Helical plating - a novel technique to increase stiffness in defect fractures.

Single-plate fixation bridging bone defects provokes nonunion and risks plate-fatigue failure due to under- dimensioned implants. Adding a helical plate to bridge the fracture increases stiffness and balances load sharing. This study compares the stiffness and plate surface strain of different constructs in a transverse contact and gap femoral shaft fracture model. Eight groups of six synthetic femora each were formed: intact femora; intact femora with lateral locking plate; contact and gap transverse shaft osteotomies each with lateral locking plate, lateral locking plate and helical locking plate, and long proximal femoral nail. Constructs underwent non-destructive quasi-static axial and torsional loading. Plate surface strain evaluation was performed under 200 N axial loading. Constructs with both lateral and helical plates demonstrated similar axial and torsional stiffness- independent of the contact or gap situations - being significantly higher compared to lateral plating (p < 0.01). Torsional stiffness of the constructs, with both lateral and helical plates in the gap situation, was significantly higher compared to this situation stabilised by a nail (p < 0.01). Plate surface strain dropped from 0.3 % in the gap situation with a lateral plate to < 0.1 % in this situation with both a lateral and a helical plate. Additional helical plating increases axial and torsional construct stiffness in synthetic bone and seems to provide well-balanced load sharing. Its use should be considered in very demanding situations for gap or defect fractures, where single-plate osteosynthesis provides inadequate stiffness for fracture healing and induces nonunion.

[Special reduction instruments]. / Spezielle Repositionsinstrumente.

Special and specialized instruments help perform reduction more effectively and in a tissue-preserving manner. In addition to other articles, the application and advantages of the following instruments are presented: colinear reduction forceps, cerclage, cerclage passer, distal radius reduction clamp, modular external fixator, extension table, distraction frame, joystick, manipulators, distractor and assistance of reduction with elastic nails.

How to Choose between the Implant Materials Steel and Titanium in Orthopedic Trauma Surgery: Part 2 - Biological Aspects.

BIOLOGICAL ASPECTS OF STEEL AND TITANIUM AS IMPLANT MATERIAL IN ORTHOPEDIC TRAUMA SURGERY The following case from the ICUC database, where a titanium plate was implanted into a flourishing infection, represents the clinical experience leading to preferring titanium over steel. (Fig. 1) (6). Current opinions regarding biological aspects of implant function. The "street" opinions regarding the biological aspects of the use of steel versus titanium as a surgical trauma implant material differ widely. Statements of opinion leaders range from "I do not see any difference in the biological behavior between steel and titanium in clinical application" to "I successfully use titanium implants in infected areas in a situation where steel would act as foreign body "sustaining" infection." Furthermore, some comments imply that clinical proof for the superiority of titanium in human application is lacking. The following tries to clarify the issues addressing the different aspects more through a practical clinical approach than a purely scientific one, this includes simplifications. Today's overall biocompatibility of implant materials is acceptable but: As the vast majority of secondary surgeries are elective procedures this allows the selection of implant materials with optimal infection resistance. The different biological reactions of stainless steel and titanium are important for this segment of clinical pathologies. Biological tole - rance (18) depends on the toxicity and on the amount of soluble implant material released. Release, diffusion and washout through blood circulation determine the local concentration of the corrosion products. Alloying components of steel, especially nickel and chromium, are less than optimal in respect to tissue tolerance and allergenicity. Titanium as a pure metal provides excellent biological tolerance (3, 4, 16). Better strength was obtained by titanium alloys like TiAl6V4. The latter found limited application as surgical implants. It contains Vanadium (9). Today's high strength titanium alloys contain well tolerated alloying components1 like Zr, Nb, Mo and Ta (ISO 5832-14) (7, 15). The corrosion rate of surgical implants is kept low by the passive layer formed when immerged in body fluids (13, 14). The passive layer may be locally destroyed, for instance, by mechanical fretting or by local corrosion conditions like in pitting; it is renewed by an electrochemical corrosion process which releases alloying components like Ni and Cr (Fig. 2) (10). The amount of soluble component may vary markedly depending on the local electrochemical conditions (see below).

