Enhancing the Bandwidth and Energy Production of Piezoelectric Energy Harvester Using Novel Multimode Bent Branched Beam Design for Human Motion Application.

In recent years, harvesting energy from ubiquitous ultralow-frequency vibration sources, such as biomechanical motions using piezoelectric materials to power wearable devices and wireless sensors (e.g., personalized assistive tools for monitoring human locomotion and physiological signals), has drawn considerable interest from the renewable energy research community. Conventional linear piezoelectric energy harvesters (PEHs) generally consist of a cantilever beam with a piezoelectric patch and a proof mass, and they are often inefficient in such practical applications due to their narrow operating bandwidth and low voltage generation. Multimodal harvesters with multiple resonances appear to be a viable solution, but most of the previously proposed designs are unsuitable for ultralow-frequency vibration. This study investigated a novel multimode design, which included a bent branched beam harvester (BBBH) to enhance PEHs' bandwidth output voltage and output power for ultralow-frequency applications. The study was conducted using finite element method (FEM) analysis to optimize the geometrical design of the BBBH on the basis of the targeted frequency spectrum of human motion. The selected design was then experimentally studied using a mechanical shaker and human motion as excitation sources. The performance was also compared to the previously proposed V-shaped bent beam harvester (VBH) and conventional cantilever beam harvester (CBH) designs. The results prove that the proposed BBBH could harness considerably higher output voltages and power with lower idle time. Its operating bandwidth was also remarkably widened as it achieved three close resonances in the ultralow-frequency range. It was concluded that the proposed BBBH outperformed the conventional counterparts when used to harvest energy from ultralow-frequency sources, such as human motion.

Linear Segmented Arc-Shaped Piezoelectric Branch Beam Energy Harvester for Ultra-Low Frequency Vibrations.

Piezoelectric energy harvesting systems have been drawing the attention of the research community over recent years due to their potential for recharging/replacing batteries embedded in low-power-consuming smart electronic devices and wireless sensor networks. However, conventional linear piezoelectric energy harvesters (PEH) are often not a viable solution in such advanced practices, as they suffer from a narrow operating bandwidth, having a single resonance peak present in the frequency spectrum and very low voltage generation, which limits their ability to function as a standalone energy harvester. Generally, the most common PEH is the conventional cantilever beam harvester (CBH) attached with a piezoelectric patch and a proof mass. This study investigated a novel multimode harvester design named the arc-shaped branch beam harvester (ASBBH), which combined the concepts of the curved beam and branch beam to improve the energy-harvesting capability of PEH in ultra-low-frequency applications, in particular, human motion. The key objectives of the study were to broaden the operating bandwidth and enhance the harvester's effectiveness in terms of voltage and power generation. The ASBBH was first studied using the finite element method (FEM) to understand the operating bandwidth of the harvester. Then, the ASBBH was experimentally assessed using a mechanical shaker and real-life human motion as excitation sources. It was found that ASBBH achieved six natural frequencies within the ultra-low frequency range (<10 Hz), in comparison with only one natural frequency achieved by CBH within the same frequency range. The proposed design significantly broadened the operating bandwidth, favouring ultra-low-frequency-based human motion applications. In addition, the proposed harvester achieved an average output power of 427 µW at its first resonance frequency under 0.5 g acceleration. The overall results of the study demonstrated that the ASBBH design can achieve a broader operating bandwidth and significantly higher effectiveness, in comparison with CBH.

Branch spiral beam harvester for uni-directional ultra-low frequency excitations.

In recent years, there has been a growing interest in piezoelectric energy harvesting systems, particularly for their potential to recharge or replace batteries in energy-efficient electronic devices and wireless sensor networks. Nonetheless, the conventional linear piezoelectric energy harvesters (PEH) face limitations in ultra-low frequency vibrations (1-10 Hz) due to their narrow operating bandwidth and higher resonance frequencies. To address this, researchers explored compact shaped geometries, with spiral PEH being one such design to lower resonance frequencies by reducing structural stiffness. While trying to achieve this lower resonance frequency, spiral designs overlooked that they were spreading the stress across the structure. This was a significant drawback because it reduced the structure's ability to stress the piezoelectric transducer. The issue remains unaddressed, limiting the power generation of spiral beam harvesters. Furthermore, spiral structures also fail to broaden the operating bandwidth, posing additional constraints on their effectiveness. This study introduces a novel solution - the "branch spiral beam harvester," combining the benefits of both spiral and branch beam designs. The integration of the branch beam concept into the spiral structure aimed to broaden the effective frequency range and establish a concentrated stress area for the placement of the piezoelectric transducer. Finite Element Analysis (FEA) was employed to assess operating bandwidth and stress distribution, while experimental studies evaluated voltage and power generation. Once the workability was confirmed, a statistical optimisation method was introduced to tailor the harvester for specific frequencies in the ultra-low frequency range. Results indicated that the branch spiral beam harvester exhibits a wider operating bandwidth with six natural frequencies in the ultra-low frequency range. It harnessed significantly higher output voltages and power compared to conventional linear PEH. This innovation presents a promising advancement in piezoelectric energy harvesting, offering improved performance without the need for proof masses or additional accessories.