Experimental near infrared absorption enhancement of graphene layers in an optical resonant cavity.

Graphene has recently emerged as a promising candidate for a wide range of photonic and optoelectronic applications, with a high application potential in devices using infrared radiation. The optical absorption of 2D materials and graphene can be uniquely enhanced when they are embedded in optical resonant cavities, since optically-thin atomic-thickness absorbers do not perturb the cavity itself. Despite the many theoretical studies, experimental validation is still lagging behind. Here, large near infrared (NIR) absorption of unpatterned chemical vapor deposition graphene is experimentally demonstrated for the first time in a large area (1 inch) passive optical device by exploiting the enhancement of the electric field at the center of a Fabry-Perot cavity. Test devices were fabricated with single layer, double layer and five layers graphene, sandwiched between two almost symmetric Bragg mirrors deposited by radio frequency sputtering and consisting of alternate layers of Si and SiO2. A thin evaporated MgF2 overlayer was used to reduce sputtering induced damage on graphene layers. Measured absorption values, in the range of 37%-45%, were found in very good accordance with simulated ones. A maximum absorption of 45% was measured at 2345 nm for the double-layer graphene.

High-precision measurement of optical constants of ultra-thin coating using surface plasmon resonance spectroscopic ellipsometry in Otto-Bliokh configuration.

In this paper, a surface plasmon resonance (SPR) spectroscopic ellipsometry, based on Otto-Bliokh configuration, is developed for the measurement of thickness and optical constants of ultra-thin coatings. This technique combines sensitivity of surface plasmon with accessibility of optical constants and other advantages of ellipsometry. Surface plasmons (SP) are generated in the sample under test in total reflectance mode and SP geometric distribution over the sample surface is influenced by the coating thickness and optical properties on one hand, and by the air gap thickness on the other hand. Nanoscale control of the thickness of the air gap between a convex surface and the sample was assured using a micron-size beam spot irradiating the contact zone. The amplitude and phase change induced by SPR in the visible and near-infrared spectral range were obtained to determine the dispersion of optical constants and the thickness of the ultra-thin layer. The extracted optical constants were found to be in excellent agreement with the results obtained using TEM and XRR techniques. Both theoretical analysis and experimental results demonstrated high sensitivity and precision of the proposed technique for the analysis of coatings of both metals and dielectrics on metals.

Behavior of optical thin-film materials and coatings under proton and gamma irradiation.

Optical materials and coatings are exposed to the flux of energetic particles when used in either space applications or nuclear energy plants. The study of their behavior in such an environment is important to avoid failure of the optical components during their operation. The optical performance of several thin-film materials ((HfO2, Ta2O5, Nb2O5, TiO2, SiO2) and coatings, under irradiation with high-dose gamma rays (5.8 MGy) and exposure to low-energy (60 keV) protons, has been investigated. Some variations of optical properties have been detected in silicon oxide after irradiation, while the other materials are stable in such conditions.

Optical transmission filters for observation of lightning phenomena in the Earth atmosphere.

Very narrowband transmission filters, as parts of an instrument for the study of lightning phenomena, are described. Their performance must be maintained at an incidence angle of ±5.5° and this condition poses some limitations on the minimum bandwidth of the order of a few nanometers. The fabrication of such coatings on large area substrates is quite challenging because of the required thickness accuracy. Moreover, their performance should be not influenced by the environmental conditions in space.

Variable narrow-band transmission filters for spectrometry from space. 2. Fabrication process.

The optical components described here are variable narrow-band transmission filters, where the transmittance peak varies with the position along the surface of the filter itself. They allow the construction of ultracompact and low-weight spectrometers for space applications. The theoretical behavior of graded filters has been already investigated by the authors, for imaging spectrometry of the Earth surface. The application of graded filters to miniaturized instruments for planetary missions (Mercury) is considered. Experimental results on the fabrication of small-dimension variable transmission filters operating over a wide spectrum, from visible to near infrared, are reported.

Variable narrowband transmission filters with a wide rejection band for spectrometry.

Variable narrowband transmission filters are useful for the development of compact spectrometers. For this purpose the filter should be directly coupled to the detector and the wavelength of the transmission peak should move in one surface direction over a length of a few millimeters. To obtain both a wide measurement spectrum and high accuracy, the ratio of extreme operating wavelengths is required to be greater than 2:1 and the width of the transmission band narrower than 10 nm. A metal-dielectric variable transmission filter, with an operating range of 400-1000 nm, is proposed. The method for obtaining variable transmission filters, with dimensions of a few millimeters, is described.

Multilayer coatings on glass for painting protection and optimized color rendering.

Optical coatings offer a solution to the problem of damage to paintings, caused by ultraviolet and infrared radiation, by cutting radiation wavelengths outside the visible range. Simultaneously, these coatings can enhance an observer's viewing of the paintings by reducing the reflections from ordinary glass panes. All these functions should be performed by the same coating. The design of such a coating, as well as the evaluation of existing products, requires the definition of an appropriate merit function in which coating absorption, high transparency, and color rendering are combined.