Electrochemical tuning of capacitive response of graphene oxide.

The increasing energy demands of modern society require a deep understanding of the properties of energy storage materials, as well as the tuning of their performance. We show that the capacitance of graphene oxide (GO) can be precisely tuned using a simple electrochemical reduction route. In situ resistance measurements, in combination with cyclic voltammetry measurements and Raman spectroscopy, have shown that upon reduction GO is irreversibly deoxygenated, which is further accompanied by structural ordering and an increase in electrical conductivity. The capacitance is maximized when the concentration of oxygen functional groups is properly balanced with the conductivity. Any further reduction and deoxygenation leads to a gradual loss of capacitance. The observed trend is independent of the preparation route and the exact chemical and structural properties of GO. It is proposed that an improvement in the capacitive properties of any GO can be achieved by optimization of its reduction conditions.

Ionic Referencing in Surface Plasmon Microscopy: Visualization of the Difference in Surface Properties of Patterned Monomolecular Layers.

An approach for visualization of patterned monomolecular layers in surface plasmon microscopy (SPM) is suggested. The development of hidden image in SPM is achieved by referencing of images obtained in the presence of electrolytes with a high molar refraction of either anions or cations. A formation of diffuse layer near the charged surface areas leads to the redistribution of ions. The ratio of SPM images allows one to visualize this redistribution and to distinguish surface areas with different properties. The approach is unobtrusive and robust; it can be used with most surface plasmon resonance (SPR) imaging instruments.

The Role of Anion Adsorption in the Effect of Electrode Potential on Surface Plasmon Resonance Response.

Surface plasmon resonance, being widely used in bioanalytics and biotechnology, is influenced by the electrical potential of the resonant gold layer. To evaluate the mechanism of this effect, we have studied it in solutions of various inorganic electrolytes. The magnitude of the effect decreases according to the series: KBr>KCl>KF>NaClO4 . The data were treated by using different models of the interface. A quantitative description was obtained for the model, which takes into account the local dielectric function of gold being affected by the free electron charge, diffuse ionic layer near the gold/water interface, and specific adsorption of halides to the gold surface with partial charge transfer. Taking into account that most biological experiments are performed in chloride-containing solutions, detailed analysis of the model at these conditions was performed. The results indicate that the chloride adsorption is the main mechanism for the influence of potential on the surface plasmon resonance. The dependencies of surface concentration and residual charge of chloride on the applied potential were determined.

Detection and Quantification of Single Engineered Nanoparticles in Complex Samples Using Template Matching in Wide-Field Surface Plasmon Microscopy.

An ultrasensitive analytical method for direct detection of single nanoparticles in complex environment is described. The method relies on the wide-field surface plasmon microscopy (SPM). The suppression of matrix effects is achieved by image analysis based on the template matching. First, characteristic SPM images of nanoparticles are collected in aqueous suspensions. Then the detection of nanoparticles in complex environment is performed using template matching. Quantification and characterization of nanoparticles size was demonstrated at subppb level (∼100 pg/mL) in such complex media as wines, fruit juices, or cosmetic formulation. Visualization of the nanoparticles is performed in real time. The method does not require any sample pretreatment. If the minimally acceptable adsorption rate is defined as one nanoparticle to the whole sensor surface per few seconds, the working range of the method is ∼106 to 1010 nanoparticles per mL.

Electrically controlled variation of receptor affinity.

A concept of virtual sensor array based on electrically controlled variation of affinity properties of the receptor layer is described. It was realized on the base of integrated electrochemical chemotransistor containing polyaniline as the receptor layer. Electrical control of the redox state of polyaniline was performed in five-electrode configuration containing four electrodes for conductivity measurements and one Ag/AgCl reference electrode. All the electrodes were integrated on the same glass chip. A room-temperature ionic liquid was used for the electrical connection between the reference electrode and chemosensitive material. Conductivity measurements demonstrated effective potential-controlled electrochemical conversions of the receptor material between different redox states. Binding of trimethylamine at three different potentials, corresponding to the different states of the receptor material, was studied. Concentration dependencies and binding kinetics were analyzed. The results demonstrated that the kinetic as well as the equilibrium binding properties of the receptor layer can be controlled by electrical potential, thus providing a possibility to form a virtual sensor array using only a single sensing element. Graphical abstract Single sensing element with electrical control of its affinity can operate as a virtual sensor array.

