandable thermodynamic parameters related to sorption process at the equilibrium for understanding the adsorption mechanism. The Gibbs free energy ΔG° values for the adsorption processes of Cu(II) at 15, 30, 40 and 50 °C were calculated as -6.16, -6.84, -8.01 and -8.53 kJ mol-1, respectively. The negative value of ΔG° indicates spontaneity of adsorption. The values of ΔH° and ΔS° for Cu(II) adsorption were calculated as 14.37 kJ mol-1 and 70.92 J K-1 mol-1, respectively. The activation energy for the adsorption of Cu(II) was found to be 9 kJ mol-1 which is a characteristic for diffusion limited processes.
Assuntos
Carbonatos/farmacologia , Cobre/isolamento & purificação , Oryza/efeitos dos fármacos , Oryza/metabolismo , Purificação da Água/métodos , Água/química , Adsorção , Biodegradação Ambiental , Biomassa , Carbonatos/química , Cobre/química , Cobre/farmacocinética , Difusão , Concentração de Íons de Hidrogênio , Cinética , Soluções , Termodinâmica , Poluentes Químicos da Água/isolamento & purificação , Poluentes Químicos da Água/farmacocinéticaRESUMO
Excessive contamination of fluoride in wastewater is the cause of several chronic health problems. For this purpose, an adsorbent was prepared from alumina by acidic activation using sulfuric acid. The current research aims to find the maximum fluoride adsorption (%) from synthetic and industrial wastewater at optimum process parameters by using response surface methodology (RSM). All batch scale experiments were carried out according to the statistical-design order. Central composite design (CCD) was applied to ascertain the effect of adsorbent dose, pH, initial fluoride concentration and temperature on fluoride adsorption (%). Maximum fluoride removal was predicted based on the quadratic model developed. Validation of the model was done with negligible error. The regression coefficient of the model was found to be 0.96. From the analysis of variance (ANOVA), the factors with the greatest effect on the adsorption of fluoride were identified. Under optimized condition, the adsorbent dose 13.89 g L-1, pH 5.52, temperature 25 °C and initial fluoride concentration 18.67 mg L-1 resulted in 96% of maximum fluoride adsorption. Under the same optimized parameters, the fluoride adsorption from industrial wastewater found to be 92.10%.
Assuntos
Óxido de Alumínio/química , Fluoretos/isolamento & purificação , Águas Residuárias/química , Purificação da Água/métodos , Ácidos/química , Adsorção , Óxido de Alumínio/metabolismo , Calibragem , Fluoretos/química , Fluoretos/farmacocinética , Concentração de Íons de Hidrogênio , Resíduos Industriais/análise , Propriedades de Superfície , Temperatura , Poluentes Químicos da Água/isolamento & purificação , Poluentes Químicos da Água/farmacocinética , Purificação da Água/normasRESUMO
In the present article, optimization of process variables has been done to maximize the removal efficiency of toxic HCl gas in a submerged self-priming venturi scrubber. Response surface methodology with central composite design has been chosen to predict the effect of process variables on the removal efficiency. A quadratic equation was found from this study to predict the removal efficiency and from the ANOVA test, the significance of process variables was evaluated. Regression analysis confirmed the suitability of the developed model by the higher R2 square value (0.9717). Optimum conditions were obtained as 55.18 m s-1 of throat gas velocity, 405.10 ppm of inlet HCl concentration and 0.0038 N of NaOH concentration in scrubbing liquid to achieve 90.80% of the HCl removal efficiency.
Assuntos
Poluentes Atmosféricos/análise , Recuperação e Remediação Ambiental/métodos , Ácido Clorídrico/análise , Modelos Teóricos , Análise de Variância , Recuperação e Remediação Ambiental/instrumentação , Desenho de Equipamento , Humanos , Análise de Regressão , Hidróxido de Sódio/químicaRESUMO
Excessive fluoride concentration in wastewater is a major health concern worldwide. The main objective of wastewater treatment is to allow industrial effluents to be disposed of without danger to the human health and the natural environment. In this current study, experiments have been conducted to remove fluoride from aqueous solution using alumina and HCl (Hydrochloric acid) treated activated alumina in a continuous mode. A spiral rib was introduced in the cylindrical part of the conventional hydrocyclone to increase the performance, and the new hydrocyclone is dubbed as ribbed hydrocyclone. Experiments were carried out to analyze the performance of the ribbed hydrocyclone and compared the results with the conventional hydrocyclone of the same dimension. The efficiency of conventional and ribbed hydrocyclone at a slurry flow rate of 50 LPM (liter per minute) for the solid concentration of 1.4 wt% were 80% and 93.5% respectively. The cut size d50 of the conventional and ribbed hydrocyclone was 18 µm and 13 µm respectively at a slurry velocity of 50 LPM. Fluoride removal efficiency using alumina and HCl-treated alumina was also investigated in a continuous mode by the ribbed hydrocyclone. Maximum fluoride removal efficiency was 49.5%, and 80% for alumina and HCl-treated alumina for the initial concentration of 10 mg/L at a slurry flow rate of 50 LPM.
