Effect of the use of bromelain associated with bioactive glass-ceramic on dentin/adhesive interface.

OBJECTIVES: To evaluate the effect of bromelain associated with Biosilicate on the bond strength (BS) of a universal adhesive system to sound (SD) and caries-affected dentin (CAD), and on the proteolytic activity. MATERIALS AND METHODS: Cavities were prepared in 360 molars, half submitted to cariogenic challenge. Teeth were separated into groups (n=20): Control-No treatment; CHX-0.12% chlorhexidine; NaOCl-5% sodium hypochlorite; Br5%-5% bromelain; Br10%-10% bromelain; Bio-10% Biosilicate; NaOClBio-NaOCl+Bio; Br5%Bio-Br5%+Bio; Br10%Bio-Br10%+Bio. Following treatments, the adhesive system was applied, and cavities were restored. Samples were sectioned into sticks and stored at 37 °C for 24 h, 6 months, and 1 year. Microtensile BS (2-way ANOVA, Bonferroni's test, α=0.05), fracture patterns (SEM), and adhesive interfaces (TEM) were evaluated. Bacterial collagenase assay and in situ zymography were performed. RESULTS: In CAD, Br10% presented higher BS (p=0.0208) than Br5%Bio. Br5% presented higher BS (p=0.0033) after 6 months than after 24 h; and association of treatments, higher BS (p<0.05) after aging than after 24 h. Mixed fractures were the most prevalent. Association of treatments promoted a more uniform hybrid layer with embedded Bio particles. Experimental groups presented lower (p<0.0001) relative fluorescence units than Control. Bromelain, associated or not with Bio, showed collagenolytic degradation. CONCLUSIONS: Bromelain associated with Biosilicate did not affect the BS to SD. In CAD, Br5%Bio decreased immediate BS but had no long-term influence. This association decreased the proteolytic activity. CLINICAL RELEVANCE: Bromelain and Biosilicate may enhance the longevity of adhesive restorations by inhibiting endogenous proteases.

Effect of natural agents on the bond strength to eroded dentin.

OBJECTIVE: This study evaluated the effect of bromelain and propolis extract on the bond strength (BS) of a universal adhesive system to eroded dentin. MATERIALS AND METHODS: Sixty human molars with exposed dentin were halved, with one half protected by composite resin and the other subjected to erosive treatment followed by remineralization. After the erosive treatment, the composite resin was removed, and the teeth were randomly assigned to three groups (n = 20): Adhesive-Control System; Br-10%; Pr-16%. Following the treatments, composite resin blocks were built on the dentin surfaces and sticks of 0.9 mm2 were obtained and stored in distilled water at 37°C for 24 h and 6 months. After these periods, the sticks underwent bond strength testing and the data were analyzed using 2-way ANOVA, Bonferroni test, p < 0.05. Fracture patterns were observed using light microscope and scanning electron microscopy. RESULTS: Irrespective of the substrate and aging duration, propolis demonstrated higher BS (p < 0.05) compared to the other treatments. Eroded dentin exhibited greater removal of the smear layer and dentinal tubules with a larger diameter than sound dentin, especially when treated with bromelain, resulting in the formation of resin tags. CONCLUSIONS: Propolis consistently promoted the highest bond strength, irrespective of aging or substrate. Eroded dentin treated with propolis, or bromelain exhibited a higher prevalence of non-adhesive fractures and resin tag formation. CLINICAL SIGNIFICANCE: Propolis shows promise for enhancing the longevity of adhesive restorations in eroded dentin due to its ability to promote high bond strength.

Different surface treatments on recently introduced CAD-CAM resin-modified ceramics: Implications on bond strength.

