Cleansing efficacy of an auto-cleaning toothbrushing device with nylon bristles: a randomized-controlled pilot study.

OBJECTIVES: To compare the cleansing efficacy of an auto-cleaning device with nylon bristles (Y-brush®) to that of manual toothbrushing. MATERIALS AND METHODS: Twenty probands refrained from oral hygiene for 3 days. Rustogi Modified Navy Plaque Index was assessed before and after (randomized) toothbrushing either with the auto-cleaning device for 5 s per jaw or with a manual toothbrush for a freely chosen time up to 4 min. The clinical investigation was repeated in a cross-over design. In a third trial period, the brushing time for auto-cleaning was increased to 15 s per jaw. The study was supplemented by plaster cast analyses. RESULTS: Full-mouth plaque reduction was higher with manual toothbrushing than with auto-cleaning for 5 s per jaw (p < 0.001). There was no statistically significant difference on smooth tooth surfaces but on marginal and interdental sites. Increasing the brushing time of auto-cleaning to 15 s per jaw resulted in a comparable full-mouth plaque reduction as with manual toothbrushing (p = 0.177). In 95% of individuals, the device was too short not completely covering second molars. In 30.67% of teeth, the gingival margin was not covered by bristles. CONCLUSIONS: Auto-cleaning devices with nylon bristles have a future potential to reach plaque reduction levels comparable to manual toothbrushing, although manufacturers must focus on improving an accurate fit. CLINICAL RELEVANCE: Under the premise of an ameliorated fit, the auto-cleaning device might be recommendable for people with low brushing efficacy. Interdental sites remain a failure point if adjunct interdental cleaning is not viable.

Cleansing efficacy of an oral irrigator with microburst technology in orthodontic patients-a randomized-controlled crossover study.

OBJECTIVES: Orthodontic patients struggle with interdental cleaning calling for simpler mechanical devices to reduce the high plaque levels. The present study aimed to compare the cleansing efficacy of an oral irrigator with that of dental flossing in patients with fixed braces after 4 weeks of home-use. MATERIALS AND METHODS: The study design is a randomized and single-blinded cross-over study. After 28 days using the products at home, hygiene indices (Rustogi Modified Navy Plaque Index (RMNPI); gingival bleeding index (GBI)) were compared between test (oral irrigator) and control product (dental floss). RESULTS: Seventeen adult individuals finalized the study. After 28 days of cleaning with the oral irrigator, RMNPI was 54.96% (46.91-66.05) compared to 52.98% (42.75-65.60) with dental floss (p = 0.029). Subgroup analysis revealed that the higher cleansing efficacy of the dental floss is attributable to buccal and marginal areas. GBI after the test phase with the oral irrigator was 12.96% (7.14-24.31) and statistically significantly higher compared to 8.33% (5.84-15.33) with dental floss (p = 0.030) which could be seen in all subgroups. CONCLUSIONS: Oral irrigators do not remove plaque and reduce gingival bleeding as efficiently as dental floss in easily accessible regions. However, in posterior regions, where the patients struggled with the application of dental floss, the oral irrigator showed similar results. CLINICAL RELEVANCE: Oral irrigators should only be recommended to orthodontic patients who cannot use interdental brushes and are not compliant with dental flossing.

Comparison of allogeneic and autogenous bone grafts for augmentation of alveolar ridge defects-A 12-month retrospective radiographic evaluation.