Assuntos
Óxido de Alumínio/farmacocinética , Fluoretos/isolamento & purificação , Fluoretos/farmacocinética , Ácido Clorídrico/farmacologia , Águas Residuárias/química , Purificação da Água , Adsorção , Óxido de Alumínio/química , Humanos , Ácido Clorídrico/química , Concentração de Íons de Hidrogênio , Água/química , Poluentes Químicos da Água/isolamento & purificação , Poluentes Químicos da Água/farmacocinética , Purificação da Água/instrumentação , Purificação da Água/métodosRESUMO
The objective of this study was to observe the performance of a lab-scale three-stage dual-flow sieve plate column scrubber for hydrogen sulfide (H2S) gas removal from a gas stream, in which the H2S concentration was similar to that of gasifier syngas. The tap water was used as scrubbing liquid. The gas and liquid were operated at flow rates in the range of 16.59 × 10-4-27.65 × 10-4 Nm3/s and 20.649 × 10-6-48.183 × 10-6 m3/s, respectively. The effects of gas and liquid flow rates on the percentage removal of H2S were studied at 50-300 ppm inlet concentrations of H2S. The increase in liquid flow rate, gas flow rate and inlet H2S concentration increased the percentage removal of H2S. The maximum of 78.88% removal of H2S was observed at 27.65 × 10-4 Nm3/s gas flow rate and 48.183 × 10-6 m3/s liquid flow rate for 300 ppm inlet concentration of H2S. A model has also been developed to predict the H2S gas removal by using the results from the experiments and adding the parameters that affect the scrubber's performance. The deviations between experimental and predicted H2S percentage removal values were observed as less than 16%.
Assuntos
Poluentes Ocupacionais do Ar/isolamento & purificação , Recuperação e Remediação Ambiental , Sulfeto de Hidrogênio/isolamento & purificação , Modelos Teóricos , Recuperação e Remediação Ambiental/instrumentação , Recuperação e Remediação Ambiental/métodos , Desenho de EquipamentoRESUMO
The current study explores the co-pyrolysis of waste motor oil (WMO) and rice stubble in a designed lab-scale pyrolyzer to produce alternative energy fuels. The parameter screening was followed by optimization utilizing the Box-Behnken design (BBD). Reactor temperature (TR), mixing ratio (M), and holding time (t) affected the co-pyro-oil yield substantially. A maximum co-pyro-oil yield of 90.3% was achieved at a TR = 485 °C, t = 12.5 min, and M = 5% rice stubble to waste motor oil, which was further characterized and compared with the commercial diesel fuel properties. The highest research octane number of 76.15 was obtained for the co-pyro-oil (Co-PO), followed by the pyro-oil generated from only waste motor oil (POWMO). Consequently, the paraffin content increased to 64.34 wt% from 27.66 wt % for PO RS. The carbon number varied from C7-C17 for PO WMO and Co-Po, aligning with the diesel fuel requirements. Furthermore, a substantial enrichment in the physio-chemical properties of the produced Co-PO with reduced moisture content and enhancement in higher heating value (HHV) was also noticed. Hence, the generated Co-PO could be utilized as transport-grade fuel.
Assuntos
Oryza , Petróleo , Gasolina , Pirólise , ÓleosRESUMO
Solid waste is currently produced in substantial amounts by industrial activities. While some are recycled, the majority of them are dumped in landfills. Iron and steel production leaves behind ferrous slag, which must be created organically, managed wisely and scientifically if the sector is to remain more sustainably maintained. Ferrous slag is the term for the solid waste that is produced when raw iron is smelted in ironworks and during the production of steel. Both its specific surface area and porosity are relatively high. Since these industrial waste materials are so easily accessible and offer such serious disposal challenges, the idea of their reuse in water and wastewater treatment systems is an appealing alternative. There are many components such as Fe, Na, Ca, Mg, and silicon found in ferrous slags, which make it an ideal substance for wastewater treatment. This research investigates the potential of ferrous slag as coagulants, filters, adsorbents, neutralizers/stabilizers, supplementary filler material in soil aquifers, and engineered wetland bed media to remove contaminants from water and wastewater. Ferrous slag may provide a substantial environmental risk before or after reuse, so leaching and eco-toxicological investigations are necessary. Some study revealed that the amount of heavy metal ions leached from ferrous slag conforms to industrial norms and is exceedingly safe, hence it may be employed as a new type of inexpensive material to remove contaminants from wastewater. The practical relevance and significance of these aspects are attempted to be analyzed, taking into account all recent advancements in the fields, in order to help in the development of informed decisions about future directions for research and development related to the utilization of ferrous slags for wastewater treatment.