Individual Detection and Electrochemically Assisted Identification of Adsorbed Nanoparticles by Using Surface Plasmon Microscopy.

The increasing production and application of nanoparticles necessitates a highly sensitive analytical method for the quantification and identification of these potentially hazardous materials. We describe here an application of surface plasmon microscopy for the individual detection of each adsorbed nanoparticle and for visualization of its electrochemical conversion. Whereas the adsorption rate characterizes the number concentration of nanoparticles, the potential at which the adsorbed nanoparticles disappear during an anodic potential sweep characterizes the type of material. All the adsorbed nanoparticles are subjected to the potential sweep simultaneously; nevertheless, each of the up to a million adsorbed nanoparticles is identified individually by its electrochemical dissolution potential. The technique has been tested with silver and copper nanoparticles, but can be extended to many other electrochemically active nanomaterials.

Chemosensitive Properties of Electrochemically Synthesized Poly-3-Thienylboronic Acid: Conductometric Detection of Glucose and Other Diol-Containing Compounds under Electrical Affinity Control.

Due to the presence of the boronic acid moieties, poly-3-thienylboronic acid has an affinity for saccharides and other diol-containing compounds. Thin films of this novel chemosensitive polymer were synthesized electrochemically on the gold surface. The adhesion of the polymer was enhanced by the deposition of a monomolecular layer of thiophenol. The technology was used to fabricate conductometric sensors for glucose and other diol-containing compounds. Simultaneous two- and four-electrode conductivity measurements were performed. The chemical sensitivity to sorbitol, fructose, glucose, and ethylene glycol was studied at different pH and electrode potentials, and the corresponding binding constants were obtained. Depending on the electrode potential, the reciprocal values of the binding constants of glucose to poly-3-thienylboronic acid at neutral pH are in the range of 0.2 mM-1.0 mM. The affinity for glucose has been studied in buffer solutions and in solutions containing the major components of human blood. It was shown that the presence of human serum albumin increases the affinity of poly-3-thienylboronic acid for diol-containing compounds.

Agglomeration compaction promotes corrosion of gold nanoparticles.

Engineered nanoparticles are increasingly being used in various areas of human activity. However, the degradation mechanism of nanobodies in harsh environments is still a puzzle for theory and experiment. We report here the results of optical spectroscopy and nanoparticle tracking analysis, quantifying agglomeration and sizing of 50 nm citrate stabilized gold nanoparticles (GNPs) in HCl solutions containing H2O2. The mechanism of a consecutive corrosion reaction of GNPs is discussed within the framework of the near-field approach. We found that the disappearance of single nanoparticles from a suspension does not occur due to their dissolution per se, but is a consequence of the formation of aggregates. The neutralization of electrostatic shielding at high ionic strength allows gold nanoparticles to approach the subnanometer distance within the region of capping defects, at which the Casimir and van der Waals attractive forces dominate. It is suggested that electric field fluctuations in the confined space between highly conductive gold nanoparticles cause complexant-stimulated loss of metal from the core in the contact area. Going beyond the charge screening limitations by constraining the reaction space and reducing the double electrical layer thickness allows for chemical processes flow along otherwise not accessible reaction pathways.

Quantitative turbidity assay for lipolytic enzymes in microtiter plates.

A clearing assay for lipolytic enzymes has been realized in 96-well microtiter plates. A thin layer containing emulsified tributyrin as turbidity-generating substrate was placed on a thicker supporting aqueous layer. Both layers were stabilized by a gel-forming agent. Enzyme addition leads to clearing of the emulsion detected with a standard microtiter plate reader as a decrease of extinction. Dependencies of the signal kinetics on the substrate and enzyme concentrations were studied. For 0.5-1% tributyrin content the reaction rate is not substrate-limited. An initial slope of the signal kinetics is proportional to the lipase activity. A detailed characterization of the assay was performed. Lipolysis of tributyrin was confirmed by glycerol detection. Various gel-forming agents were compared and diffusion conditions in these gels were analyzed. Agar and agarose were found to be the most suitable gel-forming agents, which do not affect enzyme diffusion whereas polyacrylamide gels block lipase diffusion and therefore are not suitable for the assay. The optimized assay prepared from 1% tributyrin emulsion in 2% agar gel was tested with six microbial lipases and porcine pancreatic lipase. The detection limit is 20-60 ng/well which is equivalent to 30 µU/well for T. lanuginosus lipase.

