Influence of SiO2 Nanoparticles Extracted from Biomass on the Properties of Electrodeposited Ni Matrix Composite Films on Si(100) Substrate.

Lab-made biosilica (SiO2) nanoparticles were obtained from waste biomass (rice husks) and used as eco-friendly fillers in the production of nickel matrix composite films via the co-electrodeposition technique. The produced biosilica nanoparticles were characterized using XRD, FTIR, and FE-SEM/EDS. Amorphous nano-sized biosilica particles with a high SiO2 content were obtained. Various current regimes of electrodeposition, such as direct current (DC), pulsating current (PC), and reversing current (RC) regimes, were applied for the fabrication of Ni and Ni/SiO2 films from a sulfamate electrolyte. Ni films electrodeposited with or without 1.0 wt.% biosilica nanoparticles in the electrolyte were characterized using FE-SEM/EDS (morphology/elemental analyses, roundness), AFM (roughness), Vickers microindentation (microhardness), and sheet resistance. Due to the incorporation of SiO2 nanoparticles, the Ni/SiO2 films were coarser than those obtained from the pure sulfamate electrolyte. The addition of SiO2 to the sulfamate electrolyte also caused an increase in the roughness and electrical conductivity of the Ni films. The surface roughness values of the Ni/SiO2 films were approximately 44.0%, 48.8%, and 68.3% larger than those obtained for the pure Ni films produced using the DC, PC, and RC regimes, respectively. The microhardness of the Ni and Ni/SiO2 films was assessed using the Chen-Gao (C-G) composite hardness model, and it was shown that the obtained Ni/SiO2 films had a higher hardness than the pure Ni films. Depending on the applied electrodeposition regime, the hardness of the Ni films increased from 29.1% for the Ni/SiO2 films obtained using the PC regime to 95.5% for those obtained using the RC regime, reaching the maximal value of 6.880 GPa for the Ni/SiO2 films produced using the RC regime.

Unsaturated polyester resin based composites: A case study of lignin valorisation.

Materials from green resources boast a low carbon footprint, forming the foundation of the circular economy approach in materials science. Thus, in this study, waste poly(ethylene terephthalate) (PET) was subjected to depolymerization using propylene glycol (PG), and subsequent polycondensation with bio-based maleic anhydride (MA) produced unsaturated polyester resin (b-UPR). Bio-derived acryloyl-modified Kraft lignin (KfL-A) served as a vinyl reactive filler in the b-UPR matrix to create b-UPR/KfL-A composites. The structural characterization of KfL-A and b-UPR involved the use of FTIR and NMR techniques. The mechanical properties of the newly fabricated composites were assessed through tensile strength, Vickers microhardness, and dynamic mechanical tests. The addition of KfL-A to the rigid b-UPR matrix enhanced material flexibility, resulting in less stiff and hard materials while preserving composite toughness. For instance, incorporating 10 wt% of KfL-A in b-UPR led to a 17% reduction in hardness, a 48% decrease in tensile strength, and a 20% reduction in toughness. Positive environmental impact was achieved by incorporation of 64 wt% of renewable and recycled raw material. Analogously prepared b-UPR/KfL composites showed structural inhomogeneity and somewhat better mechanical properties. Transmission (TEM) and scanning (SEM) electron microscopies revealed a suitable relationship between mechanical and structural properties of composites in relation to the extent of KfL-A addition. The UL94V flammability rating confirmed that flame resistance increased proportionally with the KfL-A addition. Once deposited in a landfill, these composites are expected to disintegrate more easily than PET, causing less harm to the environment and contributing to sustainability in the plastics cycle.

Synthesis, Characterization and Application of Biobased Unsaturated Polyester Resin Reinforced with Unmodified/Modified Biosilica Nanoparticles.

This paper presents sustainable technology for environmentally friendly composite production. Biobased unsaturated polyester resin (b-UPR), synthesized from waste polyethylene terephthalate (PET) glycosylate and renewable origin maleic anhydride (MAnh) and propylene glycol (PG), was reinforced with unmodified and vinyl-modified biosilica nanoparticles obtained from rice husk. The structural and morphological properties of the obtained particles, b-UPR, as well as composites, were characterized by Fourier-transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) techniques. The study of the influence of biosilica modification on the mechanical properties of composites was supported by hardness modeling. Improvement of the tensile strength of the b-UPR-based composite at 2.5 wt.% addition of biosilica modified with vinyl silane, named "b-UPR/SiO2-V" composite, has been achieved with 88% increase. The thermal aging process applied to the b-UPR/SiO2-V composite, which simulates use over the product's lifetime, leads to the deterioration of composites that were used as fillers in commercial unsaturated polyester resin (c-UPR). The grinded artificially aged b-UPR composites were used as filler in c-UPR for the production of a table top layer with outstanding mechanical properties, i.e., impact resistance and microhardness, as well as fire resistance rated in the V-0 category according to the UL-94 test. Developing sustainable composites that are chemically synthesized from renewable sources is important from the aspect of preserving the environment and existing resources as well as the extending their life cycle.