Printability, Thermal and Compressive Strength Properties of Cementitious Materials: A Comparative Study with Silica Fume and Limestone.

Over the past decade, 3D printing in the construction industry has received worldwide attention and developed rapidly. The research and development of cement and concrete products has also become quite well-established over the years, while other sustainable materials receive considerably lower attention in comparison. This study aims to investigate the influence of the two most commonly used sustainable cementitious materials i.e., silica fume and limestone powder, on printability, thermal and mechanical properties of fly ash-Portland cement blends. Ternary blends containing Portland cement, fly ash and silica fume or limestone powder are prepared, whereas phase change material (PCM) is introduced to improve the thermal behavior. Based on the rheological properties and concurrent 3D concrete printing, improved buildability of the modified mixtures is linked to their static yield stress. Anisotropic mechanical properties are observed for 3D printed specimens, while cast specimens exhibit a maximum 41% higher compressive strength due to better material compaction. It is clear from the results that addition of silica fume and limestone powder ranged from 5% to 10%, reducing the anisotropic mechanical properties (maximum 71% and 68% reduction in anisotropic factor, respectively) in the printed specimens. The PCM addition ranged from 5% to 10% and improved thermal performance of the mixtures, as measured by a decrease in thermal conductivity (9% and 13%) and an increase in volumetric heat capacity (9% and 10%), respectively. However, the PCM-containing mixtures show around 29% reduction in compressive strength, compared to the control specimen, which necessitates new material design considering matrix strengthening methods.

Microbiologically Induced Concrete Corrosion: A Concise Review of Assessment Methods, Effects, and Corrosion-Resistant Coating Materials.

Microbiologically induced concrete corrosion (in wastewater pipes) occurs mainly because of the diffusion of aggressive solutions and in situ production of sulfuric acid by microorganisms. The prevention of concrete biocorrosion usually requires modification of the mix design or the application of corrosion-resistant coatings, which requires a fundamental understanding of the corrosion process. In this regard, a state-of-the-art review on the subject is presented in this paper, which firstly details the mechanism of microbial deterioration, followed by assessment methods to characterize biocorrosion and its effects on concrete properties. Different types of corrosion-resistant coatings are also reviewed to prevent biocorrosion in concrete sewer and waste-water pipes. At the end, concluding remarks, research gaps, and future needs are discussed, which will help to overcome the challenges and possible environmental risks associated with biocorrosion.

Influence of Sugarcane Bagasse Ash and Silica Fume on the Mechanical and Durability Properties of Concrete.

Cement production is environmentally unsustainable due to the high anthropogenic carbon emissions produced. Supplementary cementitious materials (SCMs), derived from the by-products of different industries, have been deemed an effective way to reduce carbon emissions. The reduction in carbon emissions is achieved by lowering the clinker factor of cement, through a partial replacement with an SCM. Sugarcane Bagasse Ash (SCBA) is produced as an agricultural waste from the sugarcane industry and has gained a lot of attention for being a feasible and readily available pozzolanic material, underutilised as an SCM. This study evaluates alkali-activated sugarcane bagasse ash's mechanical and durability performance, at varied contents, in binary blended cement concrete and ternary blended cement concrete containing silica fume (SF). Potassium Hydroxide (KOH), used as the alkali activator, is intended to enhance the reactivity of the ash, with the possibility of a high-volume SCBA content. The mechanical performance was investigated by compressive and split tensile strength tests, and durability performance was investigated using the Oxygen Permeability Index (OPI) test. In addition, a micro-CT porosity test was conducted to assess how the microstructure and porosity of the concrete affect the mechanical and durability performance. The results indicated that using SCBA in a ternary blend with SF can significantly improve the overall performance and create less porous concrete. At 30% SCBA and 10% SF replacement, the performance tests revealed the highest mechanical strength and the lowest permeability, outperforming the control concrete and the binary blended cement concrete containing only SCBA.

Additive Manufacturing of Sustainable Construction Materials and Form-finding Structures: A Review on Recent Progresses.