A review of optical methods for ultrasensitive detection and characterization of nanoparticles in liquid media with a focus on the wide field surface plasmon microscopy.

Development of nanotechnology and corresponding industries during the last decade resulted in a new challenge for analytical science. This includes an ultrasensitive detection and characterization of nanoparticles of different origin and other nanomaterials in various media, including so complex ones as food, biological or environmental samples. The goal of this review is a systematic analysis of possible approaches and description of physical principles behind these methods. The main attention is paid to optical methods which are considered by authors to be mostly effective for the formulated task. Different approaches for detection and analysis of nanoparticles in a volume as well as of those adsorbed on a surface are discussed. While the technologies based on direct analysis of nanoparticle suspensions belong to the established approaches whose development potential has been in large extent exhausted, the novel technologies based on the surface sensing of adsorbed nanoparticles demonstrate intensive development. Therefore, the final part of the review is focused on the wide-field surface plasmon resonance microscopy. It allows one an ultrasensitive detection and characterization of individual nanoparticles of different origin in complex media and provides numerous possibilities for subsequent chemical identification of the detected particles using a hyphenation with other analytical technologies.

Analytical applications of electrodes modified by gold nanoparticles: dopamine detection.

Dopamine oxidation was studied on modified gold (nano-Au) electrodes obtained by Layer-by-Layer deposition of gold nanoparticles and polyacrylic acid. A gradual loss of electrochemical activity for the dopamine oxidation reaction is observed at pH 7. Simultaneous SPR spectroscopy and cyclic voltammetry indicate the formation of an adsorbed layer on the electrode surface at this pH value. Investigations, performed through electrochemical and SPR measurements at pH 4, give evidence for a reversible process. At this pH value both dopamine oxidation and reduction current peaks show linear dependence on the dopamine concentration and may be used for analytical applications. The use of the nano-Au electrode allows resolving the peaks corresponding to ascorbic acid and to dopamine oxidation by 240 mV thus providing a high selectively for dopamine detection in the presence of ascorbic acid. The detection limit of this electrode for dopamine is below 4 microM in the presence of 1 mM ascorbic acid. The sensitivity normalized to the macroscopic electrode surface is about 10 mA cm(-2) mM(-1) at sweep rate of 10 V/s.

Anomalous adsorptive properties of HIV protease: indication of two-dimensional crystallization?

Adsorption of HIV protease onto surfaces that are usually considered to be protein-resistant was studied quantitatively using surface plasmon resonance. Adsorption onto gold surfaces functionalized by OH-terminated alkyl chains was much stronger than onto oligo(ethylene glycol)-terminated surfaces. Equilibrium and kinetic adsorption constants were determined. An anomalous mutual attraction between adsorbate molecules was observed, indicating the possibility of two-dimensional crystallization of HIV protease. These results are applicable for the design of sensors/biosensors for HIV protease resistance detection and for proper manipulation of this enzyme in laboratory devices.

Noise reduction by multiple referencing in surface plasmon resonance imaging.

The analytical performance of surface plasmon resonance imaging with charge coupled device detection can be improved significantly by splitting a macroscopic sensing surface into multiple microscopic neighboring sensing and referencing subareas. It is shown that such a multiple referencing reduces intensity fluctuations across the total sensing area and, therefore, improves the signal/noise (S/N) ratio proportional to the splitting factor. The approach is demonstrated by detection of biotin binding to a monolayer of streptavidin. An effective variation of the reflected intensity of about 10(-4), which corresponds to the refraction index variation of 3x10(-6), was detected with a S/N ratio about 10 without any temperature stabilization of the sensing area.

Electrically controlled Michael addition: Addressing of covalent immobilization of biological receptors.