STATEMENT OF PROBLEM: The diverse chemical composition of recently introduced resin-modified ceramics complicates the establishment of a universally accepted clinical bonding protocol. PURPOSE: The purpose of this in vitro study was to evaluate the influence of different surface treatments of resin-modified ceramics on the bond strength to a resin cement. MATERIAL AND METHODS: Sixteen 10×12×3-mm resin-modified ceramic slices were obtained from each material (Cerasmart; GC, Shofu Block HC; Shofu, Vita Enamic; Vita, Evolux hybrid; BlueDent, Alium; Alium). Slices were assigned to 4 groups based on surface treatments: Control (no treatment), airborne-particle abrasion with Al2O3 (Al2O3), conditioning with 9% HF (HF), and Al2O3+HF. After treatments and silane coupling agent (Monobond N; Ivoclar) application, 7 resin cement cylinders (Choice 2 veneer; Bisco) were built on each slice and light polymerized for 20 seconds. Half of the specimens (n=14 cylinders) were stored for 24 hours, and the other half were thermocycled (20 000 cycles, 5 °C to 55 °C, 30-second dwell time). Microshear bond strength was tested and analyzed with 3-way ANOVA and the Tukey HSD test (α=.05), and failure patterns were classified. Surface morphology after treatments was observed with scanning electron microscopy and Raman spectroscopy. RESULTS: After 24 hours, all treatments induced higher bond strength (P<.05) than in the control in Evolux. Al2O3+HF caused higher bond strength (P<.05) than in the control in Cerasmart and Shofu, and higher bond strength than Al2O3 in Cerasmart. However, it resulted in lower bond strength (P<.05) than Al2O3 in Alium. After thermocycling, irrespective of the resin-modified ceramic, all treatments induced higher bond strength (P<.05) than in the control. HF induced lower bond strength (P<.05) than Al2O3 in Alium. Al2O3+HF caused the highest bond strength (P<.05) in Evolux and higher bond strength (P<.05) than HF in Vita Enamic. Adhesive failures were prevalent under control conditions, and mixed failures were common after treatments. Al2O3 induced surface alterations in all resin-modified ceramics. HF notably altered Vita Enamic, while it had no noticeable impact on the other resin-modified ceramics. Al2O3+HF caused a considerable alteration in Vita Enamic and modified the other resin-modified ceramics. Vita Enamic had the characteristic vibrational bands of inorganic compounds, while the other resin-modified ceramics exhibited distinct bands associated with organic compounds. CONCLUSIONS: Airborne-particle abrasion with Al2O3 followed by HF yielded the highest bond strength, regardless of the resin-modified ceramic, except for Alium, which demonstrated better bond strength after airborne-particle abrasion with Al2O3. 9% HF for 30 seconds caused notable surface alterations in Vita Enamic, negatively impacting its bond strength. Vita Enamic was the only resin-modified ceramic displaying both organic and inorganic composition, while the other resin-modified ceramics showed predominantly organic composition.

Effect of limonene associated with bioactive glass-ceramic on dentin/adhesive interface.

This study evaluated the effect of pretreatment with limonene and/or biosilicate on the bond strength of a universal adhesive system in self-etch mode to dentin. Occlusal cavities were prepared in 80 human molars and the teeth were randomly allocated to one of four groups (n = 20), according to the pretreatment regimens applied before the adhesive. The pretreatments were (i) Control, no pretreatment, (ii) LIM, 0.5% limonene; (iii) Bio, 10% biosilicate; and (iv) LIMBio, LIM + Bio. After adhesive application and restoration, the specimens were sectioned into sticks, separated, and stored in distilled water at 37°C for 24 h or 6 months. Microtensile bond strength test was carried out and measurements were compared across pretreatment groups and storage times. Fracture patterns and adhesive interfaces were observed. Loss of dry mass was calculated (n = 10). There was no statistically significant difference in the bond strength between the groups and the most prevalent fracture pattern was the non-adhesive. LIM and LIMBio resulted in more open dentinal tubules. LIM and Bio, whether separate or combined, showed particles of those substances, which decreased in size and number after 6 months. All groups lost mass weight after treatment, with no statistically significant differences between them. Limonene and biosilicate pretreatment did not affect the bond strength to dentin of the universal adhesive system, but resulted in more non-adhesive fractures, even after 6 months.

The effect of phytosphingosine associated with tooth brushing on color change, surface roughness, and microhardness of dental enamel - an in vitro and in situ study.