OBJECTIVES: The aim of this study was to compare three-dimensional alterations following the use of autogenous versus allogeneic onlay grafts for augmentation at single tooth defects. MATERIALS AND METHODS: Alveolar bone width at specific implant sites were assessed using sagittal and cross-sectional CBCT images prior grafting and at three subsequent time points. Twenty-one patients received autogenous bone blocks harvested from the retromolar region and another 21 patients received freeze-dried cancellous allogeneic bone blocks. RESULTS: The vertical and horizontal dimensions did not significantly differ between autogenous and allogeneic bone grafts at any time point. In addition, there were no statistically significant differences in graft remodeling rates between autogenous (mean shrinkage rate after 12 months: 12.5% ± 7.8%) and allogeneic onlay grafts (mean shrinkage rate after 12 months: 14.4% ± 9.8%). CONCLUSIONS: Freeze-dried cancellous allogeneic bone blocks showed equivalent volumetric shrinkage rates as autogenous bone blocks when used for treating circumscribed bone defects classified as Type-II to Type-IV according to the ITI-treatment guide categories. Therefore, it is not necessary to over-contour the alveolar ridge when using allogeneic blocks for treating single tooth defects, but to apply the same procedure as when using autogenous blocks.

Human papillomavirus prevalence in a Mid-European oral squamous cell cancer population: A cohort study.

OBJECTIVES: Human papillomavirus infection has been investigated intensively regarding oropharyngeal carcinoma. However, there is still lack of knowledge about the impact of oral HPV infections concerning oral squamous cell carcinoma. This study investigates the prevalence of oral HPV infection in such patients, identifying possible differences between HPV+ and HPV- patients. SUBJECTS AND METHODS: One hundred and six consequent patients were investigated. After completion of a study questionnaire regarding risk factors, a brush smear sample was taken in each subject to identify the individual oral HPV status (overall/low risk/high risk). RESULTS: About 35.8% of the patients were tested positive for HPV in the oral cavity (14% low risk, 28.3% high risk). Patients with oral HPV infection and high-risk HPV infection were significantly younger (p < 0.001) and had a higher alcohol consumption (p = 0.0075 resp. p = 0.0022). A high number of different sexual partners were significantly correlated with any type of HPV infection. At last, patients with high-risk oral HPV infection had experienced more tooth extractions during their lifetime. CONCLUSION: Oral HPV infections may influence the course of disease of oral squamous cell carcinoma as HPV+ patients are about 10 years younger. It seems that high alcohol consumption facilitates high-risk HPV infection. It may be presumed that both alcohol consumption and high-risk oral HPV infection act synergistically, explaining earlier cancer onset.

Is Virtual Surgical Planning in Orthognathic Surgery Faster Than Conventional Planning? A Time and Workflow Analysis of an Office-Based Workflow for Single- and Double-Jaw Surgery.

PURPOSE: The purpose of this study was to measure and compare the working time for virtual surgical planning (VSP) in orthognathic surgery in a largely office-based workflow in comparison with conventional surgical planning (CSP) regarding the type of surgery, staff involved, and working location. MATERIALS AND METHODS: This prospective cohort study included patients treated with orthognathic surgery from May to December 2016. For each patient, both CSP with manual splint fabrication and VSP with fabrication of computer-aided design-computer-aided manufacturing splints were performed. The predictor variables were planning method (CSP or VSP) and type of surgery (single or double jaw), and the outcome was time. Descriptive and analytic statistics, including analysis of variance for repeated measures, were computed. RESULTS: The sample was composed of 40 patients (25 female and 15 male patients; mean age, 24.6 years) treated with single-jaw surgery (n = 18) or double-jaw surgery (n = 22). The mean times for planning single-jaw surgery were 145.5 ± 11.5 minutes for CSP and 109.3 ± 10.8 minutes for VSP, and those for planning double-jaw surgery were 224.1 ± 11.2 minutes and 149.6 ± 15.3 minutes, respectively. Besides the expected result that the working time was shorter for single-versus double-jaw surgery (P < .001), it was shown that VSP shortened the working time significantly versus CSP (P < .001). The reduction of time through VSP was relatively stronger for double-jaw surgery (P < .001 for interaction). All differences between CSP and VSP regarding profession (except for the surgeon's time investment) and location were statistically significant (P < .01). The surgeon's time to plan single-jaw surgery was 37.0 minutes for CSP and 41.2 minutes for VSP; for double-jaw surgery, it was 53.8 minutes and 53.6 minutes, respectively. CONCLUSIONS: Office-based VSP for orthognathic surgery was significantly faster for single- and double-jaw surgery. The time investment of the surgeon was equal for both methods, and all other steps of the workflow differed significantly compared with CSP.