Assuntos
Águas Residuárias , Água , Resíduos Sólidos , Resíduos Industriais/análise , Ferro , AçoRESUMO
Simultaneous renewable energy generation is an imperative part of sustainable hazardous waste management. Therefore, the present work explicates the co-pyrolysis of rice stubble (RS) waste biomass and spent motor oil (SMO) to upgrade the obtained bio-oil. Moreover, two different modes, namely, in-situ and ex-situ, were implemented to analyze the effect of physical inhibition. Monothetic analysis approach was followed to determine optimum process conditions. A substantial increment of â¼ 85% was observed in bio-oil yield for RS: SMO (1:1) in-situ operation whilst the only RS biomass pyrolysis. Moreover, the HHV increased by â¼ 2.15 times after co-pyrolysis with a considerable reduction (62.70%) in water content. Consequently, the paraffin content increased to 79.14 vol% with an iso-paraffin index of 0.285. Subsequently, a possible reaction mechanism is also proposed to evaluate results comprehensively. Altogether, the co-pyrolysis of these feedstocks resulted in improved aliphatic content and reduced oxygenates, encouraging its adequacy as an alternate fuel.
Assuntos
Petróleo , Pirólise , Biocombustíveis , Biomassa , Catálise , Temperatura Alta , ParafinaRESUMO
In this study, catalytic urea hydrolysis for production of ammonia in presence of fly ash, at optimum condition, was investigated in a batch reactor. The single and combined effects of operating parameters such as initial feed concentrations, temperature, fly ash doses, times and stirring speed on the production of ammonia from urea were analyzed using response surface methodology. A 2(5) full factorial central composite experimental design was employed. Analysis of variance (ANOVA) showed a high coefficient of determination value (R(2)= 0.963) and satisfactory prediction second order regression model was derived. The optimum production conditions were determined as initial feed concentration 19.9 wt. % of urea, temperature 175°C, fly ash dose 7.5 g/L, reaction time 25 min and stirring speed 769 rpm. At optimum conversion conditions, the conversion of urea for production of ammonia was found to be 99.8 %.
Assuntos
Amônia/síntese química , Cinza de Carvão/química , Centrais Elétricas , Ureia/química , Catálise , Hidrólise , Análise Multivariada , Análise de RegressãoRESUMO
The excess amount of fluoride contamination in the groundwater or industrial effluents fosters various health problems. Considering the advantages of adsorption, the current research reports the synthesis of a novel adsorbent (HNAA) by simple and convenient process of nitric acid activation of alumina. The physiochemical characterization (SEM, EDX, XRF, FTIR, BET, and pHZPC) results exhibited successful activation of alumina and adsorption of fluoride ions. The effect of process parameters (contact time, initial pH, adsorbent dose, initial fluoride concentration and presence of coexisting ions) on adsorption of fluoride ions on HNAA were investigated in batch scale. The adsorption of fluoride ion on HNAA followed the Freundlich isotherm and pseudo second order kinetic model. The Qmax of HNAA adsorbent was 45.75â¯mg/g at 45⯰C. The fluoride ion adsorption was revealed to be endothermic and spontaneous. The experimentation of the HNAA adsorbent on industrial wastewater, with fluoride concentration of 17.5â¯mg/L, inferred the significant defluoridation potential at the optimized adsorbent dose and pH. The nitric acid activation of alumina resulted in improvement of defluoridation efficiency from 74.18% to 97.43%. The HNAA also exhibited the better regeneration and reusability features which distinguish it as a promising adsorbent to be applied for real field wastewater.