OBJECTIVE: This study evaluated the in vitro and in situ effects of phytosphingosine (PHS) associated with tooth brushing on color stability, surface roughness, and microhardness of dental enamel. METHODS: Sixty-four specimens of bovine teeth (6 × 6 × 2 mm) were separated into 8 groups (n = 8): S + TB: PHS (spray) + tooth brushing; TB + S: tooth brushing + PHS (spray); I + TB: PHS (immersion) + tooth brushing; TB + I: tooth brushing + PHS (immersion); TB: tooth brushing; S: PHS spray; I: immersion in PHS solution, and Saliva: immersion in saliva. Tooth brushing simulation (Mavtec, Brazil) was performed (356 rpm on 3.8 cm area by the toothbrush - Soft Tek) for 1, 7, 15, and 30 days. PHS remained in contact with specimens for 15 min. The specimens were evaluated before and after tooth brushing for color alteration (Easy Shade, VITA), and surface roughness (Model SJ-201P Mitutoyo), and Knoop microhardness (HMV-2, Shimadzu Corporation). For the in situ analyses, 8 participants were recruited and received an intraoral device with 6 fragments of bovine enamel (6 × 6 × 2 mm). The properties evaluated were the same as those of the in vitro study. Participants were randomized following best results of in vitro tested protocols, for 15 days: TB, TB + S, I + TB. Data obtained by in vitro (two-way ANOVA, Tukey, p < .05) and in situ (one-way ANOVA, Tukey, p < .05) studies were analyzed. RESULTS: The in vitro study showed that greater color change was found after 30 days. The greatest differences in surface roughness occurred between the initial value and after 1 day. Regarding microhardness, the highest values occurred after 15 and 30 days, which showed similar results. The in situ study showed greater color changes for the TB and I + TB, and greater surface roughness changes for TB as well as a similar increase in microhardness for the PHS protocols, which were higher than TB. CONCLUSIONS: Phytosphingosine leads to an increase in performance regarding color stability, surface roughness, and microhardness when applied. In general, the application of PHS after brushing showed a positive impact on its performance. CLINICAL RELEVANCE: Phytosphingosine proved to be interesting for compound prevention formulations in the dentistry field.

Remineralization, color stability and surface roughness of tooth enamel brushed with activated charcoal-based products.

OBJECTIVE: To evaluate the effect of activated charcoal-based (AC) products on color alteration, remineralizing potential and surface roughness of dental enamel. MATERIALS AND METHODS: Bovine incisors were cut into 6 × 6 × 2 mm fragments. Initial color (EasyShade, Vita) and surface roughness (Surfcorder SE1700, Kosakalab) readings were performed. Fragments were separated into five groups (n = 17) according to the treatment: Control: Fluoride toothpaste (Colgate Total 12, Colgate); Charcoal + NaF: AC toothpaste (ACT) with sodium fluoride (Colgate Natural Extracts, Colgate); Charcoal + MFP + n-HA: ACT with sodium monofluorophosphate and nanohydroxyapatite (Black is White, Curaprox); Charcoal: Fluoride-free ACT (ProActive, Hinode); and Charcoal powder: AC powder. Simulated toothbrushing was performed and final color and surface roughness readings were obtained. Fragments were then polished, and initial microhardness (HMV-2, Shimatzu) readings were done. Samples were artificially demineralized and brushed again. Final microhardness readings were taken. Data were statistically analyzed. RESULTS: Fluoride-free charcoal presented the lowest surface roughness alteration (p < 0.05). Charcoal powder had the lowest color change (p < 0.05) and negative values for whiteness index for dentistry alteration. All the groups presented values below whiteness acceptability threshold and negative relative microhardness values. Control showed the highest remineralizing potential (p < 0.05). CONCLUSIONS: ACPs did not produce color alteration different from the fluoride toothpaste, except for Charcoal powder that caused less color change. ACPs caused surface roughness alteration similar to the fluoride toothpaste. ACT with fluoride and AC powder did not have remineralizing potential. CLINICAL SIGNIFICANCE: Activated charcoal-based products (ACP) promise effective tooth whitening and quick results, without teeth damage. In addition, some ACPs contain fluoride in toothpaste composition and promise rehardening potential. However, ACPs are not as effective as other whitening agents and can alter the surface roughness of the enamel. Even if the ACPs contain fluoride or other remineralizing agents, they might be ineffective.

Color stability and microhardness alteration of irradiated dental enamel treated with a high fluoride concentration toothpaste.