Can ultra-low-dose computed tomography reliably diagnose and classify maxillofacial fractures in the clinical routine?

Purpose: Maxillofacial trauma predominantly affects young adults between 20 and 40 years of age. Although radioprotection is a legal requirement, the significant potential of dose reduction in computed tomography (CT) is still underused in the clinical routine. The objective of this study was to evaluate whether maxillofacial fractures can be reliably detected and classified using ultra-low-dose CT. Materials and Methods: CT images of 123 clinical cases with maxillofacial fractures were classified by two readers using the AOCOIAC software and compared with the corresponding results from post-treatment images. In group 1, consisting of 97 patients with isolated facial trauma, pre-treatment CT images at different dose levels (volumetric computed tomography dose index: ultra-low dose, 2.6 mGy; low dose, <10 mGy; and regular dose, <20 mGy) were compared with post-treatment cone-beam computed tomography (CBCT). In group 2, consisting of 31 patients with complex midface fractures, pre-treatment shock room CT images were compared with post-treatment CT at different dose levels or CBCT. All images were presented in random order and classified by 2 readers blinded to the clinical results. All cases with an unequal classification were re-evaluated. Results: In both groups, ultra-low-dose CT had no clinically relevant effect on fracture classification. Fourteen cases in group 2 showed minor differences in the classification code, which were no longer obvious after comparing the images directly to each other. Conclusion: Ultra-low-dose CT images allowed the correct diagnosis and classification of maxillofacial fractures. These results might lead to a substantial reconsideration of current reference dose levels.

Local Release of Strontium from Sputter-Deposited Coatings at Implants Increases the Strontium-to-Calcium Ratio in Peri-implant Bone.

It is well known that strontium (Sr) has a significant effect on peri-implant bone healing when administered systemically. Due to the risk of adverse effects of such treatments, new routes focusing on the local, sustained release of Sr from bone-implant contact surfaces have been explored, with success in in vivo experiments. However, the increase of Sr concentrations in the peri-implant bone has not been described in depth yet. Here, we show that a local, sustained Sr release from Ti-Sr-O physical vapor deposition (PVD) coatings by magnetron sputter coating increases the Sr/Ca ratio close to the implant in a rabbit model and that the Sr/Ca background level is reached approximately 500 µm from the implant.

Customized allogeneic bone grafts for maxillary horizontal augmentation: A 5-year follow-up radiographic and histologic evaluation.

We report the histological evaluation of an individualized allogeneic bone block 5 years after alveolar ridge augmentation. The biopsy showed a well-vascularized lamellar bone with fatty incorporations without any avital allograft remnants. The presence of osteocytes, lining cells, macrophages, and blood vessels indicated a healthy and vital bone tissue.

Cervical Lymph Node Metastases in Oral Squamous Cell Carcinoma-How Much Imaging Do We Need?

Cervical lymph node metastases in oral squamous cell carcinoma (OSCC) are key predictors of disease specific survival. It was therefore the aim of this study to evaluate how much imaging is minimally needed for reliable and efficient identification of cervical lymph node metastases. In this retrospective cross-sectional study, results (metastasis yes/no) of ultrasound (US), computed tomography (CT), magnetic resonance imaging (MRI), and positron emission tomography (PET) were compared to the final histopathological results of the corresponding neck dissection (ND) specimens (metastasis yes/no). A score was calculated to account for cervical lymph node size, shape, clustering, peripheral enhancement, hilus sign, architecture, blood flow, and central necrosis. Sensitivity and specificity were analyzed for each imaging technique separately. In 164 patients diagnosed with OSCC, 96 underwent uni- or bilateral ND (122 ND in total). One hundred percent sensitivity was achieved by CT+MRI, MRI+PET, US+CT+MRI, US+MRI+PET, CT+MRI+PET, and US+CT+MRI+PET. The highest specificity was realized by US with 79% (95% CI [0.698-0.890]). Specificity for CT+MRI and PET+MRI was 51% (95% CI [0.359-0.665]) and 70% (95% CI [0.416-0.984]), respectively. Regarding 100% sensitivity with acceptable specificity, the combination of CT+MRI or PET+MRI appeared to be suitable for staging cervical lymph nodes in primary OSCC.

