Beyond the Surface: A Methodological Exploration of Enzyme Impact along the Cellulose Fiber Cross-Section.

Despite the wide range of analytical tools available for the characterization of cellulose, the in-depth characterization of inhomogeneous, layered cellulose fiber structures remains a challenge. When treating fibers or spinning man-made fibers, the question always arises as to whether the changes in the fiber structure affect only the surface or the entire fiber. Here, we developed an analysis tool based on the sequential limited dissolution of cellulose fiber layers. The method can reveal potential differences in fiber properties along the cross-sectional profile of natural or man-made cellulose fibers. In this analytical approach, carbonyl groups are labeled with a carbonyl selective fluorescence label (CCOA), after which thin fiber layers are sequentially dissolved with the solvent system DMAc/LiCl (9% w/v) and analyzed with size exclusion chromatography coupled with light scattering and fluorescence detection. The analysis of these fractions allowed for the recording of the changes in the chemical structure across the layers, resulting in a detailed cross-sectional profile of the different functionalities and molecular weight distributions. The method was optimized and tested in practice with LPMO (lytic polysaccharide monooxygenase)-treated cotton fibers, where it revealed the depth of fiber modification by the enzyme.

Cellulases adsorb reversibly on biomass lignin.

Adsorption of cellulases onto lignin is considered a major factor in retarding enzymatic cellulose degradation of lignocellulosic biomass. However, the adsorption mechanisms and kinetics are not well understood for individual types of cellulases. This study examines the binding affinity, kinetics of adsorption, and competition of four monocomponent cellulases of Trichoderma reesei during adsorption onto lignin. TrCel7A, TrCel6A, TrCel7B, and TrCel5A were radiolabeled for adsorption experiments on lignin-rich residues (LRRs) isolated from hydrothermally pretreated spruce (L-HPS) and wheat straw (L-HPWS), respectively. On the basis of adsorption isotherms fitted to the Langmuir model, the ranking of binding affinities was TrCel5A > TrCel6A > TrCel7B > TrCel7A on both types of LRRs. The enzymes had a higher affinity to the L-HPS than to the L-HPWS. Adsorption experiments with dilution after 1 and 24 hr and kinetic modeling were performed to quantify any irreversible binding over time. Models with reversible binding parameters fitted well and can explain the results obtained. The adsorption constants obtained from the reversible models agreed with the fitted Langmuir isotherms and suggested that reversible adsorption-desorption existed at equilibrium. Competitive binding experiments showed that individual types of cellulases competed for binding sites on the lignin and the adsorption data fitted the Langmuir adsorption model. Overall, the data strongly indicate that the adsorption of cellulases onto lignin is reversible and the findings have implications for the development of more efficient cellulose degrading enzymes.

Lignin Films from Spruce, Eucalyptus, and Wheat Straw Studied with Electroacoustic and Optical Sensors: Effect of Composition and Electrostatic Screening on Enzyme Binding.

Lignins were isolated from spruce, wheat straw, and eucalyptus by using the milled wood lignin (MWL) method. Functional groups and compositional analyses were assessed via 2D NMR and 31P NMR to realize their effect on enzyme binding. Films of the lignins were fabricated and ellipsometry, atomic force microscopy, and water contact angle measurements were used for their characterization and to reveal the changes upon enzyme adsorption. Moreover, lignin thin films were deposited on quartz crystal microgravimetry (QCM) and surface plasmon (SPR) resonance sensors and used to gain further insights into the lignin-cellulase interactions. For this purpose, a commercial multicomponent enzyme system and a monocomponent Trichoderma reesei exoglucanase (CBH-I) were considered. Strong enzyme adsorption was observed on the various lignins but compared to the multicomponent cellulases, CBH-I displayed lower surface affinity and higher binding reversibility. This resolved prevalent questions related to the affinity of this enzyme with lignin. Remarkably, a strong correlation between enzyme binding and the syringyl/guaiacyl (S/G) ratio was found for the lignins, which presented a similar hydroxyl group content (31P NMR): higher protein affinity was determined on isolated spruce lignin (99% G units), while the lowest adsorption occurred on isolated eucalyptus lignin (70% S units). The effect of electrostatic interactions in enzyme adsorption was investigated by SPR, which clearly indicated that the screening of charges allowed more extensive protein adsorption. Overall, this work furthers our understanding of lignin-cellulase interactions relevant to biomass that has been subjected to no or little pretreatment and highlights the widely contrasting effects of the nature of lignin, which gives guidance to improve lignocellulosic saccharification and related processes.