OBJECTIVES: Radiotherapy (RT) is a kind of head and neck cancer (HNC) treatment, which is associated to the habit of smoking and can develop collateral effects in the oral cavity, such as the increase of caries prevalence. This study evaluated the color alteration, the microhardness, and the remineralizing potential of high fluoride concentration toothpastes on irradiated teeth. MATERIALS AND METHODS: Forty bovine teeth were used (6 × 6 × 2 mm) and after color (EasyShade, VITA) and microhardness initial readings were separated into two groups: exposed to cigarette smoke and non-exposed. All samples were submitted to RT (30 Gy) and to cariogenic challenge. New color and microhardness readings were done. After RT (60 Gy), the samples were submitted to simulated toothbrushing (73,000 cycles = 5 years of brushing) with two different toothpastes: conventional (1450 ppm) and high fluoride concentration (5000 ppm). Final color and microhardness readings were done after brushing. Data were analyzed with 2-way ANOVA with repeated measures and Tukey's test (p < .05). RESULTS: There was no color difference after RT, nor after brushing (p > .05). However, after brushing, microhardness values increased for the samples treated with high fluoride concentration toothpaste (p < .05). CONCLUSION: Radiotherapy did not influence the teeth color, and the high fluoride concentration toothpaste presented remineralizing potential; therefore, it could be used on the caries prevention related to HNC radiation. CLINICAL RELEVANCE: Considering its remineralizing potential, toothpastes with high fluoride concentration could be a proper alternative for caries prevention in patients undergoing radiotherapy.

Whitening effect of 35% hydrogen peroxide in simulation of tooth with orthodontic bracket.

OBJECTIVE: To evaluate the color change and tooth whitening perception in 2 and 3 mm dental specimens simulating the orthodontic bracket for a 14-day period. MATERIALS AND METHODS: Forty bovine tooth fragments (8 × 7 mm) of 2 mm (G2, n = 20) and 3 mm (G3, n = 20) were divided into Control (C: without bracket simulation and whitening) and Experimental (E: with composite resin simulating orthodontic bracket cementation area). Analyses of color change (ΔE00 ) and perception of tooth whitening (WID ) were performed before (T0 ) and after (T1 ) the first bleaching session; before (T2 ) and after (T3 ) the second bleaching session; and after 7 days of the second bleaching session (T4 ). RESULTS: After 14 days (T4), ΔE00 and WID showed similarity results, except for G2C and G3E. The thickness did not influence the ΔE00 and WID (G2C = G3C and G2E = G3E). The presence of orthodontic bracket did not interfere in the color change or tooth whitening perception after 14 days, except for comparison of G2C and G3E. Additionally, dentin thickness did not influence the color change. CLINICAL SIGNIFICANCE: Teeth with orthodontic brackets showed similar color change and whitening perception to teeth without orthodontic bracket, but it is not influenced by dentin thickness.

Dentin µTBS and Hardness of Bulk-fill and Conventional Composites Placed in a Box-shaped Cavity Preparation.

PURPOSE: To compare the dentin microtensile bond strength (µTBS) and the Knoop hardness of bulk-fill and conventional restorative composites in box-shaped Class I cavities using different insertion techniques. MATERIALS AND METHODS: Forty box-shaped Class I preparatons 4 mm deep were performed in the pulp chamber of sound human third molars. The restorations were made using either a conventional microhybrid (Z250, 3M ESPE) or bulk-fill (Tetric EvoCeram Bulk-fill, TCBF) composite using two incremental thicknesses: 2 mm or 4 mm (n = 10). After 24-h water storage, the restorations were sectioned. The first slice (0.7 mm thick) taken from a proximal surface was submitted to the Knoop hardness (KHN) test at five depths from the occlusal cavosurface to the pulpal line angle. Sticks were fabricated from the remaining sections and tested for dentin microtensile bond strength (µTBS). Means were analyzed using two-way ANOVA and Tukey's test (p < 0.05). RESULTS: Higher (p < 0.05) µTBS resulted when both composites were restored with 2-mm increments, with no significant difference between materials (p > 0.05). Higher (p < 0.05) KHN means were found when 2-mm increments were used, with no significant differences (p > 0.05) between the materials. When the teeth were restored with one bulk increment (4 mm), the deeper layers presented lower KHN means (p < 0.05) starting at 2 mm for Z250 and 3 mm for TCBF. CONCLUSION: The 2-mm increment restorations in box-shaped cavities yielded higher µTBS and microhardness for conventional and bulk-fill composites.