Clinical Outcome Following Surgical Repair of Small Versus Large Orbital Floor Fractures Using Polyglactin 910/Polydioxanone (Ethisorb®).

The aim of this retrospective study was to evaluate the clinical outcome of surgical management of small versus large, isolated orbital floor fractures (OFFs) using polyglactin 910/polydioxanone (Ethisorb®). Covering a four-year period (2010-2013), all records concerning midfacial fractures with involvement of the orbit were screened. Isolated fractures of the orbital floor as well as combined injuries of the orbital floor and medial wall that had been treated surgically using polyglactin 910/polydioxanone (Ethisorb®) were included. Patients underwent a preoperative, a postoperative, and a late ophthalmologic assessment. The clinical outcomes of surgically managed small OFFs up to 2 cm2 were statistically analyzed and compared to clinical results in larger defects. The final sample included 61 patients (25 women, 36 men). Fractures up to 2 cm2 were found in 33 patients (54.1%), whereas 28 patients (45.9%) suffered from OFFs larger than 2 cm2. The clinical outcomes did not significantly differ between both sample categories, and statistical analysis showed a power of 0.91 to detect a potentially existing difference. On final examination, 52 patients were free of any clinical symptoms, whereas minor issues were found in seven subjects, and two patients suffered from severe impairment. In conclusion, polyglactin 910/polydioxanone (Ethisorb®) seems to be a suitable material for surgical repair of both small and large OFFs.

In Vitro Analysis of the Fracture Resistance of CAD/CAM Denture Base Resins.

Computer-aided design and computer-aided manufacturing (CAD/CAM) denture base manufacturers claim to produce their resin pucks under high heat and pressure. Therefore, CAD/CAM dentures are assumed to have enhanced mechanical properties and, as a result, are often produced with lower denture base thicknesses than conventional, manually fabricated dentures. The aim of this study was to investigate if commercially available CAD/CAM denture base resins have more favourable mechanical properties than conventionally processed denture base resins. For this purpose, a series of three-point bending tests conforming to ISO specifications were performed on a total of 80 standardised, rectangular CAD/CAM denture base resin specimens from five different manufacturers (AvaDent, Baltic Denture System, Vita VIONIC, Whole You Nexteeth, and Wieland Digital Dentures). A heat-polymerising resin and an autopolymerising resin served as the control groups. The breaking load, fracture toughness, and the elastic modulus were assessed. Additionally, the fracture surface roughness and texture were investigated. Only one CAD/CAM resin showed a significantly increased breaking load. Two CAD/CAM resins had a significantly higher fracture toughness than the control groups, and all CAD/CAM resins had higher elastic moduli than the controls. Our results indicate that CAD/CAM denture base resins do not generally have better mechanical properties than manually processed resins. Therefore, the lower minimum denture base thicknesses should be regarded with some caution.

A comparative in vivo study of strontium-functionalized and SLActive™ implant surfaces in early bone healing.