The Potential of the ICUC® Documentation Concept to Improve Trauma Surgery.

Conventional documentation of surgical procedures using only pre- and postoperative X-ray images and possibly a few intra-operative pictures does not allow secondary analysis of the technical performance in detail. In particular, the quality of the handling of tissues and surgical tools cannot be judged «post hoc¼, i.e. after the end of the surgical procedure. The invasiveness of the surgical act cannot yet be quantified. Surrogate invasiveness indices have therefore been developed. Furthermore, conventional documentation does not allow evaluation of the proper use of the C-arm both technically and with regard to fluoroscopy time. Documentation that follows the ICUC® documentation concept includes all fluoroscopy shots and images covering all key portions of the entire surgical procedure by multiple still images or videos. In certain cases, such documentation can help to explain post-operative courses that might be difficult to understand based only on X-rays and written operation reports. Finally, the data included in ICUC® documentation are a valuable source for knowledge extraction. In addition, time saving is conceivable if operation reports can include images of the key stages of the procedure with a few additional comments dictated during the surgery. Key words: trauma surgery, ICUC® documentation concept.

Evolution of AO Fracture Treatment Part 1: the Internal Fixator.

Surgical fracture treatment has undergone an extensive evolution in the past decades. In the early days achieving solid healing in anatomically reduced position was the primary and nearly exclusive goal of fracture treatment. Since mainly Lambotte, Danis and Müller in Europe the focus of surgical fracture treatment shifted to achieving early recovery of the function of the injured limb with safe healing. Considering the shortcomings of the early fracture treatment helps understanding the evolution of surgical fracture treatment. The evolution of the biomechanical and biological principles of AO plate fixation are discussed as a model.

How to Choose between the Implant Materials Steel and Titanium in Orthopedic Trauma Surgery: Part 1 - Mechanical Aspects.

When choosing between metal implants of different materials the surgeon mainly needs to balance the pros and cons of steel and titanium. Economic constraints often do not permit both to be kept in stock and it is necessary to decide beforehand which to choose. The arguments for the use of the "preferred metal" vary. The present paper elucidates the practical aspects based on the complex scientific background that has identified the differences between the two metals in their mechanical, electrochemical, biological and application behavior. The data presented here are intended to help the surgeon when he is confronted with different and often complex clinical situations and problems. The following is an overview of different aspects to help with selection of the proper material for the clinical application. The first part concerns mechanical aspects the second part the biological aspects. Both aspects are discussed with the practical application in mind. Nonmetallic implant materials have seen an increasing interest in the recent past. Plastic materials needed improvement to achieve good strength and avoid creep with loss of e.g. compression and minimizing leakage of chemicals.

Balancing Success and Risk in Orthopedic Trauma Surgery: The Ridge-Walking between Sound Accepting "Good" and Risky Striving for "Better".

Immediate post-operative rating of surgical performance can be a valuable source of learning when trying to analyze the reasons for the difference between "work as planned" and "work as done". There are many reasons for the difference, but they can only be found if complete documentation of the surgical steps allows retrospective scrutiny. Documentation like ICUC1 provides this opportunity for scrutiny and may allow better understanding of some unexpected post-operative evolutions.

Biomechanical and biological aspects of defect treatment in fractures using helical plates.