Cellulose hydrolysis and binding with Trichoderma reesei Cel5A and Cel7A and their core domains in ionic liquid solutions.

Ionic liquids (ILs) dissolve lignocellulosic biomass and have a high potential as pretreatment prior to total enzymatic hydrolysis. ILs are, however, known to inactivate cellulases. In this article, enzymatic hydrolysis of microcrystalline cellulose (MCC) and enzyme binding onto the cellulosic substrate were studied in the presence of cellulose-dissolving ILs. Two different ILs, 1,3-dimethylimidazolium dimethylphosphate ([DMIM]DMP) and 1-ethyl-3-methylimidazolium acetate ([EMIM]AcO), and two monocomponent cellulases, Trichoderma reesei cellobiohydrolase Cel7A and endoglucanase Cel5A, were used in the study. The role and IL sensitivity of the carbohydrate-binding module (CBM) were studied by performing hydrolysis and binding experiments with both the intact cellulases, and their respective core domains (CDs). Based on hydrolysis yields and substrate binding experiments for the intact enzymes and their CDs in the presence of ILs, the function of the CBM appeared to be very IL sensitive. Binding data suggested that the CBM was more important for the substrate binding of endoglucanase Cel5A than for the binding of cellobiohydrolase Cel7A. The CD of Cel7A was able to bind well to cellulose even without a CBM, whereas Cel5A CD had very low binding affinity. Hydrolysis also occurred with Cel5A CD even if this protein had very low binding affinity in all the studied matrices. Binding and hydrolysis were less affected by the studied ILs for Cel7A than for Cel5A. To our knowledge, this is the first systematic study of IL effects on cellulase substrate binding.

Carbohydrate-binding modules of fungal cellulases: occurrence in nature, function, and relevance in industrial biomass conversion.

In this review, the present knowledge on the occurrence of cellulases, with a special emphasis on the presence of carbohydrate-binding modules (CBMs) in various fungal strains, has been summarized. The importance of efficient fungal cellulases is growing due to their potential uses in biorefinery processes where lignocellulosic biomasses are converted to platform sugars and further to biofuels and chemicals. Most secreted cellulases studied in detail have a bimodular structure containing an active core domain attached to a CBM. CBMs are traditionally been considered as essential parts in cellulases, especially in cellobiohydrolases. However, presently available genome data indicate that many cellulases lack the binding domains in cellulose-degrading organisms. Recent data also demonstrate that CBMs are not necessary for the action of cellulases and they solely increase the concentration of enzymes on the substrate surfaces. On the other hand, in practical industrial processes where high substrate concentrations with low amounts of water are employed, the enzymes have been shown to act equally efficiently with and without CBM. Furthermore, available kinetic data show that enzymes without CBMs can desorb more readily from the often lignaceous substrates, that is, they are not stuck on the substrates and are thus available for new actions. In this review, the available data on the natural habitats of different wood-degrading organisms (with emphasis on the amount of water present during wood degradation) and occurrence of cellulose-binding domains in their genome have been assessed in order to identify evolutionary advantages for the development of CBM-less cellulases in nature.

Oxidation of cellulose fibers using LPMOs with varying allomorphic substrate preferences, oxidative regioselectivities, and domain structures.