RESUMO
The excessive release of wastewater into the environment is a major concern worldwide. Adsorption is the one of the most effective technique for treatment of wastewater. In this work activated carbon prepared from rice husk has been used as an adsorbent. In the present investigation a three phase modified multi-stage bubble column reactor (MMBCR) has been designed to remove lead and biochemical oxygen demand (BOD) from wastewater by means of its adsorption onto the surface of activated rice husk. The multi-staging has been achieved by hydrodynamically induced continuous bubble generation, breakup and regeneration. Under optimum conditions, maximum lead and BOD reduction achieved using activated rice husk was 77.15% and 19.05%, respectively. Results showed MMBCR offered appreciated potential benefits for lead removal from wastewater and BOD removal, even this extent of removal is encouraging and the MMBCR can be used a pretreatment unit before subjecting the wastewater to biological treatment.
Assuntos
Reatores Biológicos , Chumbo/isolamento & purificação , Chumbo/metabolismo , Oryza/metabolismo , Consumo de Oxigênio , Poluentes Químicos da Água/isolamento & purificação , Poluentes Químicos da Água/metabolismo , Adsorção , Gases/química , Eliminação de Resíduos LíquidosRESUMO
Excessive fluoride contamination in ground and surface water is hazardous to human health. Adsorptive removal is a better option for defluoridation due to its simplicity and efficient working property. In the current research, an attempt was made for the removal of fluoride ions from wastewater by a novel adsorbent synthesized with alumina and H2SO4 acid by acidic activation. The adsorbent was characterized for physio-chemical properties by several analytical methods (SEM, EDX, FTIR, XRF, TGA, XRD, HI and pHZPC). The specific surface area of acid activated alumina (AAA) adsorbent was found to be 87.44 m2/g. The batch scale experiments were conducted to study the effect of initial pH, adsorbent dose, stirring rate, and contact time on the defluoridation efficiency of AAA adsorbent. The experimental data of isotherm study was found to follow the Freundlich isotherm model. The maximum adsorption capacity of fluoride on AAA was 69.52 mg/g at 318 K. The nature of adsorption was found to be endothermic and spontaneous. The adsorption kinetic data followed the pseudo-second-order model. The fluoride removal efficiency of alumina with and without acid activation resulted in 96.72% and 63.58%, respectively. The regeneration capability, reusability, applicability on industrial effluent and economic value were investigated.
RESUMO
Growing concern about the effect of hydrochloric acid gas (HCl) on environment and abatement of it is now a very serious issue. This present paper is focused on developing a realistic model in order to remove the HCl from the off gases using self-priming venturi scrubber. A detailed parametric study of throat gas velocity (36-72â¯m/s), liquid level in outer cylinder (0.40-0.77â¯m) and inlet concentration of HCl (100-500â¯ppm) on HCl removal efficiency have been done with normal water as a scrubbing liquid. Also the removal efficiency was enhanced by using NaOH solution as a scrubbing liquid in submerged and non-submerged conditions. Therefore, the maximum removal efficiency of HCl was obtained as 87.83% with normal water and 92.54% with 0.005N NaOH solution as the scrubbing liquid at inlet HCl concentration of 500â¯ppm, throat gas velocity of 60â¯m/s and liquid level of 0.77â¯m in submerged condition. Experimental results were validated with the developed empirical model and showed excellent agreement with less deviation.
RESUMO
The excessive release of color into the environment is a major concern worldwide. Adsorption process is among the most effective techniques for color removal from wastewater and fly ash has been widely used as an adsorbent. Therefore, this study was carried out to understand the adsorption behavior of methylene blue from aqueous systems onto fly ash using the continuous mode. Continuous mode sorption experiments were carried out to remove methylene blue from its aqueous solutions in hydrocyclone equipment. The experiments were performed at constant temperature and dimensions of hydrocyclone with variation of flows through the equipment, concentrations of methylene blue solutions and fly ash concentration, respectively. A maximum removal of 58.24% was observed at adsorbent dosage of 900 mg/l at pH 6.75 for an initial methylene blue concentration of 65 mg/l.
Assuntos
Carbono/química , Azul de Metileno/isolamento & purificação , Material Particulado/química , Poluentes Químicos da Água/isolamento & purificação , Adsorção , Cinza de Carvão , Tamanho da PartículaRESUMO
The low-cost activated carbon were prepared from Tamarind wood material by chemical activation with sulphuric acid for the adsorption of Pb(II) from dilute aqueous solution. The activated carbon developed shows substantial capacity to adsorb Pb(II) from dilute aqueous solutions. The parameters studied include physical and chemical properties of adsorbent, pH, adsorbent dose, contact time and initial concentrations. The kinetic data were best fitted to the Lagergren pseudo-first-order and pseudo-second order models. The isotherm equilibrium data were well fitted by the Langmuir and Freundlich models. The maximum removal of lead(II) was obtained 97.95% (experimental) and 134.22 mg/g (from Langmuir isotherm model) at initial concentration 40 mg/l, adsorbent dose 3g/l and pH 6.5. This high uptake showed Tamarind wood activated carbon as among the best adsorbents for Pb(II).