The effect of proanthocyanidins and chlorhexidine on the bond strength of glass fiber posts to root dentin.

In this study, the influence of different irrigant solutions applied before cementation on the bond strength (BS) of glass fiber posts to root dentin was evaluated. Thirty endodontically treated maxillary canines of similar length were selected and divided into 3 groups (n = 10) according to the irrigant solution used before post cementation: 1% sodium hypochlorite (NaOCl; control), 2% chlorhexidine (CHX), or a 6.5% grape seed extract (GSE) cross-linking agent. After cementation of the posts, the roots were transversely sectioned to create 2 discs (2 mm) for each of the root thirds: coronal, middle, and apical. These discs were submitted to push-out tests (0.5 mm/min) to evaluate the BS between the glass fiber posts and the root dentin. Statistical analysis was performed by a 2-way analysis of variance and a Tukey test (P < 0.05). The failure mode was evaluated in all specimens. Both the CHX and GSE groups presented significantly higher BS values than the control group in all root thirds (P < 0.05). The values of the GSE group were significantly higher than those of the CHX group in all thirds except the apical third (P < 0.05). In the control group, the BS value was highest in the cervical third. There was no significant difference in the BS values between the cervical and middle thirds when CHX was used (P > 0.05); however, the BS value diminished significantly in the apical third (P < 0.05). The highest BS value in the GSE group was found in the middle third. The results showed that the use of either GSE or CHX before adhesive cementation improved the BS of glass fiber posts to root dentin.

Effect of bleaching agent and topical fluoride application on color and gloss of dental ceramics.

The aim of this study was to evaluate the effect of 16% carbamide peroxide and 1.23% acidulated phosphate fluoride application and their association with a change in color (ΔE*) and brightness of dental ceramic submitted to different finishing procedures. A total of 120 test specimens were fabricated and randomly divided into 3 groups (n = 40) according to the type of finishing: glazing; polishing; or polishing and glazing. Initial color and brightness readouts were taken, and the finished specimens were divided into groups (n = 10) according to the treatment to which they were submitted: fluoride; bleaching; bleaching and fluoride; or control. After this, final color and brightness readouts were taken. The type of polishing had no influence on ΔE* or brightness (P > 0.05). Regardless of which solution was used, a decrease in brightness occurred only for the group treated with bleach and fluoride (P < 0.05). The results showed the use of fluoride after bleaching may interfere with the esthetics of a restoration.

Influence of activation mode of resin cement on the shade of porcelain veneers.

PURPOSE: The aim of this study was to evaluate the influence of resin luting cement's activation mode in the final shade of porcelain veneers after accelerated artificial aging (AAA). MATERIALS AND METHODS: Porcelain veneers (IPS Empress Esthetic) were produced using a standardized shade (ET1) and thickness (0.6 mm). Twenty bovine teeth were collected, prepared, and divided into two groups: group I (n = 10)-light-cured group, only base paste was applied to the veneers; group II (n = 10)-dual-cured group, in which the same base paste used in group I and a transparent catalyst were proportionally mixed for 20 seconds and then applied to the veneers. The specimens were light-cured for 60 seconds each and were next subjected to AAA. They were submitted to color readings with a spectrophotometer in three instances: in the tooth surface (only the substrate), after the cementation and polymerization of the veneers, and after the AAA. The values of L*, a*, and b* were obtained and the total color change was calculated (∆E*). Values obtained were subjected to statistical analysis, with a significance of 0.05. RESULTS: There were no significant differences between dual- and light-cured modes considering ∆E*, L*, a*, and b* values obtained after aging (p > 0.05). Within the dual-cured mode there were no significant differences in ∆E*, L*, a*, and b* values (p > 0.05). CONCLUSION: No relevant differences were found between the two activation modes in color change. When submitted to aging, dual- and light-cured modes of the resin cement showed visually perceptible (∆E* > 1.0) color changes; however, within the threshold of clinical acceptance (∆E* > 3.3).

Development and effect of orodispersible film incorporated with Biosilicate for remineralization of dental enamel subjected to cariogenic and erosive challenge.