Lytic polysaccharide monooxygenases (LPMOs) are excellent candidates for enzymatic functionalization of natural polysaccharides, such as cellulose or chitin, and are gaining relevance in the search for renewable biomaterials. Here, we assessed the cellulose fiber modification potential and catalytic performance of eleven cellulose-active fungal AA9-type LPMOs, including C1-, C4-, and C1/C4-oxidizing LPMOs with and without CBM1 carbohydrate-binding modules, on cellulosic substrates with different degrees of crystallinity and polymer chain arrangement, namely, Cellulose I, Cellulose II, and amorphous cellulose. The potential of LPMOs for cellulose fiber modification varied among the LPMOs and depended primarily on operational stability and substrate binding, and, to some extent, also on regioselectivity and domain structure. While all tested LPMOs were active on natural Cellulose I-type fibers, activity on the Cellulose II allomorph was almost exclusively detected for LPMOs containing a CBM1 and LPMOs with activity on soluble hemicelluloses and cello-oligosaccharides, for example NcAA9C from Neurospora crassa. The single-domain variant of NcAA9C oxidized the cellulose fibers to a higher extent than its CBM-containing natural variant and released less soluble products, indicating a more dispersed oxidation pattern without a CBM. Our findings reveal great functional variation among cellulose-active LPMOs, laying the groundwork for further LPMO-based cellulose engineering.

The impact of the carbohydrate-binding module on how a lytic polysaccharide monooxygenase modifies cellulose fibers.

BACKGROUND: In recent years, lytic polysaccharide monooxygenases (LPMOs) that oxidatively cleave cellulose have gained increasing attention in cellulose fiber modification. LPMOs are relatively small copper-dependent redox enzymes that occur as single domain proteins but may also contain an appended carbohydrate-binding module (CBM). Previous studies have indicated that the CBM "immobilizes" the LPMO on the substrate and thus leads to more localized oxidation of the fiber surface. Still, our understanding of how LPMOs and their CBMs modify cellulose fibers remains limited. RESULTS: Here, we studied the impact of the CBM on the fiber-modifying properties of NcAA9C, a two-domain family AA9 LPMO from Neurospora crassa, using both biochemical methods as well as newly developed multistep fiber dissolution methods that allow mapping LPMO action across the fiber, from the fiber surface to the fiber core. The presence of the CBM in NcAA9C improved binding towards amorphous (PASC), natural (Cell I), and alkali-treated (Cell II) cellulose, and the CBM was essential for significant binding of the non-reduced LPMO to Cell I and Cell II. Substrate binding of the catalytic domain was promoted by reduction, allowing the truncated CBM-free NcAA9C to degrade Cell I and Cell II, albeit less efficiently and with more autocatalytic enzyme degradation compared to the full-length enzyme. The sequential dissolution analyses showed that cuts by the CBM-free enzyme are more evenly spread through the fiber compared to the CBM-containing full-length enzyme and showed that the truncated enzyme can penetrate deeper into the fiber, thus giving relatively more oxidation and cleavage in the fiber core. CONCLUSIONS: These results demonstrate the capability of LPMOs to modify cellulose fibers from surface to core and reveal how variation in enzyme modularity can be used to generate varying cellulose-based materials. While the implications of these findings for LPMO-based cellulose fiber engineering remain to be explored, it is clear that the presence of a CBM is an important determinant of the three-dimensional distribution of oxidation sites in the fiber.

A novel approach to analyze the impact of lytic polysaccharide monooxygenases (LPMOs) on cellulosic fibres.

Enzymatic treatment of cellulosic fibres is a green alternative to classical chemical modification. For many applications, mild procedures for cellulose alteration are sufficient, in which the fibre structure and, therefore, the mechanical performance of cellulosic fibres are preserved. Lytic polysaccharide monooxygenases (LPMOs) bear a great potential to become a green reagent for such targeted cellulose modifications. An obstacle for wide implementation of LPMOs in tailored cellulose chemistry is the lack of suitable techniques to precisely monitor the LPMO impact on the polymer. Soluble oxidized cello-oligomers can be quantified using chromatographic and mass-spectrometric techniques. A considerable portion of the oxidized sites, however, remain on the insoluble cellulose fibres, and their quantification is difficult. Here, we describe a method for the simultaneous quantification of oxidized sites on cellulose fibres and changes in their molar mass distribution after treatment with LPMOs. The method is based on quantitative, heterogeneous, carbonyl-selective labelling with a fluorescent label (CCOA) followed by cellulose dissolution and size-exclusion chromatography (SEC). Application of the method to reactions of seven different LPMOs with pure cellulose fibres revealed pronounced functional differences between the enzymes, showing that this CCOA/SEC/MALS method is a promising tool to better understand the catalytic action of LPMOs.