Assuntos
Chumbo/química , Tamarindus , Eliminação de Resíduos Líquidos/métodos , Poluentes Químicos da Água/química , Purificação da Água/métodos , Madeira/química , Carbono/química , Ácidos Sulfúricos/químicaRESUMO
The excessive release of lead from lead acid batteries, smelting plant into the environment is a major concern worldwide. Adsorption process is among the most effective techniques for lead removal from wastewater and activated carbon has been widely used as an adsorbent. In this paper an attempt has been made to investigate the adsorption behaviour of Pb(II) from aqueous systems onto granular activated carbon using the batch mode and continuous mode in a packed bed column with more successive service and regeneration. The experiments were performed at constant temperature and dimensions of column and packed bed of granular activated carbon with variation of flows through the bed and concentrations of lead solutions. Breakthrough points were found out for the adsorption of lead on the adsorbent using continuous-flow column operation by varying different operating parameters like hydraulic loading rate from 4 to 16 m(3)/h m(2) and feed concentrates from 20 to 60 mg/l. Granular activated carbon column regeneration using 0.5 M concentration of HNO(3) has been investigated. Results indicate encouraging performance towards removal of Pb(II).
Assuntos
Carbono/química , Chumbo/isolamento & purificação , Adsorção , Espectroscopia de Infravermelho com Transformada de FourierRESUMO
Indian high-ash coal contains alpha-silica components of the mineral matter. When coal is transported in the form of a slurry, alpha-silica adds to the settling properties of coal and enhances erosion of pipelines. As such any technique that will contribute to changing the characteristics of mineral matter by selective demineralization is bound to supplement the knowledge of coal slurries in the science of rheology. One such method is the use of a novel microwave technology, which changes the alpha-silica to less harmful beta-silica. Thus microwave-treated coal slurry facilitates enhanced flow characteristics and abates the erosion problem in pipeline transport as well as in coal-slurry injection furnaces. This paper reports on the rheological study of closely sized coal particles of medium-volatile, low-ash, low-moisture cleans and high-ash rejects with and without microwave treatment. Viscosity of suspensions of microwave-treated coal was found to be less than that of untreated coal, in the case of both cleans and rejects. Microwave pretreatment thus reduces the viscosity and the pumping cost and opens a new outlook for pipeline transport. An attempt has been made to quantify the improvement of rheological characteristics due to microwave pretreatment.
RESUMO
A bubbling counter-current multistage fluidized bed reactor for the sorption of carbon dioxide (CO(2)) by hydrated lime particles was simulated employing a two-phase model, with the bubble phase assumed to be in plug flow, and the emulsion phase in plug flow and perfectly mixed flow conditions. To meet prescribed permissible limit to emit carbon dioxide from industrial flue gases, dry scrubbing of CO(2) was realized. For the evaluation, a pilot plant was built, on which also the removal efficiency of CO(2) was verified at different solids flow rates. The model results were compared with experimental data in terms of percentage removal efficiency of carbon dioxide. The comparison showed that the EGPF model agreed well with the experimental data satisfactorily. The removal efficiency was observed to be mainly influenced by flow rates of adsorbent and CO(2) concentration.
Assuntos
Dióxido de Carbono/química , Modelos Teóricos , GasesRESUMO
The low-cost activated carbon was prepared from Tamarind wood an agricultural waste material, by chemical activation with zinc chloride. Activated carbon adsorption is an effective means for reducing organic chemicals, chlorine, heavy metals and unpleasant tastes and odours in effluent or colored substances from gas or liquid streams. Central composite design (CCD) was applied to study the influence of activation temperature, chemical ratio of zinc chloride to Tamarind wood and activation time on the chemical activation process of Tamarind wood. Two quadratic models were developed for yield of activated carbon and adsorption of malachite green oxalate using Design-Expert software. The models were used to calculate the optimum operating conditions for production of activated carbon providing a compromise between yield and adsorption of the process. The yield (45.26 wt.%) and adsorption (99.9%) of the activated carbon produced at these operating conditions showed an excellent agreement with the amounts predicted by the models.