Optimization of a fast deuterium diagnostic method based on visible energetic 3He spectroscopy for high electron density plasmas.

Fast ions play a crucial role in plasma heating, and their behavior in the plasma must be accurately understood. A diagnostics method based on charge exchange emission from the n = 4 - 3 transition (λ0 = 468.6 nm) of energetic 3He produced by the deuteron-deuteron reaction has been proposed as a for fast deuterons with energies in the order of MeV. The proposed method has the following advantages: No beam emission interferes with the spectra, the direction of the measuring line of sight, and the injection angle of the diagnostic beam can be freely determined. In previous studies, due to competing bremsstrahlung, it was expected that the proposed method will not be practical in the case of high electron density operation. This paper makes the proposed method available for measurement even at high electron densities by optimizing the measurement line of sight direction and the diagnostic beam incidence angle. This allows an electron density five times larger than the range of applications shown in previous studies. This result will contribute to measure of DT alpha in ITER.

Fast deuteron diagnostics using visible light spectra of 3He produced by deuteron-deuteron reaction in deuterium plasmas.

The fast deuteron (non-Maxwellian component) diagnostic method, which is based on the higher resolution optical spectroscopic measurement, has been developed as a powerful tool. Owing to a decrease in the D-H charge-exchange cross section, the diagnostic ability of conventional optical diagnostic methods should be improved for ∼MeV energy deuterons. Because the 3He-H charge-exchange cross section is much larger than that of D-H in the ∼MeV energy range, the visible light (VIS) spectrum of 3He produced by the dueteron-dueteron (DD) reaction may be a useful tool. Although the density of 3He is small because it is produced via the DD reaction, improvement of the emissivity of the VIS spectrum of 3He can be expected by using a high-energy beam. We evaluate the VIS spectrum of 3He for the cases when a fast deuteron tail is formed and not formed in the ITER-like beam injected deuterium plasma. Even when the beam energy is in the MeV energy range, a large change appears in the half width at half maximum of the VIS spectrum. The emissivity of the VIS spectrum of 3He and the emissivity of bremsstrahlung are compared, and the measurable VIS spectrum is obtained. It is shown that the VIS spectrum of 3He is a useful tool for the MeV beam deuteron tail diagnostics.

Conceptual design of a collimator for the neutron emission profile monitor in JT-60SA using Monte Carlo simulations.

Materials and structures of a collimator for a new neutron emission profile monitor in JT-60SA are examined through Monte Carlo simulations using the Monte Carlo N-Particle transport code. First, the shielding properties of various material combinations are compared in order to determine a combination with high shielding performances against both neutrons and gamma-rays. It is found that a collimator consisting of borated polyethylene and lead has a high shielding performance against neutrons. Moreover, a high shielding performance against gamma-rays is obtained when a lead pipe with a radial thickness of 0.01 m is inserted into a collimation tube. Second, we demonstrate that it is possible to improve the spatial resolution to a desired level by installing a thin tubular extension structure that fits into the limited space available between the main collimator block and the tokamak device. Finally, the collimator structures that meet both the targeted spatial resolutions (<10% of the plasma minor radius) and the targeted counting rate (105 cps order) are discussed.

Design optimization of a fast-neutron detector with scintillating fibers for triton burnup experiments at fusion experimental devices.

Time-resolved triton burnup studies have been carried out to estimate the behavior of alpha particles in DD fusion experimental devices. In those studies, 14 MeV neutrons emitted through DT reactions in DD plasmas should be measured selectively in the backgrounds of DD neutrons and gamma rays. For this purpose, a scintillating-fiber (Sci-Fi) based fast-neutron detector has been adapted because of its advantages such as fast response, design flexibility in detection efficiency by changing the number of Sci-Fi, and discrimination property against 2.4 MeV neutrons produced through DD reactions and gamma rays. However, its length had conventionally been set to around 10 cm without an optimization study of its design parameters to meet the requirements as 14 MeV neutron detector. In the present study, we tested three types of Sci-Fi detectors with three different lengths and compared with the simulated results of energy deposition, through which we tried to understand the phenomena in the detection process of fast neutrons. From the results, it has been shown that, due to the self-shielding of neutrons by Sci-Fi and the attenuation of scintillation photons during the transmission process to the photomultiplier tube, the optimal length of Sci-Fi is concluded to be about 6 cm.

