Dual drug nanocrystals loaded microparticles for fixed dose combination of simvastatin and ezetimibe.

Dual drug nanocrystals loaded nano embedded microparticles (DNEMs) were prepared for fixed dose combination of simvastatin (SIM) and ezetimibe (EZE) using NanoCrySP technology. The purpose was to generate nanonized SIM and EZE dispersed in matrix of single crystallization inducing excipient and investigate their in vitro performance. DNEM were prepared using mannitol (MAN) as crystallization inducer (active pharmaceutical ingredients (APIs)/MAN = 3:7 w/w) using spray drying. TPGS (0.1% w/v) was used as surfactant for stabilization of nanocrystals. Crystallinity of DNEM was confirmed by solid-state characterization using DSC and PXRD. Particle size analysis was carried out using Zetasizer® and the Scherrer equation as primary techniques and SEM and TEM as orthogonal techniques. Size of both SIM and EZE in DNEM was close to 600 nm. In vitro performance was assessed using USP apparatus II in 0.025% SLS containing sodium phosphate buffer. Powder dissolution of DNEM increased 1.45 times for SIM and 1.65 times for EZE as compared to their physical mixture in discriminatory medium. MAN did not plasticize SIM or EZE by virtue of its immiscibility with the two drugs. However, MAN helped in inducing crystallization via heterogeneous nucleation. The generated DNEM were stable in terms of assay, polymorphic form and dissolution for 90 days of accelerated storage at 40 °C/75% RH.

Bottom-up production of injectable itraconazole suspensions using membrane technology.

Bottom-up production of active pharmaceutical ingredient (API) crystal suspensions offers advantages in surface property control and operational ease over top-down methods. However, downstream separation and concentration pose challenges. This proof-of-concept study explores membrane diafiltration as a comprehensive solution for downstream processing of API crystal suspensions produced via anti-solvent crystallization. It involves switching the residual solvent (N-methyl-2-pyrrolidone, NMP) with water, adjusting the excipient (d-α-Tocopherol polyethylene glycol 1000 succinate, TPGS) quantity, and enhancing API loading (solid concentration) in itraconazole crystal suspensions. NMP concentration was decreased from 9 wt% to below 0.05 wt% (in compliance with European Medicine Agency guidelines), while the TPGS concentration was decreased from 0.475 wt% to 0.07 wt%. This reduced the TPGS-to-itraconazole ratio from 1:2 to less than 1:50 and raised the itraconazole loading from 1 wt% to 35.6 wt%. Importantly, these changes did not adversely affect the itraconazole crystal stability in suspension. This study presents membrane diafiltration as a one-step solution to address downstream challenges in bottom-up API crystal suspension production. These findings contribute to optimizing pharmaceutical manufacturing processes and hold promise for advancing the development of long-acting API crystal suspensions via bottom-up production techniques at a commercial scale.

Continuous Microfluidic Antisolvent Crystallization as a Bottom-Up Solution for the Development of Long-Acting Injectable Formulations.

A bottom-up approach was investigated to produce long-acting injectable (LAI) suspension-based formulations to overcome specific limitations of top-down manufacturing methods by tailoring drug characteristics while making the methods more sustainable and cost-efficient. A Secoya microfluidic crystallization technology-based continuous liquid antisolvent crystallization (SCT-CLASC) process was optimized and afterward compared to an earlier developed microchannel reactor-based continuous liquid antisolvent crystallization (MCR-CLASC) setup, using itraconazole (ITZ) as the model drug. After operating parameter optimization and downstream processing (i.e., concentrating the suspensions), stable microsuspensions were generated with a final solid loading of 300 mg ITZ/g suspension. The optimized post-precipitation feed suspension consisted of 40 mg ITZ/g suspension with a drug-to-excipient ratio of 53:1. Compared to the MCR-CLASC setup, where the post-precipitation feed suspensions contained 10 mg ITZ/g suspension and had a drug-to-excipient ratio of 2:1, a higher drug concentration and lower excipient use were successfully achieved to produce LAI microsuspensions using the SCT-CLASC setup. To ensure stability during drug crystallization and storage, the suspensions' quality was monitored for particle size distribution (PSD), solid-state form, and particle morphology. The PSD of the ITZ crystals in suspension was maintained within the target range of 1-10 µm, while the crystals displayed an elongated plate-shaped morphology and the solid state was confirmed to be form I, which is the most thermodynamically stable form of ITZ. In conclusion, this work lays the foundation for the SCT-CLASC process as an energy-efficient, robust, and reproducible bottom-up approach for the manufacture of LAI microsuspensions using ITZ at an industrial scale.

Development of long-acting injectable suspensions by continuous antisolvent crystallization: An integrated bottom-up process.

Our present work elucidated the operational feasibility of direct generation and stabilization of long-acting injectable (LAI) suspensions of a practically insoluble drug, itraconazole (ITZ), by combining continuous liquid antisolvent crystallization with downstream processing (i.e., centrifugal filtration and reconstitution). A novel microchannel reactor-based bottom-up crystallization setup was assembled and optimized for the continuous production of micro-suspension. Based upon the solvent screening and solubility study, N-methyl pyrrolidone (NMP) was selected as the optimal solvent and an impinging jet Y-shaped microchannel reactor (MCR) was selected as the fluidic device to provide a reproducible homogenous mixing environment. Operating parameters such as solvent to antisolvent ratio (S/AS), total jet liquid flow rates (TFRs), ITZ feed solution concentration and the maturation time in spiral tubing were tailored to 1:9 v/v, 50 mL/min, 10 g/100 g solution, and 96 h, respectively. Vitamin E TPGS (0.5% w/w) was found to be the most suitable excipient to stabilize ITZ particles amongst 14 commonly used stabilizers screened. The effect of scaling up from 25 mL to 15 L was evaluated effectively with in situ monitoring of particle size distribution (PSD) and solid-state form. Thereafter, the suspension was subjected to centrifugal filtration to remove excess solvent and increase ITZ solid fraction. As an alternative, an even more concentrated wet pellet was reconstituted with an aqueous solution of 0.5% w/w Vitamin E TPGS as resuspending agent. The ITZ LAI suspension (of 300 mg/mL solid concentration) has the optimal PSD with a D10 of 1.1 ± 0.3 µm, a D50 of 3.53 ± 0.4 µm and a D90 of 6.5 ± 0.8 µm, corroborated by scanning electron microscopy (SEM), as remained stable after 548 days of storage at 25 °C. Finally, in vitro release methods using Dialyzer, dialysis membrane sac were investigated for evaluation of dissolution of ITZ LAI suspensions. The framework presented in this manuscript provides a useful guidance for development of LAI suspensions by an integrated bottom-up approach using ITZ as model API.