Preferential adsorption and activity of monocomponent cellulases on lignocellulose thin films with varying lignin content.

Understanding the enzymatic hydrolysis of cellulose and the influence of lignin in the process are critical for viable production of fuels and chemicals from lignocellulosic biomass. The interactions of monocomponent cellulases with cellulose and lignin substrates were investigated by using thin films supported on quartz crystal microgravimetry (QCM) resonators. Trichoderma reesei exoglucanase (CBH-I) and endoglucanase (EG-I) bound strongly to both cellulose and lignin but EG-I exhibited a distinctive higher affinity with lignin, causing a more extensive inhibition of the cellulolytic reactions. CBH-I was found to penetrate into the bulk of the cellulose substrate increasing the extent of hydrolysis and film deconstruction. In the absence of a cellulose binding domain (CBD) and a linker, the CBH-I core adsorbed slowly and was not able to penetrate into the film. Conversely to CBH-I, EG-I exhibited activity only on the surface of the lignocellulose substrate even when containing a CBD and a linker. Interestingly, EG-I displayed a clearly different interaction profile as a function of contact time registered by QCM.

Inhibitory effect of lignin on the hydrolysis of xylan by thermophilic and thermolabile GH11 xylanases.

BACKGROUND: Enzymatic hydrolysis of lignocellulosic biomass into platform sugars can be enhanced by the addition of accessory enzymes, such as xylanases. Lignin from steam pretreated biomasses is known to inhibit enzymes by non-productively binding enzymes and limiting access to cellulose. The effect of enzymatically isolated lignin on the hydrolysis of xylan by four glycoside hydrolase (GH) family 11 xylanases was studied. Two xylanases from the mesophilic Trichoderma reesei, TrXyn1, TrXyn2, and two forms of a thermostable metagenomic xylanase Xyl40 were compared. RESULTS: Lignin isolated from steam pretreated spruce decreased the hydrolysis yields of xylan for all the xylanases at 40 and 50 °C. At elevated hydrolysis temperature of 50 °C, the least thermostable xylanase TrXyn1 was most inhibited by lignin and the most thermostable xylanase, the catalytic domain (CD) of Xyl40, was least inhibited by lignin. Enzyme activity and binding to lignin were studied after incubation of the xylanases with lignin for up to 24 h at 40 °C. All the studied xylanases bound to lignin, but the thermostable xylanases retained 22-39% of activity on the lignin surface for 24 h, whereas the mesophilic T. reesei xylanases become inactive. Removing of N-glycans from the catalytic domain of Xyl40 increased lignin inhibition in hydrolysis of xylan when compared to the glycosylated form. By comparing the 3D structures of these xylanases, features contributing to the increased thermal stability of Xyl40 were identified. CONCLUSIONS: High thermal stability of xylanases Xyl40 and Xyl40-CD enabled the enzymes to remain partially active on the lignin surface. N-glycosylation of the catalytic domain of Xyl40 increased the lignin tolerance of the enzyme. Thermostability of Xyl40 was most likely contributed by a disulphide bond and salt bridge in the N-terminal and α-helix regions.

Inhibition of enzymatic hydrolysis by residual lignins from softwood--study of enzyme binding and inactivation on lignin-rich surface.

Lignin-derived inhibition is a major obstacle restricting the enzymatic hydrolysis of cell wall polysaccharides especially with softwood lignocellulosics. Enzyme adsorption on lignin is suggested to contribute to the inhibitory effect of lignin. The interaction of cellulases with softwood lignin was studied in the present work with commercial Trichoderma reesei cellulases (Celluclast) and lignin-rich residues isolated from steam pretreated softwood (SPS) by enzymatic and acid hydrolysis. Both lignin preparations inhibited the hydrolysis of microcrystalline cellulose (Avicel) and adsorbed the major cellulases present in the commercial cellulase mixture. The adsorption phenomenon was studied at low temperature (4°C) and at the typical hydrolysis temperature (45°C) by following activities of free and lignin-bound enzymes. Severe inactivation of the lignin-bound enzymes was observed at 45°C, however at 4°C the enzymes retained well their activity. Furthermore, SDS-PAGE analysis of the lignin-bound enzymes indicated that very strong interactions form between the residue and the enzymes at 45°C, because the enzymes were not released from the residue in the electrophoresis. These results suggest that heat-induced denaturation may take place on the surface of softwood lignin at the hydrolysis temperature.