The large helical device vertical neutron camera operating in the MHz counting rate range.

In the currently performed neutral beam (NB) -heated deuterium plasma experiments, neutrons are mainly produced by a beam-plasma reaction. Therefore, time-resolved measurement of the neutron emission profile can enhance the understanding of the classical and/or anomalous transport of beam ions. To measure radial neutron emission profiles as a function of time, the vertical neutron camera (VNC) capable of operation with a counting rate in the MHz range was newly installed on the Large Helical Device (LHD). This is the world's first neutron camera for stellarator/heliotron devices. The VNC consists of a multichannel collimator, eleven fast-neutron detectors, and the digital-signal-processing-based data acquisition system (DAQ). The multichannel collimator having little cross talk was made from hematite-doped heavy concrete, which has a high shielding performance against both neutrons and gamma-rays. A stilbene crystal coupled with a photomultiplier having high-gain-stability in the high-count rate regime was utilized as a fast-neutron scintillation detector because it has a high neutron-gamma discrimination capability at high count rates. The DAQ system equipped with a field programmable logic controller was developed to obtain the waveform acquired with a 1 GHz sampling rate and the shaping parameter of each pulse simultaneously at up to 106 cps (counts per second). Neutron emission profiles were successfully obtained in the first deuterium campaign of LHD in 2017. The neutron emission profile was measured in tangentially co-injected NB-heated plasma with different magnetic axes (R ax). The neutron counts became larger in the inward-shifted configuration, which was consistent with the total neutron rate measured by the neutron flux monitor. The radial peak position of the line-integrated neutron profile which changed according to R ax showed that the VNC worked successfully as designed. The VNC demonstrated the expected performance conducive to extending energetic-particle physics studies in LHD.

Initial operation results of NE213 scintillation detector for time-resolved measurements on triton burnup in KSTAR.

In time-resolved measurement for triton burnup in Korea Superconducting Tokamak Advanced Research (KSTAR) deuterium plasmas, an NE213 liquid scintillation detector was installed and operated during the 2017 KSTAR campaign. The detector is composed of an NE213 scintillator (50 mm in diameter and 10 mm in thickness) and a photomultiplier tube (PMT). The PMT anode signal was processed under a data acquisition system which contains a field programmable gate array circuit and pulse processing software that is capable of discriminating gamma-ray and neutron pulse signals. In order to determine an appropriate threshold level for the 14 MeV neutron signal resulting from triton burnup, the NE213 scintillation detector was calibrated by using d-d and d-t neutron generators at the National Fusion Research Institute and Intense 14 MeV Neutron Source Facility, OKTAVIAN, Osaka University, Japan. The detector was installed on KSTAR with a 10 mm thick soft-iron stray magnetic field shield and a radiation shield which consists of 100 mm thick lead blocks and 200 mm thick borated polyethylene blocks. A discrimination range for d-t neutron was determined based on test results from neutron generators and KSTAR. Data points selected from the discrimination range were consistent with the classical triton confinement characteristics. In conclusion, under condition of an input counting rate of 1.9 × 105 counts per second (CPS), the detector is able to measure triton burnup signals up to 500 CPS for various plasma parameters.

Dose-response to a jelly preparation of calcium polystyrene sulfonate in patients with hyperkalemia--changes in serum potassium levels with or without a RAAS inhibitor.