OBJECTIVES: The objective of this in vitro study was to assess the efficiency of incorporating Biosilicate particles (30 and 50 mg) into an experimental orodispersible film and its efficacy in the remineralization process of bovine dental enamel under cariogenic and erosive challenges. METHODS: Ninety-nine intact incisors, devoid of cracks or fractures, yielding 198 samples (6 × 6 × 2 mm) via vestibular sectioning using a low-speed diamond disc under water cooling. After flattening the enamel surface with 600, 1200, and 2000 grit sandpaper, the samples were divided into two groups based on the challenges they underwent: cariogenic (0.1 M lactic acid at pH 5.0) or erosive (0.05 M citric acid solution at pH 2.3). Samples from each challenge were further categorized into 11 groups (n = 9) according to the duration of cariogenic (3, 7, and 14 days) or erosive (3, 7, and 10 days) challenge, along with positive control groups (fragments untreated with challenges and treated with different Biosilicate concentrations) and negative controls (fragments treated with artificial saliva for the same periods established for cariogenic and erosive challenges). Treatments with orodispersible films containing Biosilicate (30 and 50 mg) were administered for 2 min per day for 15 days. RESULTS: The highest remineralizing potential was observed in samples treated with Biosilicate after 14 days of cariogenic challenge, irrespective of the concentration tested. For samples subjected to erosive challenge, erosion time did not affect Biosilicate's remineralizing potential. CONCLUSION: Biosilicate shows promise in terms of remineralizing potential in enamel subjected to cariogenic challenge due to its ability to form hydroxycarbonapatite in mineralized tissues.

Staining susceptibility of new calcium aluminate cement (EndoBinder) in teeth: a 1-year in vitro study.

AIM: To evaluate the staining susceptibility of new calcium aluminate cement (EndoBinder, EB) in teeth, with or without radiopacifying agent, in comparison with mineral trioxide aggregate (MTA). MATERIALS AND METHODS: Forty bovine incisors were used. After biomechanical preparation and filling, 2 mm of their fillings were removed for cervical plug fabrication (n = 10): EB without radiopacifier; EndoBinder + Bismuth Oxide (EBBO); Gray mineral trioxide aggregate (GMTA) and White mineral trioxide aggregate (WMTA). After teeth restoration, initial color readout was taken (Easyshade - CIE Lab) on the vestibular face. The teeth were stored in artificial saliva at 37°C for 1 year, and after time intervals of 30, 180, and 360 days, new color readouts were taken to determine color alteration (ΔE) in comparison with the initial readout (baseline). RESULTS: The results (2-way anova repeated measures, Bonferroni - P < 0.05) demonstrated that after 360 days, all groups presented ΔE above the clinically accepted limit (ΔE ≥ 3.3), however, without significant difference among them (P > 0.05). All groups presented decrease in ΔL values over the course of time, and the greatest variation occurred for WMTA, with significant difference in comparison with EB and EBBO (P < 0.05). CONCLUSIONS: Some negative features of MTA, such as the high incidence of dental structures staining justify the development of new materials. GMTA, WMTA, and EB with and without radiopacifying agent displayed color alteration (ΔE) after 360 days; however, the luminosity change (ΔL) was lower in EB in comparison with GMTA and WMTA.

Effect of artificial accelerated aging on the optical properties and monomeric conversion of composites used after expiration date.

This study sought to evaluate how artificial accelerated aging (AAA) affected color stability (ΔE), opacity (ΔOP), and degree of conversion (DOC) for 3 composite materials (Tetric Ceram, Tetric Ceram HB, and Tetric Flow) used both 180 days before and 180 days after their expiration dates. To evaluate the materials' optical properties, 10 specimens of each composite-5 prior to expiration and 5 after the materials' expiration date-were made in a teflon matrix. After polishing, the specimens were submitted to initial color and opacity readings and submitted to AAA for 384 hours; at that point, new readings were taken to determine ΔE and ΔOP. To evaluate monomeric conversion evaluation, 6 specimens from each composite and expiration date-3 prior to AAA and 3 after-were submitted to DOC analysis. Results of the 2-way ANOVA and Bonferroni's tests (P < 0.05) demonstrated that all composites had ΔE values above the clinically acceptable level (ΔE ≥ 3.3). When expiration dates were compared, only Tetric Flow showed a statistically significant difference (P < 0.05). Regardless of the expiration date, ΔOP values for all composites increased after AAA, but not significantly (P > 0.05). The expired Tetric Flow had the highest DOC values (71.42% ± 4.21) before AAA, significantly different than that of the other composites (P > 0.05). It was concluded that both expiration date and AAA affected the properties of the composites tested.