The clinical case of figure 1 through figure 11 shows a series of impressive failures of plate fixation. The plates were repeatedly applied bridging a comminuted bone segment in a heavy patient. The biomechanical analysis elaborates why this happened and proposes an unconventional procedure to prevent this failure with a minimally invasive procedure. A plate bridging an open gap or a defect in a long bone diaphysis is exposed to full functional load. According to clinical observations such plate application often fails even without external load such as weight bearing. The plate risks to break through fatigue when exposed during a long time to cyclic loading. This type of failure has been observed even with broad plates as well in femoral as in tibiae. The first option to avoid such failure consists in protecting the plate by installing load sharing between plate and either bone or an additional implant. This reduces the load carried by the plate to a safe level. Load sharing with bone may be installed at surgery by establishing solid mechanical bridge between the two main fragments of the fractured bone. The optimal load sharing relies on a solid compressed contact between the main fragments. It can be established because the bone is able to take a large load which results in optimal protection of the plate. In the case of an extended comminuted bone segment it may be very difficult, traumatizing and inefficient to reconstruct the bone. In the present case it was impossible to establish load sharing through the bone. The second option protecting the plate is provided by callus bridging of the gap or defect. The formation of a solid callus bridge takes time but the fatigue failure of the plate also takes time. Therefore, the callus bridge may prevent a late fatigue failure. The surgeon may select one of several options: - Replacing the lack of bone support using a second plate which immediately alleviates plate loading. The drawback of application of a second conventional plate is the extent of surgical trauma at the critical site of healing. - Shingling and/or applying an autologous cancellous bone graft: This procedure provides initially no relevant load sharing but will do so after a couple of weeks. The mechanical coupling of the comparably soft graft and the main fracture fragments presents little problems. Applying a cortical bone graft: Such a graft does provide initial only small load sharing and does a less good job inducing callus than a cancellous graft. Furthermore, the coupling by callus between a somewhat rigid bone graft and the mobile main fracture fragments requires a solid maintained contact. If the cortical graft is fixed using implants with small contact area to the graft such as screws or cerclage loops, the local stress may be critical and the graft may break. When the cortical graft is fixed with cerclage wires the procedure must take into account the limited strength of the individual cerclage. Therefore multiple and well-spaced cerclages are required and may lead to success especially if an intramedullary component of the implant contributes to protection (6). The degree of unloading depends apparently on the stiffness of the material of the protecting splint. Though, more important is the effect of the dimensions of the splint. While titanium as a material is about 50% less stiff than steel, the thickness of the implant changes the stiffness with the third power. That is doubling the thickness results in eightfold increased stiffness. When considering the unloading by application of a second plate the leverage of the second plate plays an important role. The larger the distance between the axis of bending and the second implant the larger the protecting effect. The helical plate (2, 3, 7) as introduced by A.A.D. Fernandez offers biological and mechanical advantages. It can be applied without touching the fracture site maintaining the critical biology intact and provides mechanically efficient unloading. Its application is fairly simple: The helical plate is modified conventional long and small plate that is twisted between its ends about 90 degrees. The twist is applied using "bending irons" (4, 5, 8) whereby the force required is small and the exact degree of twist is not critical. Therefore the twist is applicable operating bending irons by hand. Assuming a situation where a plate bridging a defect or non-union has failed the broken plate is replaced by a similar implant: At the distal end of the bone fracture and opposite to the surgical approach a small incision allows to slide in the helical plate in such a way that proximally the plate ends on the same side of the limb as the replaced plate. Ideally the two plate ends meet and the application of the helical plate does not ask for an additional surgical exposure at this location. Otherwise a small minimally invasive exposure is required. The helical plate is then fixed to the main bone fragments using a couple of locked screws. The following case demonstrates the use and efficiency of the helical plate saving a situation where multiple attempts using conventional plates had failed. The successful final treatment of this case was performed by A. A. D. Fernandez.

Quantification of surgical trauma: comparison of conventional and minimally invasive surgical techniques for pertrochanteric fracture surgery based on markers of inflammation (interleukins).

