AFM-IR: Technology and Applications in Nanoscale Infrared Spectroscopy and Chemical Imaging.

Atomic force microscopy-based infrared spectroscopy (AFM-IR) is a rapidly emerging technique that provides chemical analysis and compositional mapping with spatial resolution far below conventional optical diffraction limits. AFM-IR works by using the tip of an AFM probe to locally detect thermal expansion in a sample resulting from absorption of infrared radiation. AFM-IR thus can provide the spatial resolution of AFM in combination with the chemical analysis and compositional imaging capabilities of infrared spectroscopy. This article briefly reviews the development and underlying technology of AFM-IR, including recent advances, and then surveys a wide range of applications and investigations using AFM-IR. AFM-IR applications that will be discussed include those in polymers, life sciences, photonics, solar cells, semiconductors, pharmaceuticals, and cultural heritage. In the Supporting Information , the authors provide a theoretical section that reviews the physics underlying the AFM-IR measurement and detection mechanisms.

How to unravel the chemical structure and component localization of individual drug-loaded polymeric nanoparticles by using tapping AFM-IR.

AFM-IR is a photothermal technique that combines AFM and infrared (IR) spectroscopy to unambiguously identify the chemical composition of a sample with tens of nanometer spatial resolution. So far, it has been successfully used in contact mode in a variety of applications. However, the contact mode is unsuitable for soft or loosely adhesive samples such as polymeric nanoparticles (NPs) of less than 200 nm of wide interest for biomedical applications. We describe here the theoretical basis of the innovative tapping AFMIR mode that can address novel challenges in imaging and chemical mapping. The new method enables gaining information not only on NP morphology and composition, but also reveals drug location and core-shell structures. Whereas up to now the locations of NP components could only be hypothesized, tapping AFM-IR allows accurately visualizing both the location of the NPs' shells and that of the incorporated drug, pipemidic acid. The preferential accumulation of the drug in the NPs' top layers was proved, despite its low concentration (<1 wt%). These studies pave the way towards the use of tapping AFM-IR as a powerful tool to control the quality of NP formulations based on individual NP detection and component quantification.

Micromechanical contact stiffness devices and application for calibrating contact resonance atomic force microscopy.

This paper reports the design, fabrication, and characterization of micromechanical devices that can present an engineered contact stiffness to an atomic force microscope (AFM) cantilever tip. These devices allow the contact stiffness between the AFM tip and a substrate to be easily and accurately measured, and can be used to calibrate the cantilever for subsequent mechanical property measurements. The contact stiffness devices are rigid copper disks of diameters 2-18 µm integrated onto a soft silicone substrate. Analytical modeling and finite element simulations predict the elastic response of the devices. Measurements of tip-sample interactions during quasi-static force measurements compare well with modeling simulation, confirming the expected elastic response of the devices, which are shown to have contact stiffness 32-156 N m-1. To demonstrate one application, we use the disk sample to calibrate three resonant modes of a U-shaped AFM cantilever actuated via Lorentz force, at approximately 220, 450, and 1200 kHz. We then use the calibrated cantilever to determine the contact stiffness and elastic modulus of three polymer samples at these modes. The overall approach allows cantilever calibration without prior knowledge of the cantilever geometry or its resonance modes, and could be broadly applied to both static and dynamic measurements that require AFM calibration against a known contact stiffness.

Multifunctional atomic force microscope cantilevers with Lorentz force actuation and self-heating capability.

This paper reports the development of microcantilevers capable of self-heating and Lorentz-force actuation, and demonstrates applications to thermal topography imaging. Electrical current passing through a U-shaped cantilever in the presence of a magnetic field induces a Lorentz force on the cantilever free end, resulting in cantilever actuation. This same current flowing through a resistive heater induces a controllable temperature increase. We present cantilevers designed for large actuation forces for a given cantilever temperature increase. We analyze the designs of two new cantilevers, along with a legacy cantilever design. The cantilevers are designed to have a spring constant of about 1.5 N m(-1), a resonant frequency near 100 kHz, and self-heating capability with temperature controllable over the range 25-600 °C. Compared to previous reports on self-heating cantilevers, the Lorentz-thermal cantilevers generate up to seven times as much Lorentz force and two times as much oscillation amplitude. When used for thermal topography imaging, the Lorentz-thermal cantilevers can measure topography with a vertical resolution of 0.2 nm.

Widefield Super-Resolution Infrared Spectroscopy and Imaging of Autofluorescent Biological Materials and Photosynthetic Microorganisms Using Fluorescence Detected Photothermal Infrared (FL-PTIR).