AIMS: In this study, dose-response of the serum potassium-lowering effect of a calcium polystyrene sulfonate (PS) preparation was investigated. Changes in the serum potassium level were also examined with or without application of a RAAS inhibitor, which is said to increase the serum potassium level. SUBJECTS AND METHODS: 23 patients diagnosed to have hyperkalemia associated with chronic renal failure were enrolled in this study. The study drug, a PS-Ca jelly preparation (Argamate jelly), was started at a daily dose of 1 preparation (5 g as PS-Ca), and the dose was increased by 1 preparation every month to finally reach 3 preparations per day. Blood samples were collected once a month and serum levels of creatinine and electrolytes were measured. RESULTS: PS-Ca jelly decreased serum potassium levels in a dose-dependent manner. Decreases were 0.67 mEq/l at 5 g of PS-Ca/day, 1.06 mEq/l at 10 g/d, and 1.33 mEq/l at 15 g/d. Irrespective of the use of the RAAS inhibitor, serum potassium levels decreased significantly in a dose-dependent manner. Furthermore, no major change in serum creatinine levels occurred in subjects in which the RAAS inhibitor was used, although in subjects in which the RAAS inhibitor was not used, serum creatinine level tended to gradually increase. CONCLUSION: Serum potassium levels were reduced in a dose-dependent manner by administration of 5-15 g/d of PS-Ca, and it appeared that together with control of serum potassium levels, renal function should be maintained by continuous administration of RAAS inhibitor.

Fast response neutron emission monitor for fusion reactor using stilbene scintillator and Flash-ADC.

The stilbene neutron detector which has been used for neutron emission profile monitoring in JT-60U has been improved, to respond to the requirement to observe the high-frequency phenomena in megahertz region such as toroidicity-induced Alfvén Eigen mode in burning plasma as well as the spatial profile and the energy spectrum. This high-frequency phenomenon is of great interest and one of the key issues in plasma physics in recent years. To achieve a fast response in the stilbene detector, a Flash-ADC is applied and the wave form of the anode signal stored directly, and neutron/gamma discrimination was carried out via software with a new scheme for data acquisition mode to extend the count rate limit to MHz region from 1.3 x 10(5) neutron/s in the past, and confirmed the adequacy of the method.

In situ calibration of neutron activation system on the large helical device.

In situ calibration of the neutron activation system on the Large Helical Device (LHD) was performed by using an intense 252Cf neutron source. To simulate a ring-shaped neutron source, we installed a railway inside the LHD vacuum vessel and made a train loaded with the 252Cf source run along a typical magnetic axis position. Three activation capsules loaded with thirty pieces of indium foils stacked with total mass of approximately 18 g were prepared. Each capsule was irradiated over 15 h while the train was circulating. The activation response coefficient (9.4 ± 1.2) × 10-8 of 115In(n, n')115mIn reaction obtained from the experiment is in good agreement with results from three-dimensional neutron transport calculations using the Monte Carlo neutron transport simulation code 6. The activation response coefficients of 2.45 MeV birth neutron and secondary 14.1 MeV neutron from deuterium plasma were evaluated from the activation response coefficient obtained in this calibration experiment with results from three-dimensional neutron calculations using the Monte Carlo neutron transport simulation code 6.

Development of fast neutron pinhole camera using nuclear emulsion for neutron emission profile measurement in KSTAR.

We have developed a compact fast neutron camera based on a stack of nuclear emulsion plates and a pinhole collimator. The camera was installed at J-port of Korea superconducting tokamak advanced research at National Fusion Research Institute, Republic of Korea. Fast neutron images agreed better with calculated ones based on Monte Carlo neutron simulation using the uniform distribution of Deuterium-Deuterium (DD) neutron source in a torus of 40 cm radius.

All-optical digital-to-analog conversion using pulse pattern recognition based on optical correlation processing.

We propose and demonstrate a novel all-optical digital-to-analog (D/A) conversion using pulse pattern recognition based on optical correlation processing. It is composed of pulse pattern recognition based on correlation processing and intensity adjustment using an optical attenuator. We obtain a single pulse as a result of pulse pattern recognition by using correlation processing between a target digital signal and a prepared correlation filter function. The obtained single pulse can be promptly fed to an output port as a corresponding analog signal through adequate intensity adjustment. Experimental results show that four-bit digital signals with 1.65ps interval can be successfully converted to analog signals corresponding to input digital signals.

Shielding design of the ITER NBI duct for nuclear and bremsstrahlung radiation.

