RESUMO
The demand for high data rate transfer and large capacities of traffic is continuously growing as the world witnesses the development of the fifth generation (5G) of wireless communications with the fastest broadband speed yet and low latency [...].
RESUMO
In this study, a new design of a tri-band multiple-input-multiple-output (MIMO) antenna array is proposed for fifth-generation (5G) cellular systems. Its structure is composed of eight identical planar-inverted F antenna (PIFA) elements placed at different edge corners of the handset mainboard with overall dimensions of 150 × 75 mm2. The PIFA elements and ground plane of the MIMO antenna system are arranged on the back layer of the platform, which makes the design easy to integrate with the handset circuit. For S11 ≤ -10 dB, the radiation elements of the MIMO design operate at the frequency ranges of 2.5-2.7 GHz, 3.4-3.75 GHz, and 5.6-6 GHz covering the long-term evolution (LTE) 41, 42/43, and 47 operation bands, respectively. The array achieves better than 15 dB return loss results across the three operating bands. The presented antenna array not only exhibits multi-band operation but also generates the polarization diversity characteristic, which makes it suitable for multi-mode operation. The proposed antenna array was simulated and experimentally tested. Fundamental characteristics of the proposed design are investigated. It offers three band S-parameters with acceptable isolation and dual-polarized radiation with quite good efficiency and gain results. Besides this, the total active reflection coefficient (TARC) and envelope correlation coefficient (ECC) results of the PIFAs are very low over the bands. In addition, the radiation characteristics of the MIMO antenna in the presence of the user and handset components are studied. Moreover, a new and compact phased array millimeter-wave (MM-Wave) antenna with broad bandwidth and end-fire radiation is introduced which can be easily integrated into the smartphone antenna system. Due to its good performance and simple structures, the proposed smartphone antenna array design is a good candidate for future multi-mode 5G cellular applications.
RESUMO
A new ultra-wideband (UWB) multiple-input/multiple-output (MIMO) antenna system is proposed for future smartphones. The structure of the design comprises four identical pairs of compact microstrip-fed slot antennas with polarization diversity function that are placed symmetrically at different edge corners of the smartphone mainboard. Each antenna pair consists of an open-ended circular-ring slot radiator fed by two independently semi-arc-shaped microstrip-feeding lines exhibiting the polarization diversity characteristic. Therefore, in total, the proposed smartphone antenna design contains four horizontally-polarized and four vertically-polarized elements. The characteristics of the single-element dual-polarized UWB antenna and the proposed UWB-MIMO smartphone antenna are examined while using both experimental and simulated results. An impedance bandwidth of 2.5-10.2 GHz with 121% fractional bandwidth (FBW) is achieved for each element. However, for S11 ≤ -6 dB, this value is more than 130% (2.2-11 GHz). The proposed UWB-MIMO smartphone antenna system offers good isolation, dual-polarized function, full radiation coverage, and sufficient efficiency. Besides, the calculated diversity performances of the design in terms of the envelope correlation coefficient (ECC) and total active reflection coefficient (TARC) are very low over the entire operating band.
RESUMO
Differentially driven devices represent a highly promising research field for radio frequency (RF), microwave (MW), and millimeter-wave (mmWave) designers and engineers. Designs employing differential signals are essential elements in low-noise fourth-generation (4G) and fifth-generation (5G) communications. Apart from the conventional planar MW components, differential-fed balanced microstrip filters, as promising alternatives, have several advantages, including high common-mode rejection, low unwanted radiation levels, high noise immunity, and wideband harmonic suppression. In this paper, a comprehensive and in-depth review of the existing research on differential-fed microstrip filter designs are presented and discussed with a focus on recent advances in this research and the challenges facing the researchers. A comparison between different design techniques is presented and discussed in detail to provide the researchers with the advantages and disadvantages of each technique that could be of interest to a specific application. Challenges and future developments of balanced microstrip bandpass filters (BPFs) are also presented in this paper. Balanced filters surveyed include recent single-, dual-, tri-, and wide-band BPFs, which employ different design techniques and accomplish different performances for current and future wireless applications.
RESUMO
A very compact microstrip reconfigurable filter for fourth-generation (4G) and sub-6 GHz fifth-generation (5G) systems using a new hybrid co-simulation method is presented in this manuscript. The basic microstrip design uses three coupled line resonators with λ/4 open-circuited stubs. The coupling coefficients between the adjacent and non-adjacent resonators are used to tune the filter at the required center frequency to cover the frequency range from 2.5 to 3.8 GHz. The coupling coefficient factors between the adjacent resonators are adjusted to control and achieve the required bandwidth, while the input and output external quality factors are adjusted to ensure maximum power transfer between the input and output ports. Two varactor diodes and biasing circuit components are selected and designed to meet the targeted performance for the tunable filter. The impedance bandwidth is maintained between 95 and 115 MHz with measured return losses of more than 17 dB and measured insertion loss of less than 1 dB. Computer simulation technology (CST) is utilized to design and optimize the presented reconfigurable filter, with hybrid co-simulation technique, using both CST microwave studio (MWS) and CST design studio (DS), is applied to build the model by considering the SPICE representation for the varactor switches and all electronic elements of the biasing circuit. The introduced reconfigurable microstrip filter is also fabricated using a Rogers RO3010 material with a relative dielectric constant of 10.1 and it is printed on a very compact size of 13 × 8 × 0.81 mm3. An excellent agreement is obtained between the simulation and measurement performance.
RESUMO
In this study, we propose a design of a multi-band slot antenna array applicable for fourth-generation (4G) and fifth-generation (5G) smartphones. The design is composed of double-element square-ring slot radiators fed by microstrip-line structures for easy integration with radio frequency (RF)/microwave circuitry. The slot radiators are located on the corners of the smartphone printed circuit board (PCB) with an overall dimension of 75 × 150 mm². The proposed multiple-input multiple-output (MIMO) antenna is designed to meet the requirements of 4G and 5G mobile terminals with essential bandwidth for higher data rate applications. For -10 dB impedance bandwidth, each single-element of the proposed MIMO design can cover the frequency ranges of 2.5â»2.7 GHz (long-term evolution (LTE) 2600), 3.45â»3.8 GHz (LTE bands 42/43), and 5.00â»5.45 GHz (LTE band 46). However, for -6 dB impedance bandwidth, the radiation elements cover the frequency ranges of 2.45â»2.82 GHz, 3.35â»4.00 GHz, and 4.93â»5.73 GHz. By employing the microstrip feed lines at the four different sides of smartphone PCB, the isolation of the radiators has been enhanced and shows better than 17 dB isolation levels over all operational bands. The MIMO antenna is implemented on an FR-4 dielectric and provides good properties including S-parameters, efficiency, and radiation pattern coverage. The performance of the antenna is validated by measurements of the prototype. The simulation results for user-hand/user-head impacts and specific absorption rate (SAR) levels of the antenna are discussed, and good results are achieved. In addition, the antenna elements have the potential to be used as 8-element/dual-polarized resonators.