PURPOSE: Studies have shown that strontium-doped medical applications benefit bone metabolism leading to improved bone healing and osseointegration. Based on this knowledge, the aim of the study was to evaluate the performance of an implant surface, functionalized by a physical vapor deposition (PVD) coating (Ti-Sr-O), designed to yield predictable release of strontium. The Ti-Sr-O functionalized surface is compared to a routinely used, commercially available surface (SLActive™) with respect to bone-to-implant contact (BIC%) and new bone formation (BF%) in two defined regions of interest (ROI-I and ROI-II, respectively). MATERIALS AND METHODS: Ti-Sr-O functionalized, SLActive, and Grade 4 titanium implants were inserted in the femoral condyle of adult male New Zealand White rabbits. The PVD magnetron-sputtered Ti-Sr-O surface coating was characterized using scanning electron microscopy (SEM) for morphology and coating thickness. Strontium release and mechanical stability of the coating, under simulated insertion conditions, were evaluated. Furthermore, histomorphometrical BIC and BF were carried out 2 weeks after insertion. RESULTS: Histomorphometry revealed increased bone formation of Ti-Sr-O with significant differences compared to SLActive and Grade 4 titanium in both regions of interest, ROI-I and ROI-II, at 0-250 µm and 250-500 µm distance from the implant surfaces. Analogous results of bone-to-implant contact were observed for the two modified surfaces. CONCLUSION: The results show that a nanopatterned Ti-Sr-O functionalized titanium surface, with sustained release of strontium, increases peri-implant bone volume and could potentially contribute to enhancement of bone anchorage of osseointegrated implants.

Amalgam tattoo versus melanocytic neoplasm - Differential diagnosis of dark pigmented oral mucosa lesions using infrared spectroscopy.

BACKGROUND: Dark pigmented lesions of the oral mucosa can represent a major diagnostic challenge. A biopsy is usually required to determine the nature of such intraoral discolorations. This study investigates the potential use of infrared spectroscopy for differential diagnosis of amalgam tattoos versus benign or malignant melanocytic neoplasms. MATERIALS AND METHODS: For this retrospective study, formalin-fixed paraffin-embedded tissue (FFPE) specimens of dark pigmented lesions concerning the oral mucosa or the lip were investigated using mid infrared spectroscopy. The samples were chosen from patients who had undergone a mucosal biopsy at the University Hospital Innsbruck (Austria) between the years 2000 and 2017. Principal component analysis was used for data exploration. Evaluation was based on the superimposition of the recorded spectra and the corresponding histologic slides. RESULTS: In total, 22 FFPE specimens were analyzed. Clear differences were found between amalgam and non-amalgam samples. A general weakening of the penetrating infrared radiation allowed for unspecific discrimination between these two classes. An overall accuracy in predicting the correct class of 95.24% was achieved. CONCLUSION: Infrared spectroscopy appears to be a suitable technique to differentiate between amalgam tattoos and melanocytic lesions in FFPE samples. It could potentially be applied in vivo, too, serving as a non-invasive diagnostic tool for intraoral dark pigmented lesions.

Effect of strontium surface-functionalized implants on early and late osseointegration: A histological, spectrometric and tomographic evaluation.

Numerous in vivo, in vitro and clinical studies report on beneficial effects of strontium with respect to increased bone growth. Based on this knowledge the aim of this study was to evaluate early and late osseointegration stages of functionalized titanium implants showing sustained release of strontium (Sr) and further investigate its potential systemic effect. Strontium functionalized (Ti-Sr-O) and Grade 4 (Control) titanium implants were inserted in the femoral condyle of New Zealand White rabbits. The Ti-Sr-O coating was characterized using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectrometry (EDX) for structure, coating thickness and chemical composition. Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) was used to evaluate released strontium in vitro while Atomic Absorption Spectrometry (AAS) was utilized to monitor serum levels of strontium and calcium. Additionally, histological and tomographic analysis of bone-to-implant contact (BIC%) and bone formation (BF%) was performed, following implantation periods of two or twelve weeks, respectively. Median values for BIC% for Ti-Sr-O revealed significant differences within the two- and twelve-week observation periods, while exceeding BF% was discovered especially after twelve weeks when performing the histological evaluation. The results from the micro-computed tomography (µ-CT) showed no significant differences, when comparing the experimental groups. AAS measurements did not indicate a systemic effect by the local strontium release. Within the limitations of the study, it was shown that a Ti-Sr-O coating with sustained release characteristics of strontium, accelerates bone apposition and represents a potential potent surface modification for endosseous medical implant devices. STATEMENT OF SIGNIFICANCE: This study presents first data with respect to early and late in vivo response on a strontium functionalized titanium surface comprising a nanotopography manufactured by a magnetron sputtering process. We investigated different osseointegration stages of screw-shaped implants with dental implant geometries in a rabbit femur model observing beneficial effects of the functionalized surface on bone-to-implant contact and bone formation caused by tailored release of the bone anabolic strontium. Histomorphometrical data revealed that a functionalized titanium surface with controlled liberation of strontium accelerates osseointegration while spectrometry measurements did not indicate a potential systemic effect of this osteoinductive agent and could thus have impact on modifications of medical implant devices.