We have demonstrated high-speed, super-resolution infrared (IR) spectroscopy and chemical imaging of autofluorescent biomaterials and organisms using camera-based widefield photothermal detection that takes advantage of temperature-dependent modulations of autofluorescent emission. A variety of biological materials and photosynthetic organisms exhibit strong autofluorescence emission under ultraviolet excitation and the autofluorescent emission has a very strong temperature dependence, of order 1%/K. Illuminating a sample with pulses of IR light from a wavelength-tunable laser source causes periodic localized sample temperature increases that result in a corresponding transient decrease in autofluorescent emission. A low-cost light-emitting diode-based fluorescence excitation source was used in combination with a conventional fluorescence microscopy camera to detect localized variations in autofluorescent emission over a wide area as an indicator of localized IR absorption. IR absorption image stacks were acquired over a range of IR wavelengths, including the fingerprint spectral range, enabling extraction of localized IR absorption spectra. We have applied widefield fluorescence detected photothermal IR (FL-PTIR) to an analysis of autofluorescent biological materials including collagen, leaf tissue, and photosynthetic organisms including diatoms and green microalgae cells. We have also demonstrated the FL-PTIR on live microalgae in water, demonstrating the potential for label-free dynamic chemical imaging of autofluorescent cells.

Lorentz force actuation of a heated atomic force microscope cantilever.

We report Lorentz force-induced actuation of a silicon microcantilever having an integrated resistive heater. Oscillating current through the cantilever interacts with the magnetic field around a NdFeB permanent magnet and induces a Lorentz force that deflects the cantilever. The same current induces cantilever heating. With AC currents as low as 0.2 mA, the cantilever can be oscillated as much as 80 nm at resonance with a DC temperature rise of less than 5 °C. By comparison, the AC temperature variation leads to a thermomechanical oscillation that is about 1000 times smaller than the Lorentz deflection at the cantilever resonance. The cantilever position in the nonuniform magnetic field affects the Lorentz force-induced deflection, with the magnetic field parallel to the cantilever having the largest effect on cantilever actuation. We demonstrate how the cantilever actuation can be used for imaging, and for measuring the local material softening temperature by sensing the contact resonance shift.

Monitoring TriAcylGlycerols Accumulation by Atomic Force Microscopy Based Infrared Spectroscopy in Streptomyces Species for Biodiesel Applications.

An atomic force microscope coupled with a tunable infrared laser source (AFM-IR) was used to measure the size and map the distribution of oil inclusions inside of microorganism without staining or other special sample preparation. The microorganism under study is Streptomyces, a soil bacterium that possesses the capability, under some specific nutritional conditions, to store its carbon source into TriAcylGlycerols, a potential direct source of biodiesel.

Nanometer-scale infrared spectroscopy of heterogeneous polymer nanostructures fabricated by tip-based nanofabrication.

There is a significant need for chemical identification and chemical imaging of nanofabricated structures and devices, especially for multiple materials integrated at the nanometer scale. Here we present nanofabrication, chemical identification, and nanometer-scale chemical imaging of polymer nanostructures with better than 100 nm spatial resolution. Polymer nanostructures of polyethylene, polystyrene, and poly(3-dodecylthiophene-2,5-diyl) were fabricated by tip-based nanofabrication. Nanometer-scale infrared measurements using atomic force microscopy infrared spectroscopy (AFM-IR) obtained quantitative chemical spectra of these nanostructures. We show chemical imaging of intersecting patterns of nanometer-scale polymer lines of different chemical compositions. The results indicate that for closely packed heterogeneous nanostructures, the spatial resolution of AFM-IR is not limited by nanometer-scale thermal diffusion, but is instead limited by the cantilever sensitivity and the signal-to-noise ratio of the AFM-IR system.

AFM-IR: combining atomic force microscopy and infrared spectroscopy for nanoscale chemical characterization.

Polymer and life science applications of a technique that combines atomic force microscopy (AFM) and infrared (IR) spectroscopy to obtain nanoscale IR spectra and images are reviewed. The AFM-IR spectra generated from this technique contain the same information with respect to molecular structure as conventional IR spectroscopy measurements, allowing significant leverage of existing expertise in IR spectroscopy. The AFM-IR technique can be used to acquire IR absorption spectra and absorption images with spatial resolution on the 50 to 100 nm scale, versus the scale of many micrometers or more for conventional IR spectroscopy. In the life sciences, experiments have demonstrated the capacity to perform chemical spectroscopy at the sub-cellular level. Specifically, the AFM-IR technique provides a label-free method for mapping IR-absorbing species in biological materials. On the polymer side, AFM-IR was used to map the IR absorption properties of polymer blends, multilayer films, thin films for active devices such as organic photovoltaics, microdomains in a semicrystalline polyhydroxyalkanoate copolymer, as well as model pharmaceutical blend systems. The ability to obtain spatially resolved IR spectra as well as high-resolution chemical images collected at specific IR wavenumbers was demonstrated. Complementary measurements mapping variations in sample stiffness were also obtained by tracking changes in the cantilever contact resonance frequency. Finally, it was shown that by taking advantage of the ability to arbitrarily control the polarization direction of the IR excitation laser, it is possible to obtain important information regarding molecular orientation in electrospun nanofibers.