Effect of hydrothermal pretreatment severity on lignin inhibition in enzymatic hydrolysis.

Hydrothermal pretreatment is commonly used for enhancing enzymatic hydrolysis of lignocellulosics. Spruce and wheat straw were pretreated with increasing severity and lignin characteristics were analysed. The effect of enzymatically isolated lignin on the hydrolysis of Avicel and the adsorption of a cellobiohydrolase onto lignin was measured. Non-pretreated lignins had only a minor effect on Avicel hydrolysis. The structural changes in lignin accompanying hydrothermal pretreatment were associated with increased binding and inactivation of the cellulase on the lignin surface. The inhibitory effect was more pronounced in spruce than in wheat straw lignin. However, similar pretreatment severities caused similar levels of inhibition in Avicel hydrolysis for both biomass sources. The combined severity factor of the pretreatment correlated well with the inhibitory effect of lignin.

Lignin-derived inhibition of monocomponent cellulases and a xylanase in the hydrolysis of lignocellulosics.

Non-productive enzyme binding onto lignin is the major inhibitory mechanism, which reduces hydrolysis rates and yields and prevents efficient enzyme recycling in the hydrolysis of lignocellulosics. The detailed mechanisms of binding are still poorly understood. Enzyme-lignin interactions were investigated by comparing the structural properties and binding behaviour of fungal monocomponent enzymes, cellobiohydrolases TrCel7A and TrCel6A, endoglucanases TrCel7B and TrCel5A, a xylanase TrXyn11 and a ß-glucosidase AnCel3A, onto lignins isolated from steam pretreated spruce and wheat straw. The enzymes exhibited decreasing affinity onto lignin model films in the following order: TrCel7B>TrCel6A>TrCel5A>AnCel3A>TrCel7A>TrXyn11. As analysed in Avicel hydrolysis, TrCel6A and TrCel7B were most inhibited by lignin isolated from pretreated spruce. This could be partially explained by adsorption of the enzyme onto the lignin surface. Enzyme properties, such as enzyme surface charge, thermal stability or surface hydrophobicity could not alone explain the adsorption behaviour.

Impact of steam explosion on the wheat straw lignin structure studied by solution-state nuclear magnetic resonance and density functional methods.

Chemical changes of lignin induced by the steam explosion (SE) process were elucidated. Wheat straw was studied as the raw material, and lignins were isolated by the enzymatic mild acidolysis lignin (EMAL) procedure before and after the SE treatment for analyses mainly by two-dimensional (2D) [heteronuclear single-quantum coherence (HSQC) and heteronuclear multiple-bond correlation (HMBC)] and (31)P nuclear magnetic resonance (NMR). The ß-O-4 structures were found to be homolytically cleaved, followed by recoupling to ß-5 linkages. The homolytic cleavage/recoupling reactions were also studied by computational methods, which verified their thermodynamic feasibility. The presence of the tricin bound to wheat straw lignin was confirmed, and it was shown to participate in lignin reactions during the SE treatment. The preferred homolytic ß-O-4 cleavage reaction was calculated to follow bond dissociation energies: G-O-G (guaiacyl) (69.7 kcal/mol) > G-O-S (syringyl) (68.4 kcal/mol) > G-O-T (tricin) (67.0 kcal/mol).

Effects of residual lignin and heteropolysaccharides on the bioconversion of softwood lignocellulose nanofibrils obtained by SO2-ethanol-water fractionation.