Comparing the effect of strontium-functionalized and fluoride-modified surfaces on early osseointegration.

BACKGROUND: Studies have shown that medical devices comprising strontium contribute to bone healing and osseointegration. The aim of this study was to evaluate the in vivo performance of surface-functionalized implants (Ti-Sr-O) showing predictable release characteristics of strontium and compare it to performance a commercially available fluoride-modified surface. METHODS: Ti-Sr-O functionalized, fluoride-modified,  Grade 4 titanium implants were inserted in the femoral condyle of adult male New Zealand white rabbits. Atomic absorption spectrometry (AAS) was utilized to monitor strontium blood serum levels. Two weeks after insertion, histomorphometric evaluation was performed with respect to bone-to-implant contact (BIC%) and bone formation (BF%) using defined regions of interest. RESULTS: Mean values for BIC% showed a comparable degree of osseointegration for Ti-Sr-O and the fluoride-modified surface, while BF% revealed a significant difference in increased BF with Ti-Sr-O. AAS measurements did not indicate any influence of the Ti-Sr-O modified implants on the strontium blood serum concentrations. CONCLUSIONS: Within the limitations of this study, it was shown that the Ti-Sr-O coating, with sustained release characteristics of strontium, enhanced bone apposition and, thus, could find practical applications, e.g., within the field of medical implantology.

Bone regenerating effect of surface-functionalized titanium implants with sustained-release characteristics of strontium in ovariectomized rats.

Since strontium (Sr) is known for its anabolic and anticatabolic effect on bone, research has been focused on its potential impact on osseointegration. The objective of this study was to investigate the performance of nanotopographic implants with a Sr-functionalized titanium (Ti) coating (Ti-Sr-O) with respect to osseointegration in osteoporotic bone. The trial was designed to examine the effect of sustained-release characteristics of Sr in poor-quality bone. Three Ti-Sr-O groups, which differed from each other in coating thickness, Sr contents, and Sr release, were examined. These were prepared by a magnetron sputtering process and compared to uncoated grade 4 Ti. Composition, morphology, and mechanical stability of the coatings were analyzed, and Sr release data were gained from in vitro washout experiments. In vivo investigation was carried out in an osteoporotic rat model and analyzed histologically, 6 weeks and 12 weeks after implantation. Median values of bone-to-implant contact and new bone formation after 6 weeks were found to be 84.7% and 54.9% (best performing Sr group) as compared to 65.2% and 23.8% (grade 4 Ti reference), respectively. The 12-week observation period revealed 84.3% and 56.5% (best performing Sr group) and 81.3% and 39.4% (grade 4 Ti reference), respectively, for the same measurements. The increase in new bone formation was found to correlate with the amount of Sr released in vitro. The results indicate that sputtered nanostructured Ti-Sr-O coatings showed sustained release of Sr and accelerate osseointegration even in poor-quality bone, and thus, may have impact on practical applications for medical implants.