Recently, there has been an increasing interest on the sustainability advantage of 3D concrete printing (3DCP), where the original cement-based mixtures used for printing could be replaced or incorporated with environmental-friendly materials. The development in digital modeling and design tools also creates a new realm of form-finding architecture for 3DCP, which is based on topological optimization of volumetric mass and physical performance. This review provides a perspective of using different green cementitious materials, applications of structural optimization, and modularization methods for realizing sustainable construction with additive manufacturing. The fresh and hardened mechanical properties of various sustainable materials for extrusion-based 3D printing are presented, followed by discussions on different topology optimization techniques. The current state of global research and industrial applications in 3DCP, along with the development of sustainable construction materials, is also summarized. Finally, research and practical gaps identified in this review lead to several recommendations on material developments, digital design tool's prospects for 3DCP to achieve the sustainability goal.

Strength Properties of Sustainable Mortar Containing Waste Steel Slag and Waste Clay Brick: Effect of Temperature.

The use of waste streams for the production of sustainable cement-based materials cannot be overemphasized. This study investigates the feasibility of reusing waste steel slag (WSS) and waste clay brick (WCB) as a replacement for natural sand (NS) in mortar. Numerous studies have reported mainly the compressive strength of concrete/mortar, while limited research is available that focuses on the tensile and flexural strength of mortar, and especially the performance at elevated temperature. Hence, this study investigates the tensile and flexural strength of mortar with three different replacement percentages (0, 50 and 100% by volume of NS) of NS by WSS and WCB at normal temperature (without thermal treatment) and after exposure to elevated temperatures (250, 400 and 600 °C). At ambient condition, both tensile and flexural strength were enhanced as the WSS content increased (76 and 68%, respectively, at 100% WSS). In comparison, the strength increased at 50% WCB (25 and 37%, accordingly) and decreased at 100% WCB (23 and 20%, respectively) compared to 100% NS. At elevated temperatures, both the tensile and flexural strength of mortar mixes decreased significantly at 600 °C.

Enhancement of Mechanical Properties and Porosity of Concrete Using Steel Slag Coarse Aggregate.

This paper investigates the possibility of utilizing steel slags produced in the steelmaking industry as an alternative to burnt clay brick aggregate (BA) in concrete. Within this context, physical, mechanical (i.e., compressive and splitting tensile strength), length change, and durability (porosity) tests were conducted on concrete made with nine different percentage replacements (0%, 10%, 20%, 30%, 40%, 50%, 60%, 80%, and 100% by volume of BA) of BA by induction of furnace steel slag aggregate (SSA). In addition, the chemical composition of aggregate through X-ray fluorescence (XRF) analysis and microstructural analysis through scanning electron microscopy (SEM) of aggregates and concrete were performed. The experimental results show that the physical and mechanical properties of concrete made with SSA were significantly higher than that of concrete made with BA. The compressive and tensile strength increased by 73% when SSA fully replaced BA. The expansion of concrete made with SSA was a bit higher than the concrete made with BA. Furthermore, a significant lower porosity was observed for concrete made with SSA than BA, which decreased by 40% for 100% SSA concrete than 100% BA concrete. The relation between compressive and tensile strength with the porosity of concrete mixes are in agreement with the relationships presented in the literature. This study demonstrates that SSA can be used as a full replacement of BA, which is economical, conserves the natural aggregate, and is sustainable building material since burning brick produces a lot of CO2.

The Effect of Material Fresh Properties and Process Parameters on Buildability and Interlayer Adhesion of 3D Printed Concrete.

The advent of digital concrete fabrication calls for advancing our understanding of the interaction of 3D printing with material rheology and print parameters, in addition to developing new measurement and control techniques. Thixotropy is the main challenge associated with printable material, which offers high yield strength and low viscosity. The higher the thixotropy, the better the shape stability and the higher buildability. However, exceeding a minimum value of thixotropy can cause high extrusion pressure and poor interface bond strength if the printing parameters are not optimized to the part design. This paper aims to investigate the effects of both material and process parameters on the buildability and inter-layer adhesion properties of 3D printed cementitious materials, produced with different thixotropy and print head standoff distances. Nano particles are used to increase the thixotropy and, in this context, a lower standoff distance is found to be useful for improving the bond strength. The low viscosity "control" sample is unaffected by the variation in standoff distances, which is attributed to its flowability and low yield stress characteristics that lead to strong interfacial bonding. This is supported by our microscopic observations.