The amount of residual lignin and hemicelluloses in softwood fibers was systematically varied by SO2-ethanol-water fractionation for integrated biorefinery with nanomaterial and biofuel production. On the basis of their low energy demand in mechanical processing, the fibers were deconstructed to lignocellulose nanofibrils (LCNF) and used as substrate for bioconversion. The effect of LCNF composition on saccharification via multicomponent enzymes was investigated at different loadings. LCNF digestibility was compared with the enzyme activity measured with a quartz crystal microbalance. LCNF hydrolysis rate gradually decreased with lignin and hemicellulose concentration, both of which limited enzyme accessibility. Enzyme inhibition resulted from non-productive binding of proteins onto lignin. Near complete LCNF hydrolysis was achieved, even at high lignin and hemicellulose content. Sugar yields for LCNF were higher than those for precursor SEW fibers, highlighting the benefits of high surface area in LCNF.

Inhibitory effect of lignin during cellulose bioconversion: the effect of lignin chemistry on non-productive enzyme adsorption.

The effect of lignin as an inhibitory biopolymer for the enzymatic hydrolysis of lignocellulosic biomass was studied; specially addressing the role of lignin in non-productive enzyme adsorption. Botanical origin and biomass pre-treatment give rise to differences in lignin structure and the effect of these differences on enzyme binding and inhibition were elucidated. Lignin was isolated from steam explosion (SE) pre-treated and non-treated spruce and wheat straw and used for the preparation of ultrathin films for enzyme binding studies. Binding of Trichoderma reesei Cel7A (CBHI) and the corresponding Cel7A-core, lacking the linker and the cellulose-binding domain, to the lignin films was monitored using a quartz crystal microbalance (QCM). SE pre-treatment altered the lignin structure, leading to increased enzyme adsorption. Thus, the positive effect of SE pre-treatment, opening the cell wall matrix to make polysaccharides more accessible, may be compromised by the structural changes of lignin that increase non-productive enzyme adsorption.

Effect of temperature on lignin-derived inhibition studied with three structurally different cellobiohydrolases.

Non-productive enzyme adsorption onto lignin inhibits enzymatic hydrolysis of lignocellulosic biomass. Three cellobiohydrolases, Trichoderma reesei Cel7A (TrCel7A) and two engineered fusion enzymes, with distinctive modular structures and temperature stabilities were employed to study the effect of temperature on inhibition arising from non-productive cellulase adsorption. The fusion enzymes, TeCel7A-CBM1 and TeCel7A-CBM3, were composed of a thermostable Talaromyces emersonii Cel7A (TeCel7A) catalytic domain fused to a carbohydrate-binding module (CBM) either from family 1 or from family 3. With all studied enzymes, increase in temperature was found to increase the inhibitory effect of supplemented lignin in the enzymatic hydrolysis of microcrystalline cellulose. However, for the different enzymes, lignin-derived inhibition emerged at different temperatures. Low binding onto lignin and thermostable structure were characteristic for the most lignin-tolerant enzyme, TeCel7A-CBM1, whereas TrCel7A was most susceptible to lignin especially at elevated temperature (55 °C).

Cellulase-lignin interactions-the role of carbohydrate-binding module and pH in non-productive binding.

Non-productive cellulase adsorption onto lignin is a major inhibitory mechanism preventing enzymatic hydrolysis of lignocellulosic feedstocks. Therefore, understanding of enzyme-lignin interactions is essential for the development of enzyme mixtures and processes for lignocellulose hydrolysis. We have studied cellulase-lignin interactions using model enzymes, Melanocarpus albomyces Cel45A endoglucanase (MaCel45A) and its fusions with native and mutated carbohydrate-binding modules (CBMs) from Trichoderma reesei Cel7A. Binding of MaCel45A to lignin was dependent on pH in the presence and absence of the CBM; at high pH, less enzyme bound to isolated lignins. Potentiometric titration of the lignin preparations showed that negatively charged groups were present in the lignin samples and that negative charge in the samples was increased with increasing pH. The results suggest that electrostatic interactions contributed to non-productive enzyme adsorption: Reduced enzyme binding at high pH was presumably due to repulsive electrostatic interactions between the enzymes and lignin. The CBM increased binding of MaCel45A to the isolated lignins only at high pH. Hydrophobic interactions are probably involved in CBM binding to lignin, because the same aromatic amino acids that are essential in CBM-cellulose interaction were also shown to contribute to lignin-binding.