Osteoneogenesis due to periosteal elevation with degradable and nondegradable devices in Göttingen Minipigs.

INTRODUCTION: Periosteal distraction or elevation has been known as an experimental method to induce new bone formation. Although it uses the principles of distraction osteogenesis no further osteotomy is necessary. The purpose of this study was to test devices of different materials and to evaluate the point of origin of the new bone formation. MATERIAL & METHODS: On each calvaria of twelve male adult Göttingen Minipigs three devices were implanted. The materials used were degradable PDLLA (poly-DL-lactide), PGA (polyglycolic acid) and nondegradable Ti (titanium). After a consolidation time of 2, 4 and 6 weeks days a total of 36 specimens were harvested. To identify the total amount of newly created bone, micro-CT and histological analysis were performed. RESULTS: All degradable devices collapsed to a certain extent within the observation time but osteoneogenesis took place in all materials after a consolidation time of 2, 4 and 6 weeks after implantation above and under the devices. No statistical significant differences between the materials were found. However, most bone formation took place in the space under the periosteum and above the devices (p < 0.001). CONCLUSION: Periosteal elevation can produce new bone formation with degradable devices, which derives from the periosteum and the underlying bone. In this interaction the periosteum seems to contain the larger share.

Enhanced osseointegration of endosseous implants by predictable sustained release properties of strontium.

UNLABELLED: Studies have shown that strontium (Sr) incorporated into surfaces may enhance osseointegration. Thus, we suggested that a sustained Sr release from implant surfaces could improve bone healing. This study verifies and further investigates the effect of a novel Ti-Sr-O functionalized implant surface prepared from a magnetron co-sputtering platform with a continuous release of Sr. MATERIALS AND METHODS: Four experimental Ti-Sr-O groups, which differed from each other in Sr contents and pre-wash procedures, were tested. Implants were prepared with a Ti-Sr-O coating by means of magnetron co-sputtering and compared to Grade 4 titanium. Composition, morphology and mechanical stability were analyzed; Sr-release data were gained from in vitro washout experiments. In vivo investigations were carried out in a rat model and analyzed histologically regarding bone-to-implant contact and new bone formation 30 days after implantation. RESULTS: Structural differences were detected between the two basis Ti-Sr-O coatings with 6.7 at.% and 8.9 at.% Sr, respectively. Different release profiles were observed with 8.9 at.% Sr coating exhibiting the highest long-term release of Sr. Median values of new bone formation and bone-to-implant contact was found to be 60.1% and 91.6%, respectively, for the best group compared to 16.6% and 70.6% for the Grade 4 titanium reference. The increase in new bone formation was found to correlate with the amount of Sr released in vitro. CONCLUSION: The results show that sputtered Ti-Sr-O coatings with sustained release of Sr may improve osseointegration, and could thus have impact on practical applications for medical implants.

Accelerated bone ingrowth by local delivery of strontium from surface functionalized titanium implants.

Studies have indicated systemic treatment with strontium (Sr) as a potential route to increase bone quality and formation around osseointegrating implants. However, adverse effects are linked to such treatment. In this study we present a surface modification method designed for sustained local release of Sr from implants. The four groups used were prepared by a magnetron co-sputtering process and selected on the basis of Sr release data. The composition, morphology and mechanical stability of the coatings were analyzed and the Sr release profiles were investigated in vitro by washout experiments. Mesenchymal stem cells were cultured on the different coatings to evaluate potential cytotoxic effects and the effect on cellular proliferation. No indication of toxicity was found. A rodent study demonstrated a significant increase in direct bone-to-implant contact and peri-implant bone volume, for several of the groups, four weeks after implantation when compared to a Grade 4 titanium reference group. Median values of bone-to-implant contact and new bone formation was found to be 19% and 53%, respectively, for the best group compared to 0% for both parameters with respect to the Grade 4 titanium reference. The results indicate that this method may have applications within the orthopedic and dental industry.