Fabrication and superhydrophobic behavior of fluorinated microspheres.

We describe the preparation of fluorinated microspheres by precipitation polymerization and their use to fabricate superhydrophobic surfaces. For that purpose, two different approaches have been employed. In the first approach, a fluorinated monomer (either 4-fluorostyrene or 2,3,4,5,6-pentafluorostyrene) was added to the initial mixture of monomers constituted by styrene (S) and divinylbenzene (DVB). The second approach is based on the encapsulation of a block copolymer, polystyrene-b-poly(2,3,4,5,6-pentafluorostyrene), during the polymerization of the monomers (S and DVB), thus enabling the formation of particles with perfluorinated chains instead of single functional groups at the interface. Both approaches led to narrow polydisperse particles with fluoro-functional groups at the interface as demonstrated by scanning electron microscopy (SEM), infrared (IR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). Surface array of particles obtained by simple solvent casting presented superhydrophobic behavior with contact angles of water droplets of ca. 160-165°.

Design of polypeptide-functionalized polystyrene microspheres.

In this contribution, the principle of spontaneous surface segregation has been applied for the preparation of polypeptide-functionalized polystyrene microspheres. For that purpose, an amphiphilic diblock copolymer was introduced in the mixture styrene/divinylbenzene and polymerized using AIBN as initiator. During the polymerization, cross-linked particles were obtained in which the diblock copolymer was encapsulated. The amphiphilic diblock copolymers used throughout this study contain a hydrophilic polypeptide segment, either poly(L-lysine) or poly(L-glutamic acid) and a hydrophobic polystyrene block. After 4 h of polymerization, rather monodisperse particles with sizes of approximately 3-4 microm were obtained. Upon annealing in hot water, the hydrophilic polypeptides migrate to the interface, hence, either positively charged or neutral particles were obtained when poly(L-lysine) is revealed at the surface and exposed to acidic or basic pH, respectively. On the opposite, negatively charged particles were achieved in basic pH water by using poly(L-glutamic acid) as additive. The surface chemical composition was modified by changing the environment of the particles. Thus, exposure in toluene provoked a surface rearrangement, and due to its affinity, the polystyrene block reorients toward the interface.

Scaling properties of contact area of pressure-sensitive adhesives.

Two new devices were developed to provide accurate measurements of both the contact area and the tack strength of pressure-sensitive adhesives (PSAs). The first one is the "mechano-optical tack tester" (MOTT), which was designed to apply controlled contact pressure by means of a quartz prism probe, for determined contact times, onto the surfaces of PSA samples. The contact area is measured by the reflection of light at the quartz probe surface, which is in contact with the adhesive. The second device is an "acoustic contact tester" (ACT) that measures the tack strength and the contact area between a silicate glass and an adhesive by the reflection of an acoustic wave. Two ultrasonic sensors of different acoustic wavelengths have been built in order to study the scaling effects of the contact kinetics between an adhesive and the probe. MOTT and ACT experiments on a commercial PSA show that the contact area is the main parameter that governs the tack properties of the PSA. The experiments and the modeling point out that the contact area depends on the compression stress, the roughness, the thickness, and the Young's modulus of the PSA. However, comparison of contact kinetics from MOTT and ACT experiments show that the contact area is a subjective parameter that depends on the wavelength of the reflected beam used for its measurement.

Influence of surface and bulk structures of acrylic PSA films onto their tack properties.

PSA films are obtained by coalescence of latices synthesized by free-radical emulsion polymerization of methyl methacrylate (MMA) and 2-ethylhexyl acrylate (EHA). For the same overall 50/50 molar composition, the polymer particles have well-defined structures when the feed composition and the feed mode (using batch or semicontinuous processes) are adjusted. The characterizations of the film structures by surface (tapping mode AFM) and bulk (DSC, rheology) analyses argue for the conservation of the initial particle structure when coalescence occurs. The influence of the chemical heterogeneity on the tack properties of the films is investigated to extend the study of these original acrylic PSA films up to relevant structure-property correlations.

Amphiphilic diblock copolymers with adhesive properties: I. Structure and swelling with water.

We study asymmetric block copolymers with the simple diblock AB architecture, in the case where the longer block A is both hydrophobic and "soft", whereas the shorter block B is hydrophilic and "hard". Materials with such a particular combination of physico-chemical and mechanical properties have distinctive advantages, in particular for designing water-compatible adhesive materials. The phase diagram is established, combining NMR and SAXS characterisations of the materials. The swelling with water is monitored through gravimetry and "time-resolved" SAXS. Indications of maintained adhesive properties in a wet environment are given.

[Good tolerance and absence of immunologic effects in mice treated with arsenic-rich thermal water]. / Bonne tolérance et absence d'effets immunologiques chez la souris traitée par une eau thermale riche en arsenic.

Three strains of mice were given, per os and ad libitum, a spa water containing 6.8 mg/l arsenic and indicated for the treatment of allergic respiratory diseases or chronic bronchitis. The daily arsenic intake was approximately from 1.5 to 4 mg/kg. No effect on body weight gain or on the various immune parameters assessed was observed. These results demonstrate that this spa water, despite its high arsenic content, is not toxic and does not interfere with the immune system of healthy mice.