Optimization and Formulation of Fucoxanthin-Loaded Microsphere (F-LM) Using Response Surface Methodology (RSM) and Analysis of Its Fucoxanthin Release Profile.

Fucoxanthin has interesting anticancer activity, but is insoluble in water, hindering its use as a drug. Microencapsulation is used as a technique for improving drug delivery. This study aimed to formulate fucoxanthin-loaded microspheres (F-LM) for anticancer treatment of H1299 cancer cell lines and optimize particle size (PS) and encapsulation efficiency (EE). Using response surface methodology (RSM), a face centered central composite design (FCCCD) was designed with three factors: Polyvinylalcohol (PVA), poly(d,l-lactic-co-glycolic acid) (PLGA), and fucoxanthin concentration. F-LM was produced using a modified double-emulsion solvent evaporation method. The F-LM were characterized for release profile, release kinetics, and degradation pattern. Optimal F-LM PS and EE of 9.18 µm and 33.09%, respectively, with good surface morphology, were achieved from a 0.5% (w/v) PVA, 6.0% (w/v) PLGA, 200 µg/mL fucoxanthin formulation at a homogenization speed of 20,500 rpm. PVA concentration was the most significant factor (p < 0.05) affecting PS. Meanwhile, EE was significantly affected by interaction between the three factors: PVA, PLGA, and fucoxanthin. In vitro release curve showed fucoxanthin had a high burst release (38.3%) at the first hour, followed by a sustained release stage reaching (79.1%) within 2 months. Release kinetics followed a diffusion pattern predominantly controlled by the Higuchi model. Biodegradability studies based on surface morphology changes on the surface of the F-LM, show that morphology changed within the first hour, and F-LM completely degraded within 2 months. RSM under FCCCD design improved the difference between the lowest and highest responses, with good correlation between observed and predicted values for PS and EE of F-LM.

Fabrication of Fucoxanthin-Loaded Microsphere(F-LM) By Two Steps Double-Emulsion Solvent Evaporation Method and Characterization of Fucoxanthin before and after Microencapsulation.

Microencapsulation is a promising approach in drug delivery to protect the drug from degradation and allow controlled release of the drug in the body. Fucoxanthin-loaded microsphere (F-LM) was fabricated by two step w/o/w double emulsion solvent evaporation method with poly (L-lactic-coglycolic acid) (PLGA) as carrier. The effect of four types of surfactants (PVA, Tween-20, Span-20 and SDS), homogenization speed, and concentration of PLGA polymer and surfactant (PVA), respectively, on particle size and morphology of F-LM were investigated. Among the surfactants tested, PVA showed the best results with smallest particle size (9.18 µm) and a smooth spherical surface. Increasing the homogenization speed resulted in a smaller mean F-LM particle size [d(0.50)] from 17.12 to 9.18 µm. Best particle size results and good morphology were attained at homogenization speed of 20 500 rpm. Meanwhile, increased PLGA concentration from 1.5 to 11.0 (% w/v) resulted in increased F-LM particle size. The mean particle size [d(0.5)] of F-LM increased from 3.93 to 11.88 µm. At 6.0 (% w/v) PLGA, F-LM showed the best structure and external morphology. Finally, increasing PVA concentration from 0.5 to 3.5 (% w/v) resulted in decreased particle size from 9.18 to 4.86 µm. Fucoxanthin characterization before and after microencapsulation was carried out to assess the success of the microencapsulation procedure. Thermo gravimetry analysis (TGA), glass transition (Tg) temperature of F-LM and fucoxanthin measured using DSC, ATR-FTIR and XRD indicated that fucoxanthin was successfully encapsulated into the PLGA matrix, while maintaining the structural and chemical integrity of fucoxanthin.