BACKGROUND: Fixation of pertrochanteric fracture is undoubtedly an additional trauma after the fracture itself. In elderly patients, it might have an important impact on the whole organism. In the literature we find various techniques to perform this type of surgery. Up to now, there are no parameters validated for quantification of the invasiveness of a surgical procedure; it is therefore still not demonstrated that any method is less invasive than any other. In an effort to find a way to quantify the invasiveness of a surgical procedure, inflammatory markers were collected in patients undergoing fixation of trochanteric fracture with gliding hip screw [dynamic hip screw (DHS)] using either a conventional (DHS conv) or minimally invasive (DHS MIO) technique. METHOD: Two groups of patients were investigated prospectively; 36 of them were treated with conventional DHS technique and 32 with minimally invasive technique. Mean age was 84.7 ± 7.20 and 82.78 ± 7.71 years, respectively. Fracture type was classified according to the AO classification. Interleukin (IL)-6, IL-10, IL-8, and tumor necrosis factor (TNF)-α were measured 1 h before and 1 h after surgery. Student's t test, chi-square test, and multivariate logistic regression were used for statistical analysis. RESULTS: Preoperative levels of interleukins showed no significant differences between the two groups. In contrast, the postoperative blood level of IL-6 in patients operated with DHS conv technique (78.41 ± 67.04 pg/ml) was on average higher than in patients operated by DHS MIO technique (39.02 ± 37.36 pg/ml), the mean difference being 39.39 pg/ml [95 % confidence interval (CI) 12.65-66.13 pg/ml; p = 0.0045]. Multivariate logistic regression (backward method with limit of significance 0.05) confirmed that patients operated by conventional technique were significantly more likely to have increased IL-6 after surgery than those operated by MIO technique. IL-8 was measured in only 36 patients (20 for DHS conv, 16 for DHS MIO). No significant differences were found between the two groups; however, there was a drastic decrease postoperatively (p < 0.0001) regardless of the type of surgery performed. IL-10 and TNF-α were tested in all subjects, but did not show significant differences between the two groups. Average length of incision was significantly different (4.61 cm, 95 % CI 3.50-5.71 cm; p < 0.001) between the two groups, being 11.65 ± 2.64 cm for DHS conv and 7.05 ± 1.77 cm for DHS MIO. Similarly, average units of red blood cells (RBCs) transfused [performed for hemoglobin (Hb) <9 g/dl and/or hematocrit (HCT) <27 %] was higher (2.22 ± 0.99) in the DHS conv group compared with the DHS MIO group (1.09 ± 1.20), with average difference of 1.13 (95 % CI 0.59-1.66; p < 0.001). CONCLUSIONS: This attempt to quantify the invasiveness of internal fixation for trochanteric fracture comparing two techniques (DHS conv versus DHS MIO) based on inflammatory markers (IL-6) has given encouraging results. Measurement of systemic inflammatory response to local tissue damage caused by osteosynthesis using IL-6 as marker seems to confirm the lower invasiveness of MIO techniques. These results for trauma cases seem in line with those published for hip prosthesis. Ongoing further studies analyzing the effect of nailing will confirm or invalidate these preliminary results.

Impact of a multifunctional image-guided therapy suite on emergency multiple trauma care.

BACKGROUND: The multifunctional image-guided therapy suite (MIGTS), a combined diagnostic and operating theatre, is currently the subject of considerable interest. This study investigated the effect of instituting a MIGTS on the emergency treatment of multiply injured patients. METHODS: This prospective controlled intervention study (MIGTS versus conventional treatment) included consecutive multiply injured trauma patients (Injury Severity Score of 16 or more) admitted between February 2003 and April 2005 to a university hospital. Main outcome measures were time to computed tomography (CT) and number of in-hospital transfers. RESULTS: A total of 168 patients were enrolled, 87 in the MIGTS and 81 in the control group. On average, CT was started at least 13 min sooner in the MIGTS group (P < 0.001), and these patients underwent fewer within-hospital transfers before arrival in the intensive care unit (median 2 versus 4 for controls; odds ratio -2.92, P < 0.001). Team members indicated increased satisfaction with the quality of the MIGTS procedure over the course of the study (P = 0.009). Thirty-day mortality rate (17 per cent for MIGTS versus 22 per cent for controls; P = 0.420) and long-term outcome did not differ between the two groups. CONCLUSION: Implementation of a MIGTS in the emergency treatment of multiple trauma significantly accelerated the procedure and reduced the number of in-hospital transports. REGISTRATION NUMBER: NCT0072213 (http://www.clinicaltrials.gov).