Three-dimensional Monte Carlo shielding analyses are conducted on the ITER Neutral Beam Injection (NBI) duct for the nuclear and bremsstrahlung radiation. The detailed distribution is evaluated about the nuclear heating rate and surface heat load of the NBI duct wall by the neutron and photon transport calculation. The analytical representations of these nuclear responses are established as a function of the distance from the blanket surface. It is clarified that these representations are different between the duct wall facing the plasma and that hidden from the plasma, and also between the duct wall in the blanket region and that in the vacuum vessel region. These results are very useful for the shielding design of the NBI duct wall in the nuclear fusion reactor.

Experiment and analyses for 14 MeV neutron streaming through a dogleg duct.

There are several vacant channels for diagnosis, RF heating and so on through the shielding structure in fusion reactors. Some of them consist of dogleg ducts, through which neutrons stream in a complex manner. An experiment was conducted with the Fusion Neutronics Source (FNS) facility at JAERI to study the behaviour of neutrons in the duct and assess the reliability of calculation methods for the design of fusion reactors such as ITER. The assembly was an iron slab 180 cm in thickness with a doubly bent duct 30 x 30 cm2 in cross section. The experiment was analysed using a simple design code for radiation streaming, DUCT-III, and the Monte Carlo code MCNP. The results indicate that the simple design code is reliable enough to be used for shielding design analyses as well as the Monte Carlo method, which showed excellent agreement between calculated and measured values.

The method of urinary total kallikrein and prekallikrein measurement, and their urinary excretions in the patients with essential hypertension.

The method of measurement for urinary total kallikrein (KAL) and preKAL in human was developed, and daily excretions of urinary total KAL, KAL and preKAL were investigated in patients with essential hypertension. Forty microliter of urine samples were incubated with or without 120 micrograms of chymotrypsin-free trypsin for total KAL or KAL, respectively. KAL was measured with direct radioimmunoassay and kininogenase assay. PreKAL was calculated by the subtraction of KAL from total KAL. The subjects of this study included 7 normotensives (NT) and 8 essential hypertensives (EHT). Daily excretions of total KAL, KAL and preKAL were significantly lower in EHT than those in NT. KAL/total KAL ratio, which reflects the conversion rate from preKAL to KAL in the kidney, was not significantly different between EHT and NT. From these results, it is suggested that decreased urinary KAL excretion in EHT is mainly caused by reduced preKAL production rather than the impaired conversion from preKAL to KAL in the kidney. It is emphasized that this method of measurement for urinary total KAL and preKAL may be a very useful tool for research of the renal kallikrein-kinin system.

Purification of human low molecular weight kininogen and its application for a simple ND sensitive method for determination of human urinary kallikrein activity.

Human plasma low molecular weight kininogen was purified with ammonium sulfate fractionation, DEAE-cellulose, CM-Sephadex C-50 and aprotinin-agarose affinity column chromatography, after which this was further purified with Sephadex G-150 and DEAE-Sephadex A-50 column chromatographies. Kallikrein activity was measured as the kininogenase activity reflecting the kinin-producing capacity from kininogen. The purification factor from crude plasma to purified substrate was 44-fold, and the recovery was 18%. The purified human substrate did not contain kinin-generating or destroying enzymes which would interfere with kininogenase activity, and showed a cross-reactivity of less than 0.1% against kinin antiserum. In the kininogenase assay, all kininogen was removed by adding ethanol to terminate the enzyme reaction. Because of the high sensitivity of kinin radioimmunoassay, the kinin levels in urine could be determined in very small amounts of samples (0.5 to 2.0 nl of the original urine). These findings indicated that kinin levels in incubation solution could be measured directly, and the control tubes are unnecessary in this assay procedure. In a comparison among human, dog and bovine low molecular weight kininogen as the substrate for human urinary kallikrein, the enzyme activity was 5 and 80 fold higher in the human low molecular weight kininogen, respectively, suggesting that a human substrate is the best for human enzymes. This simple, specific, sensitive and homologous kininogenase assay system seems to be very useful investigating the physiological or pathophysiological role of the renal kallikrein-kinin system in hypertensive and renal diseases.

Interrelation between the renin-angiotensin system and kallikrein-kinin system in patients with essential hypertension.

