Lithium isotope tracing in silicon-based electrodes using solid-state MAS NMR: a powerful comprehensive tool for the characterization of lithium batteries.

The introduction of lithiated components with different 7Li/6Li isotopic ratios, also called isotopic tracing, can give access to better understanding of lithium transport and lithiation processes in lithium-ion batteries. In this work, we propose a simple methodology based on high-resolution solid-state NMR for the determination of the 7Li/6Li ratio in silicon electrodes following different strategies of isotopic tracing. The 6Li and 7Li MAS NMR experiments allow obtaining resolved spectra whose spectral components can be assigned to different moieties of the materials. In order to measure the ratio of the 6Li/7Li NMR integrals, a silicon electrode with a natural 7Li/6Li isotope abundance was used as a reference. This calibration can then be used to determine the 7Li/6Li ratio of any similar samples. This method was applied to study the phenomena occurring at the interface between a silicon electrode and a labeled electrolyte, which is an essential step for isotopic tracing experiments in systems after the formation of the solid electrolyte interphase (SEI). Beyond the isotopic exchanges between the SEI and the electrolyte already observed in the literature, our results show that isotopic exchanges also involve Li-Si alloys in the electrode bulk. Within a 52-hour contact, the electrolyte labeling disappeared: isotopic concentrations of the electrolyte and electrode become practically homogenized. However, at the electrode level, different silicides are characterized by rather different isotopic enrichment. In the present work, ToF SIMS and liquid state NMR were also used to cross-check and discuss the solid-state NMR method we have proposed.

Failure mechanisms of nano-silicon anodes upon cycling: an electrode porosity evolution model.

With a specific capacity of 3600 mA h g(-1), silicon is a promising anode active material for Li-ion batteries (LIBs). However, because of the huge volume changes undergone by Si particles upon (de)alloying with lithium, Si electrodes suffer from rapid capacity fading. A deep understanding of the associated failure mechanisms is necessary to improve these electrochemical performances. To reach this goal, we investigate here nano-Si based electrodes by several characterization techniques. Thanks to all these techniques, many aspects, such as the behaviour of the active material or the solid electrolyte interphase (SEI) and the lithiation mechanisms, are studied upon cycling. A clear picture of the failure mechanisms of nano-Si based electrodes is provided. In particular, by combining Hg analyses, SEM observations of electrode cross-sections, and EIS measurements, we follow the evolution of the porosity within the electrode. For the first time, our results clearly show a real dynamic of the pore size distribution: the first cycles lead to the formation of a micrometric porosity which is not present initially. During the following cycles, these large pores are progressively filled up with SEI products which form continuously at the Si particle surface. Thus, from the 50th cycle, Li(+) ion diffusion is dramatically hindered leading to a strongly heterogeneous lithiation of the electrode and a rapid capacity fading.

Lift-Out Specimen Preparation and Multiscale Correlative Investigation of Li-Ion Battery Electrodes Using Focused Ion Beam-Secondary Ion Mass Spectrometry Platforms.

Advanced characterization is paramount to understanding battery cycling and degradation in greater detail. Herein, we present a novel methodology of battery electrode analysis, employing focused ion beam (FIB) secondary-ion mass spectrometry platforms coupled with a specific lift-out specimen preparation, allowing us to optimize analysis and prevent air contamination. Correlative microscopy, combining electron microscopy and chemical imaging of a liquid electrolyte Li-ion battery electrode, is performed over the entire electrode thickness down to subparticle domains. We observed a distinctive remnant lithiation among interparticles of the anode at the discharge state. Furthermore, chemical mapping reveals the nanometric architecture of advanced composite active materials with a lateral resolution of 16 nm and the presence of a solid electrolyte interface on the particle boundaries. We highlight the methodological advantages of studying interfaces and the ability to conduct high-performance chemical and morphological correlative analyses of battery materials and comment on their potential use in other fields.

Study of Immersion of LiNi0.5Mn0.3Co0.2O2 Material in Water for Aqueous Processing of Positive Electrode for Li-Ion Batteries.

The understanding of the phenomena occurring during immersion of LiNi0.5Mn0.3Co0.2O2 (NMC) in water is helpful to devise new strategies toward the implementation of aqueous processing of this high-capacity cathode material. Immersion of NMC powder in water leads to both structural modification of the particles surface as observed by high-resolution scanning transmission electron microscopy and the formation of lithium-based compounds over the surface (LiOH, Li2CO3) in greater amount than after long-time exposure to ambient air, as confirmed by pH titration and 7Li MAS NMR analysis. The surface compounds adversely affect the electrochemical performance and are notably responsible for the alkaline pH of the aqueous slurry, which causes corrosion of the aluminum collector during coating of the electrode. The corrosion is avoided by adding phosphoric acid to the slurry as it lowers the pH, and it also enhances the cycling stability of the water-based electrodes due to the phosphate compounds formed at the particles surface, as evidenced by X-ray photoelectron spectroscopy analysis.

Multiscale Multiphase Lithiation and Delithiation Mechanisms in a Composite Electrode Unraveled by Simultaneous Operando Small-Angle and Wide-Angle X-Ray Scattering.

The (de)lithiation process and resulting atomic and nanoscale morphological changes of an a-Si/c-FeSi2/graphite composite negative electrode are investigated within a Li-ion full cell at several current rates (C-rates) and after prolonged cycling by simultaneous operando synchrotron wide-angle and small-angle X-ray scattering (WAXS and SAXS). WAXS allows the probing of the local crystalline structure. In particular, the observation of the graphite (de)lithiation process, revealed by the LixC6 Bragg reflections, enables access to the respective capacities of both graphite and active silicon. Simultaneously and independently, information on the silicon state of (de)lithiation and nanoscale morphology (1 to 60 nm) is obtained through SAXS. During lithiation, the SAXS intensity in the region corresponding to characteristic distances within the a-Si/c-FeSi2 domains increases. The combination of the SAXS/WAXS measurements over the course of several charge/discharge cycles, in pristine and aged electrodes, provides a complete picture of the C-rate-dependent sequential (de)lithiation mechanism of the a-Si/c-FeSi2/graphite anode. Our results indicate that, within the composite electrode, the active silicon volume does not increase linearly with lithium insertion and point toward the important role of the electrode morphology to accommodate the nanoscale silicon expansion, an effect that remains beneficial after cell aging and most probably explains the excellent performance of the composite material.

One-step synthesis of Si@C nanoparticles by laser pyrolysis: high-capacity anode material for lithium-ion batteries.

Carbon-covered silicon nanoparticles (Si@C) were synthesized for the first time by a one-step continuous process in a novel two stages laser pyrolysis reactor. Crystallized silicon cores formed in a first stage were covered in the second stage by a continuous shell mainly consisting in low organized sp(2) carbon. At the Si/C interface silicon carbide is absent. Moreover, the presence of silicon oxide is reduced compared to materials synthesized in several steps, allowing the use of such material as promising anode material in lithium-ion batteries (LIB). Auger Electron Spectroscopy (AES) analysis of the samples at both SiKLL and SiLVV edges proved the uniformity of the carbon coating. Cyclic voltammetry was used to compare the stability of Si and Si@C active materials. In half-cell configuration, Si@C exhibits a high and stable capacity of 2400 mAh g(-1) at C/10 and up to 500 mAh g(-1) over 500 cycles at 2C. The retention of the capacity is attributed to the protective effect of the carbon shell, which avoids direct contact between the silicon surface and the electrolyte.