Long-term effect of firing protocols on surface roughness and flexural strength of lithium disilicate glass-ceramic.

This study evaluated the effect of different firing protocols on the surface roughness and flexural strength of CAD/CAM lithium disilicate glass-ceramic (LD) after aging methods. Forty-two LD bars of 16 x 4 x 2 mm (IPS e-max CAD, Ivoclar) were randomly separated into two groups according to firing protocols: Single firing-Staining, glazing, and crystallization in a single step; Multiple firings-Crystallization+First staining+Firing+Second staining+Firing+Glazing+Firing. After protocols, initial surface roughness readings were taken (Surfcorder SE1700, Kosakalab). Samples were then randomly separated into three groups (n=7) according to the aging methods they were submitted: Thermomechanical cycling (TMC, ER System, Erios, 1,200,000 cycles, 0.3 MPa, 2 Hz and 5°C/37°C/55°C, 30 s swell time); Simulated toothbrushing (STB, Pepsodent, MAVTEC, 73,000 cycles), and Control (no aging). Final surface roughness readings were done, and samples were submitted to a three-point bending test (OM100, Odeme Dental Research) and fractographic analysis by scanning electron microscopy (EVO-MA10, ZEISS). Data were analyzed (2-way ANOVA, (α=.05). There was no difference (p>.05) in the flexural strength between the firing protocols, regardless of the aging method. STB decreased the flexural strength of samples submitted to multiple firings, different from control (p<.05). Without aging (Control), before TMC, and after STB, LD had lower surface roughness when submitted to multiple firings than to single firing (p<.05). The firing protocols did not affect the flexural strength or the surface roughness of the lithium disilicate glass-ceramic, even after aging. However, toothbrushing negatively affected the flexural strength and smoothed the surface of the ceramic submitted to multiple firings.

The effect of Phytosphingosine and bioactive glass-ceramics in preventing dental enamel erosion.

This study evaluated the effect of phytosphingosine (PHS) and bioactive glass-ceramic (Biosilicate) on dental enamel in terms of color alteration (ΔE), microhardness, and surface roughness when submitted to erosive challenge (EC). Sixty specimens of bovine teeth (6×6×2mm) were obtained. Initial color (Easyshade, VITA), KHN (HMV-2, Shimadzu), and Ra (SJ-201P, Mitutoyo) measurements were performed. Specimens were separated into groups according to treatments: PHS, 10% Biosilicate, PHS+10% Biosilicate, and artificial saliva (control) and submitted to EC with Coca-Cola for 2 min. This cycle was repeated 4 times daily/15 days. Between cycles, specimens remained in artificial saliva (2 h/37°C). After daily cycles, they were also stored in artificial saliva at 37ºC. Final color, microhardness, and surface roughness measurements were done. Color and KHN data were analyzed by one-way ANOVA, Tukey's test; and Ra, by 2-way ANOVA, repeated measures, and Tukey's test (p<.05). The highest ΔE occurred in Saliva+EC (p<.05). Groups treated with PHS presented lower color change than Saliva+EC (p<.05). All the groups presented mean values above the 50:50% perceptibility (50:50%PT) and acceptability (50:50%AT) thresholds, except for control that showed mean value above 50:50%PT but below 50:50%AT. Biosilicate+EC showed higher relative microhardness than Saliva+EC (p<.05), but was similar to PHS+EC and PHS+Biosilicate+EC. Final enamel surface roughness increased for all the groups (p<.05), except for the control. The Biosilicate may prevent enamel mineral loss induced by erosion better than saliva. The PHS associated or not to Biosilicate demonstrated better color stability than saliva.

Antimicrobial effect of phytosphingosine in acrylic resin.