In order to investigate the relationship between the kallikrein-kinin (K-K) system and renin-angiotensin (R-A) system, plasma kinin (pKIN), plasma angiotensin II (pAII), plasma renin activity (PRA) and angiotensin converting enzyme activity (ACEA) were determined in 19 essential hypertensives (EHT). pKIN and pATII measurements were performed by highly sensitive radioimmunoassay (RIA), both of which were established in our laboratory. The assay sensitivity of pKIN and pAII were 0.5 pg/tube and 0.1 pg/tube, respectively. In pKIN RIA, pKIN was extracted by ethanol from 0.8 ml of plasma obtained with a syringe containing kinin generating and destroying enzyme inhibitors. In pAII RIA, pAII was measured directly in small amounts of 50-100 microliter, unextracted plasma samples. The level in pAII was significantly higher (p less than 0.05) in the normal renin group (NRH: n = 13) as compared with low renin group of EHT (LRH: n = 6). However, no significant difference was found in pKIN and ACEA between these two groups. Although a significantly positive correlation was observed between pAII and PRA (p less than 0.001) in EHT, the ratio of pAII/PRA tended to be higher in LHR than in NRH. ACEA correlated positively with pAII (p less than 0.01) or PRA (p less than 0.02), respectively. On the other hand, a significant negative correlation was also found between pKIN and pAII (p less than 0.05). From these findings, it was assumed that there was a closed relationship between R-A and K-K systems, and that angiotensin converting enzyme (kininase II) might play some role in the interrelation between both systems.

Comprehensive studies on the renal kallikrein-kinin system in essential hypertension.

In order to investigate the role of the renal kallikrein-kinin (K-K) system in normal (NRH) and low renin (LRH) subgroups of essential hypertension (EHT), daily urinary excretions of renal K-K system components including kallikrein (KAL), total KAL, pre-KAL, kinin (KIN) and kininase (total, I and II), were measured in 21 normotensives (NT) and 45 patients with EHT (NRH: 29, LRH: 16). Urinary KAL and KIN quantities, KAL activity, total and pre-KAL, and kininase (total, I and II) were measured by direct RIA, kininogenase assay, direct RIA of KAL after trypsin treatment, and KIN destroying capacity, respectively. The daily excretions of KAL quantity and activity, total and pre-KAL, and KIN were significantly lower in EHT than in NT. That of total kininase and kininase I were significantly higher in EHT than in NT while no significant difference was found in kininase I between EHT and NT. In comparing NRH and LRH, the urinary KAL activity and KIN were lower in LRH than in NRH, and kininase I was higher in LRH than in NRH. No significant difference, however, was found in total and pre-KAL, KAL quantity and kininase II between NRH and LRH. The ratio of KAL quantity/total KAL which reflects the conversion rate from pre-KAL in the kidney, did not show any significant difference among NT, NRH and LRH.(ABSTRACT TRUNCATED AT 250 WORDS)

Wide dynamic range neutron flux monitor having fast time response for the Large Helical Device.

A fast time response, wide dynamic range neutron flux monitor has been developed toward the LHD deuterium operation by using leading-edge signal processing technologies providing maximum counting rate up to ∼5 × 10(9) counts/s. Because a maximum total neutron emission rate over 1 × 10(16) n/s is predicted in neutral beam-heated LHD plasmas, fast response and wide dynamic range capabilities of the system are essential. Preliminary tests have demonstrated successful performance as a wide dynamic range monitor along the design.

Development of in-vessel components of the microfission chamber for ITER.

Microfission chambers (MFCs) will measure the total neutron source strength in ITER. The MFCs will be installed behind blanket modules in the vacuum vessel (VV). Triaxial mineral insulated (MI) cables will carry signals from the MFCs. The joint connecting triaxial MI cables in the VV must be considered because the MFCs and the MI cables will be installed separately at different times. Vacuum tight triaxial connector of the MI cable has been designed and a prototype has been constructed. Performance tests indicate that the connector can be applied to the ITER environment. A small bending-radius test of the MI cable indicates no observed damage at a curvature radius of 100 mm.