Positioning accuracy in a registration-free CT-based navigation system.

In order to maintain overall navigation accuracy established by a calibration procedure in our CT-based registration-free navigation system, the CT scanner has to repeatedly generate identical volume images of a target at the same coordinates. We tested the positioning accuracy of the prototype of an advanced workplace for image-guided surgery (AWIGS) which features an operating table capable of direct patient transfer into a CT scanner. Volume images (N = 154) of a specialized phantom were analysed for translational shifting after various table translations. Variables included added weight and phantom position on the table. The navigation system's calibration accuracy was determined (bias 2.1 mm, precision +/- 0.7 mm, N = 12). In repeated use, a bias of 3.0 mm and a precision of +/- 0.9 mm (N = 10) were maintainable. Instances of translational image shifting were related to the table-to-CT scanner docking mechanism. A distance scaling error when altering the table's height was detected. Initial prototype problems visible in our study causing systematic errors were resolved by repeated system calibrations between interventions. We conclude that the accuracy achieved is sufficient for a wide range of clinical applications in surgery and interventional radiology.

[Interdisciplinary emergency room management of trauma patients from the standpoint of coworkers]. / Interdisziplinäres Schockraum-Management unfallchirurgischer Patienten aus der Sicht der Mitarbeitenden.

INTRODUCTION: The purpose of this study was to examine whether staff questionnaire evaluation is useful for quality control in the emergency room (ER) setting. METHODS: Consecutive anonymous questionnaires (Likert scale 1-5) were filled out by the involved medical staff in all ER trauma cases in a university hospital from July 2002 to December 2003 (analysis of variance, P<0.05). RESULTS: In 171 ER cases, 844 staff members responded. Main criticisms concerned time management or satisfaction with personal ER training (Likert <4). Consultants rated the quality of their training significantly higher than younger doctors, two thirds of consultants vs one third of residents having passed an Advanced Trauma and Life Support course (P<0.001). Depending on responders' professional specialties and whether the situation concerned multiple trauma (Injury Severity Score >15), a significant systematic difference resulted. CONCLUSION: Our standardized staff questionnaire evaluation was revealed to be a discriminative instrument for quality management of trauma cases in the ER. To confirm these findings, correlation with clinical outcome data and further validation of the method are needed.

A whole-body registration-free navigation system for image-guided surgery and interventional radiology.

RATIONALE AND OBJECTIVES: To develop and test an image-guided navigation system in which the base of reference is taken from the imaging modality, here, a helical CT scanner. METHODS: An optical digitizer together with a calibration device is used to measure the transformation matrix between the digitizer reference system and a CT reference system. During intervention, it tracks radiological and surgical tools with tool references. A specific software visually integrates the current tool position with the corresponding image information. In vitro accuracy tests were performed. RESULTS: With helical CT, freehand positioning accuracy was 1.9 +/- 1.1 mm (mean +/- SD) in vitro (n = 718). CONCLUSIONS: The navigation system developed by the authors appears to be feasible for radiological interventions as well as for minimally invasive surgery. It is not limited to a certain procedure, can be used in every region of the body, and is functional after imaging. Intraprocedural scans can be integrated immediately.

Fractures of the distal end of the radius treated by internal fixation and early function. A preliminary report of 20 cases.