This study evaluated color stability (CS), anti-adherence effect (AAE), and cell viability of microorganisms on acrylic resin (AR) surface, treated associated or not with sodium percarbonate (SP). AR specimens were prepared, and color analysis was performed before and after the treatments and the CS was calculated. For analysis of AAE, the samples were sterilized by radiation in a microwave oven. Then samples were randomly distributed: phosphate-buffered saline (PBS - control), 0.5% sodium hypochlorite (SH), phytosphingosine (PHS), and phytosphingosine + SP (PHS+Na2CO3). The specimens remained in contact with solutions for 30 minutes and were later contaminated by Candida albicans. Aliquots were seeded in Petri dishes with Sabouraud Dextrose agar and incubated at 37°C for 24 hours. After the incubation, the number of colonies was counted. The cell viability of adhered microorganisms on the AR was evaluated and 20 fields were observed under an epifluorescence microscope, and the percentage of adhered viable cells was calculated. Data were compared (One-way ANOVA, Tukey, p<.05). As for CS, PHS+ Na2CO3 (0.4±0.1) resulted in less change than PBS (0.9±0.2), similar to the other groups (SH [1.0±0.3)]; PHS [0.9±0.2)]). There was no difference for all tested solutions regarding the ability to avoid microorganism adherence (p>0.05), but PHS (11.2±4.1) resulted in a smaller area of adhered viable cells, statistically different from SH (18.2±7.6) and PBS (26.4±10.8). It was concluded that PHS resulted in lower adhered viable cells and when associated with Na2CO3, also shows a lower effect on the CS of AR.

Incorporation of bioactive glass-ceramic into coconut oil for remineralization of incipient carious lesions.

This study evaluated the efficacy of incorporating different concentrations of bioactive glass-ceramic (Biosilicate) into coconut oil on the remineralizing potential and surface roughness of white spot lesions. Fragments (6 x 6 x 2mm) of bovine teeth were sectioned and initial microhardness (KHN) and surface roughness (Ra) readings were obtained. The samples were submitted to cariogenic challenge to form white spot lesions and were separated into six groups (n=13): 1) Artificial Saliva (AS); 2) Coconut Oil (CO); 3) CO+2% Biosilicate (CO+2%Bio); 4) CO+5% Biosilicate (CO+5%Bio); 5) 2% Biosilicate Suspension (2% Bio) and 6) 5% Biosilicate Suspension (5% Bio). The treatments for 1 cycle/day were: immersion into the treatments for 5 minutes, rinsing in distilled water, and storage in artificial saliva at 37ºC. After 14 days, KHN and Ra readings were taken. The surface roughness alteration ((Ra) was analyzed (Kruskal-Wallis, Dunn's post-test, p<0.05). CO+2%Bio had higher (p = 0.0013) (Ra followed by CO+5%Bio (p = 0.0244) than AS. The relative KHN and remineralization potential were analyzed (ANOVA, Tukey, p<0.05), and 5% Bio treatment presented a higher relative microhardness than all other groups (p>0.05). The remineralizing potential of all the treatments was similar (p > .05). When Biosilicate was added, the pH of the suspensions increased and the alkaline pH remained during the analysis. Biosilicate suspension is more efficient than the incorporation of particles into coconut oil at white spot lesion treatment. In addition to the benefits that coconut oil and Biosilicate present separately, their association can enhance the remineralizing potential of Biosilicate.

Influence of increment thickness on the similarity of composite shade: a pilot study.

The aim of this study was to evaluate the similarity in shade between increments of different composite thicknesses. Fifty test specimens 12 mm in diameter were fabricated and separated into five groups (n = 10) according to sample thickness: 0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Specimens were polished with water abrasive papers and silicone points. Next, based on the CIE L*a*b* system, test specimens were submitted to color readouts, and the values obtained for the coordinates L*, a*, and b* for each thickness were compared using one-way ANOVA and a Tukey test (P < 0.05). The results demonstrated that there was a reduction in coordinate L* as the test specimen thickness increased, with statistically significant differences (P < 0.05), except for 2.0 mm and 2.5 mm thicknesses (P > 0.05). Samples 1.5 mm thick presented less variation of a*, while a greater variation occurred for samples 2.5 mm thick, with a significant difference in comparison with the other thicknesses (P < 0.05), except for 2.0 mm (P > 0.05). Samples 0.5 mm thick presented a greater variation of b*, while the lowest variation in this coordinate occurred for samples 2.5 mm thick, which was significantly different from the other samples (P < 0.05). It was concluded that different composite thicknesses do not present similarity of color and have an influence on the final result of esthetic restorations.