RESUMO
The use of ordnance gelatine has been widespread in the field of ballistics as a simulant for soft tissue when assessing ballistic threats. However, the traditional method of preparing ordnance gelatine is time-consuming and requires precision to ensure that the final mold meets the required specifications. Furthermore, temperature control is necessary post-production, and there are limitations on its usage duration. To address these issues, manufacturers have developed pre-mixed, gelatine-like products that are stable at room temperature and require less preparation time. Nonetheless, it is uncertain whether these new products can perform in the same manner as the gold standard of ordnance gelatine. This study used five types of blocks, including ordnance gelatine (10% and 20%), Clear Ballistics (10% and 20%) and Perma-Gel (10%) and subjected them to 9 mm, 0.380 Auto fired from a universal receiver and a 5.56 × 45 mm ammunition fired by a certified firearms instructor. Delta-V and total energy dissipation were measured after each test using data collected from ballistic chronographs placed in front of and behind each block. High-speed video was recorded, and a cut-down analysis conducted. The findings revealed variations in energy dissipation and fissure formation within the block, with greater energy based on fissure formation observed in the ordnance gelatine. Additionally, the high-speed video showed the occurrence of secondary combustions occurring in the premixed gelatines.
Assuntos
Balística Forense , Gelatina , Ferimentos por Arma de Fogo , Balística Forense/métodos , Humanos , Modelos BiológicosRESUMO
BACKGROUND: The programmable intermittent epidural bolus (PIEB) has been popularized as the optimal delivery technique for labor analgesia. Suggested advantages of this method are less local anesthetic consumption, improved maternal satisfaction, potentially shorter duration of labor, and decreased workload requirements for the anesthesia providers. However, a manual bolus is still routinely used for breakthrough pain when the PIEB is underperforming. METHODS: We conducted a laboratory-based study to quantify the flow through a multiorifice epidural catheter using the PIEB setting on an epidural pump compared to the manual epidural bolus. Four syringe volumes, 3, 5, 10, and 20 mL, were selected for this experiment. The flow in a manual bolus was also studied with and without the presence of an epidural catheter filter. A generalized estimating equation analysis was done to compare data between the groups. RESULTS: Regardless of the syringe size, there was a several-fold increase in flow when a manual bolus was used compared to a pump-administered dose, with the highest difference in the peak flow rate observed in 3-mL boluses with up to a 12-fold difference, while the difference was, at most, 7-fold in 5-mL and 10-mL boluses. Manual boluses without a filter achieve a mean peak flow rate higher than manual boluses with a filter. CONCLUSIONS: Our study found that manual boluses produced a higher flow rate compared to the CADD-Solis epidural pump (Smiths Medical). This study also found that the placement of a particulate filter reduces the flow rates generated while bolusing. Bulk flow rate is directly correlated with induced pressure and solution spread. Because higher bolus pressure has been shown to provide a more efficient distribution of local anesthetic and more efficient pain relief, these results may have impactful clinical significance and will pave the way for future studies.
Assuntos
Analgesia Epidural , Analgesia Obstétrica , Anestesia Epidural , Feminino , Humanos , Anestésicos Locais , Analgesia Epidural/métodos , Manejo da Dor , Analgesia Controlada pelo Paciente , Catéteres , Analgesia Obstétrica/métodosRESUMO
Pulsatile arterial blood flow plays an important role in vascular system mechanobiology, especially in the study of mechanisms of pathology. Limitations in cost, time, sample size, and control across current in-vitro and in-vivo methods limit future exploration of novel treatments. Presented is the verification of a novel reciprocating positive displacement pump aimed at resolving these issues through the simulation of human ocular, human fingertip and skin surface, human cerebral, and rodent spleen organ systems. A range of pulsatile amplitudes, frequencies, and flow rates were simulated using pumps made of 3D printed parts incorporating a tubing system, check valve and proprietary software. Volumetric analysis of 430 total readings across a flow range of 0.025ml/min to 16ml/min determined that the pump had a mean absolute error and mean relative error of 0.041 ml/min and 1.385%, respectively. Linear regression analysis compared to expected flow rate across the full flow range yielded an R2 of 0.9996. Waveform analysis indicated that the pump could recreate accurate beat frequency for flow ranges above 0.06ml/min at 70BPM. The verification of accurate pump output opens avenues for the development of novel long-term in-vitro benchtop models capable of looking at fluid flow scenarios previously unfeasible, including low volume-high shear rate pulsatile flow.
Assuntos
Coração Auxiliar , Modelos Cardiovasculares , Humanos , Fluxo Pulsátil , Desenho de Equipamento , Simulação por ComputadorRESUMO
BACKGROUND: The flow of physiologic fluids through organs and organs systems is an integral component of their function. The complex fluid dynamics in many organ systems are still not completely understood, and in-vivo measurements of flow rates and pressure provide a testament to the complexity of each flow system. Variability in in-vivo measurements and the lack of control over flow characteristics leave a lot to be desired for testing and evaluation of current modes of treatments as well as future innovations. In-vitro models are particularly ideal for studying neurological conditions such as hydrocephalus due to their complex pathophysiology and interactions with therapeutic measures. The following aims to present the reciprocating positive displacement pump, capable of inducing pulsating flow of a defined volume at a controlled beat rate and amplitude. While the other fluidic applications of the pump are currently under investigation, this study was focused on simulating the pulsating cerebrospinal fluid production across profiles with varying parameters. METHODS: Pumps were manufactured using 3D printed and injection molded parts. The pumps were powered by an Arduino-based board and proprietary software that controls the linear motion of the pumps to achieve the specified output rate at the desired pulsation rate and amplitude. A range of 0.01 [Formula: see text] to 0.7 [Formula: see text] was tested to evaluate the versatility of the pumps. The accuracy and precision of the pumps' output were evaluated by obtaining a total of 150 one-minute weight measurements of degassed deionized water per output rate across 15 pump channels. In addition, nine experiments were performed to evaluate the pumps' control over pulsation rate and amplitude. RESULTS: Volumetric analysis of a total of 1200 readings determined that the pumps achieved the target output volume rate with a mean absolute error of -0.001034283 [Formula: see text] across the specified domain. It was also determined that the pumps can maintain pulsatile flow at a user-specified beat rate and amplitude. CONCLUSION: The validation of this reciprocating positive displacement pump system allows for the future validation of novel designs to components used to treat hydrocephalus and other physiologic models involving pulsatile flow. Based on the promising results of these experiments at simulating pulsatile CSF flow, a benchtop model of human CSF production and distribution could be achieved through the incorporation of a chamber system and a compliance component.