Electrically addressed covalent immobilization of biomolecules to the defined electrodes of an electrode array is described. It is based on Michael addition of the thiol group of biomolecules to α,ß-unsaturated carbonyl groups of benzoquinone. This "click" reaction was tested by immobilization of a number of thiolated compounds on the simplest array consisting of two gold electrodes coated by a self-assembled monolayer of benzoquinone-terminated hexanethiol. Electrically controlled binding of hexanethiol, ferrocenylhexanethiol, human serum albumin and thiol-terminated single-stranded DNA (ssDNA) was investigated. The binding was studied using cyclic voltammetry, X-ray photoelectron spectroscopy and surface plasmon resonance. The reaction requires the oxidized state of the benzoquinone moiety; this can be reached by applying of a moderate anodic potential to the electrode. Surface plasmon resonance measurements demonstrated that the thiol-modified ssDNA immobilized by this technique binds complementary synthetic oligonucleotides or PCR-amplified DNA fragments. The developed technology of electrical addressing of covalent immobilization can be applied for fabrication of sensor arrays.

Electrocatalytic activity of DNA on electrodes as an indication of hybridisation.

Electron transfer between metal electrodes and ferro/ferricyanide is completely suppressed at low ionic concentration. We describe here a new phenomenon related to this reaction: an immobilisation of thiolated single-stranded DNA on gold electrodes retains this activity at low ionic strength up to the level corresponding to the high ionic strength. In contrast, a hybridisation of the complementary DNA with the thiolated single-stranded DNA followed by a binding onto the electrodes, attenuated the electrocatalytic effect. These effects can be used for discrimination between single-stranded DNA and double-stranded DNA and for semi-quantitative measurement of complementary DNA in a sample.

Plasmonic detection and visualization of directed adsorption of charged single nanoparticles to patterned surfaces.

It has recently been shown that surface plasmon microscopy (SPM) allows single nanoparticles (NPs) on sensor surfaces to be detected and analyzed. The authors have applied this technique to study the adsorption of single metallic and plastic NPs. Binding of gold NPs (40, 60 and 100 nm in size) and of 100 nm polystyrene NPs to gold surfaces modified by differently ω-functionalized alkyl thiols was studied first. Self-assembled monolayers (SAM) with varying terminal functions including amino, carboxy, oligo(ethylene glycol), methyl, or trimethylammonium groups were deposited on gold films to form surfaces possessing different charge and hydrophobicity. The affinity of NPs to these surfaces depends strongly on the type of coating. SAMs terminated with trimethylammonium groups and carboxy group display highly different affinity and therefore were preferred when creating patterned charged surfaces. Citrate-stabilized gold NPs and sulfate-terminated polystyrene NPs were used as negatively charged NPs, while branched polyethylenimine-coated silver NPs were used as positively charged NPs. It is shown that the charged patterned areas on the gold films are capable of selectively adsorbing oppositely charged NPs that can be detected and analyzed with an ~1 ng⋅mL-1 detection limit. Graphical abstractSelf-assembled monolayers of ω-functionalized alkyl thiols were deposited on a gold layer of a patterned sensor array. The charge-selective binding of single nanoparticles to such surfaces was registered by wide-field surface plasmon microscopy.

A simple strategy for preparation of sensor arrays: molecularly structured monolayers as recognition elements.

The spreader-bar approach is a simple method for producing a huge variety of receptors with different selectivities. A sensor-array consisting of five such receptors is presented. A pattern recognition provides selective detection of different purines and pyrimidines.

Electroanalytical measurements without electrolytes: conducting polymers as probes for redox titration in non-conductive organic media.

Electroanalytical methods have been applied only in conducting media. An application of conducting polymers allows to overcome this limitation. If such material is in electrochemical equilibrium with dissolved redox active species, its electrical conductivity depends on the redox potential of these species. Therefore, conductometric measurements with conducting polymers can provide about the same information as classical redox electrodes. The approach was applied for redox titration. Equivalent points obtained by this titration in aqueous and organic electrolytes were identical. Then the approach was applied for determination of bromine number by redox titration in non-conducting organic phase.

Chemiresistors based on conducting polymers: a review on measurement techniques.

This review covers the development of measurement configurations for chemiresistors based on conducting polymers. The simplest chemiresistors are based on application of a two-electrode technique. Artifacts caused by contact resistance can be overcome by application of a four-electrode technique. Simultaneous application of the two- and four-electrode measurement configurations provides an internal control of sensor integrity. An incorporation of two additional electrodes controlling the redox state of chemosensitive polymers and connecting to the measurement electrodes through liquid or (quasi)solid electrolyte results in a six-electrode technique; an electrically driven regeneration of such sensors allows one to perform fast and completely reversible measurements.