Fractures of the distal end of the radius should be treated on the same principles as other fractures involving joints. Displaced articular fractures require open reduction to allow anatomical reconstruction of both the radiocarpal and the radio-ulnar joints. For extra-articular fractures with severe comminution and shortening this enables the radial length to be re-established achieving radio-ulnar congruency. Stable internal fixation can be achieved with two 2.0 AO titanium plates placed on each of the 'lateral' and the 'intermediate' columns of the wrist at an angle of 50 degrees to 70 degrees. This gives good stability despite the tiny dimensions of the plates, and allows early function. We report a series of 20 fractures treated by this method of internal fixation with satisfactory results in all.

Fractures of the distal radius treated by internal fixation and early function. A prospective study of 73 consecutive patients.

Stable fixation of fractures of the distal radius can be achieved by using two 2.0 mm titanium plates placed on the radial and intermediate columns angled 50 degrees to 70 degrees apart. We describe our results with this method in a prospective series of 74 fractures (58 severely comminuted) in 73 consecutive patients. Early postoperative mobilisation was possible in all except four wrists. All of the 73 patients, except two with other injuries, returned to work and daily activities with no limitations. The anatomical results were excellent or good in 72 patients and fair in one. Our discussion includes details of important technical considerations based on an analysis of the specific complications which were seen early in the series.

Arthroscopic findings in acute fractures of the ankle.

We have evaluated prospectively the arthroscopic findings in acute fractures of the ankle in 288 consecutive patients (148 men and 140 women) with a mean age of 45.6 years. According to the AO-Danis-Weber classification there were 14 type-A fractures, 198 type B and 76 type C. Lesions of the cartilage were found in 228 ankles (79.2%), more often on the talus (69.4%) than on the distal tibia (45.8%), the fibula (45.1%), or the medial malleolus (41.3%). There were more lesions in men than in women and in general they were more severe in men (p < 0.05). They also tended to be worse in patients under 30 years and in those over 60 years of age. The frequency and severity of the lesions increased from type-B to type-C fractures (p < 0.05). Within each type of fracture the lesions increased from subgroups 1 to 3 (p < 0.05). The anterior tibiofibular ligament was injured with increased frequency from type-B.1 to type-C3 fractures (p < 0.05), but it was not torn in all cases. While lateral ligamentous injuries were seen more often in type-B than in type-C fractures (p < 0.05), no difference was noted in the frequency of deltoid ligamentous lesions. Our findings show that arthroscopy is useful in identifying associated intra-articular lesions in acute fractures of the ankle.

Operative treatment of distal humeral fractures in the elderly.

We treated 49 patients at an average age of 80 years (75 to 90) with distal mostly intraarticular humeral fractures by open reduction. There were 8 class A, 13 class B and 28 class C fractures on Müller's classification. The patients were reviewed at a postoperative average of 18 months. The patients' assessment of the result was very good in 31%, good in 49%, fair in 15% and poor in 5%. The flexion-extension range was very good in 41%, good in 44% and fair in 15%. The incidence of implant failure, pseudarthrosis of the olecranon osteotomy and ulnar nerve lesion was no higher in these elderly patients than in younger patients. Old age is not a contraindication to open reduction and internal fixation; it is important to restore full function.

Bridging bone gaps with the Ilizarov technique. Biologic principles.

For the treatment of bone gaps of less than 4 cm, cancellous autografting remains the treatment of choice. But for gaps exceeding 4 cm, the distraction osteogenesis is a viable option. The following conditions should be satisfied: (1) patient selection; (2) stable fixation; (3) osteotomy by corticotomy; (4) 7- to 14-day latency period before initiating distraction; and (5) a controlled rate and rhythm of distraction of 1 mm per day (0.25 mm, four times a day). This type of treatment leaves the pathologic focus alone, and bone healing occurs on the healthy bone. The quality of bone regenerate may be improved by a motorized unit and by better soft-tissue coverage using early grafts and flaps. Interface healing is probably improved by cancellous grafting and internal fixation after the transport period, thus decreasing the fixator time.