Blood flow analyses by intraoperative transit-time flow measurements of free flaps for head and neck reconstructions: A prospective single-center study.

BACKGROUND: The behavior of blood flow changes within free flaps following microvascular anastomosis is not well described in the literature. The aim of this study was to determine the immediate blood flow behavior of different free flaps as reference values for various clinical applications. METHODS: Intraoperative transit-time flow measurements were performed on patients receiving free flap transfer in the head and neck area comprising radial forearm flaps (RFF), peroneal artery perforator flaps (PAP), anterolateral thigh flaps (ALT), vastus lateralis flaps (VLF), parascapular flaps (PSF), latissimus dorsi flaps (LDF), fibula free flaps (FFF), deep circumflex iliac artery flaps (DCIA), and scapular flaps (SF). In accordance with a structured protocol, measurements took place at the pedicle directly before flap harvesting and at the recipient vessels 1 h after flap transfer. Heart rate, transplant weight, and other patient characteristics were recorded and analyzed. RESULTS: A total of 129 were enrolled, comprising 66 RFF, 8 ALT, 6 PAP, 11 VLF, 3 PSF, 2 LDF, 24 FFF, 7 DCIA, and 2 SF. In most of the transplant groups, arterial perfusion increased after anastomosis at the recipient site. The arterial pulsatility index developed indirectly proportionally to arterial blood flow, whereas venous blood drainage did not show any statistically significant changes. Muscle flaps had the highest arterial perfusion before flap transfer. Composite transplants with hard and soft tissue presented the greatest increase in arterial perfusion. The lowest arterial blood flow after anastomosis was measured in PAP and RFF. In contrast, RFF and PAP presented the highest arterial perfusion per 100 g transplant weight. CONCLUSIONS: Arterial perfusion changed, whereas venous blood flow did not show any statistically significant variations in any transplant group. Perfusion of free flaps does not only depend on the recipient vessel and the recipient bed, but also on flap-specific anatomy and physiology.

Structure-Activity Relationship for Di- up to Tetranuclear Macrocyclic Ruthenium Catalysts in Homogeneous Water Oxidation.

Two di- and tetranuclear Ru(bda) (bda: 2,2'-bipyridine-6,6'-dicarboxylate) macrocyclic complexes were synthesized and their catalytic activities in chemical and photochemical water oxidation investigated in a comparative manner to our previously reported trinuclear congener. Our studies have shown that the catalytic activities of this homologous series of multinuclear Ru(bda) macrocycles in homogeneous water oxidation are dependent on their size, exhibiting highest efficiencies for the largest tetranuclear catalyst. The turnover frequencies (TOFs) have increased from di- to tetranuclear macrocycles not only per catalyst molecule but more importantly also per Ru unit with TOF of 6 s-1 to 8.7 s-1 and 10.5 s-1 in chemical and 0.6 s-1 to 3.3 s-1 and 5.8 s-1 in photochemical water oxidation per Ru unit, respectively. Thus, for the first time, a clear structure-activity relationship could be established for this novel class of macrocyclic water oxidation catalysts.

NAM-help or burden? Intercultural evaluation of parental stress caused by nasoalveolar molding: a retrospective multi-center study.

OBJECTIVES: Nasoalveolar molding (NAM) was developed to facilitate easier treatment and better outcomes for cleft lip and palate (CLP) patients. The aim of this study was to investigate the parental burden and possible intercultural differences of this treatment modality, which is often argued to burden parents to an extraordinary amount. MATERIALS AND METHODS: Standardized questionnaires (available in English, Mandarin, and German) with 15 non-specific and 14 NAM-specific items to be retrospectively answered by Likert scales by parents of unilateral CLP patients with completed NAM treatment. RESULTS: The parents of 117 patients from two treatment centers in Taiwan and Germany were included. A very high level of overall satisfaction was found in both countries with significant intercultural differences in prenatal parent information, feeding problems, dealing with 3rd party's perception, and experienced personal effort. CONCLUSION: NAM is an effective treatment tool for children's CLP deformities and their caregivers in overcoming the feeling of helplessness. Intercultural differences may be due to infrastructural reasons, cultural attitudes and habits, or different public medical education. CLINICAL RELEVANCE: In addition to facilitating easier surgical treatment, NAM can be seen as a powerful coping strategy for parents dealing with a CLP deformity of their child and does not seem to burden them extraordinarily.

A prospective longitudinal study of postnatal dentoalveolar and palatal growth: The anatomical basis for CAD/CAM-assisted production of cleft-lip-palate feeding plates.

This study describes the dentoalveolar and palatal growth during the first months of life. Knowledge concerning this development is essential to avoid unwanted events such as mucosal ulcerations or restriction of growth when cleft-lip and palate (CLP) patients are treated. The results involve the generation of CAD/CAM CLP-feeding plates. Intraoral impressions from 32 healthy newborns were taken monthly for 5 months, supplemented by measurements of body weight, length, and occipital-frontal head circumference. The casts were digitalized, and two observers manually selected defined anatomical landmarks on virtual 3-D models. The distances between these landmarks were evaluted. Statistical analysis included an inter-rater agreement analysis and the determination of growth. In total, 213 casts were analyzed, with 65 models excluded because of inaccuracies in impression-taking or cast production. Overall longitudinal growth was 20.3%, whereas transversal growth reached a maximum of 21.1%. Vertical growth was 32.4% at the tuberal level. On the basis of these results, a semiautomated series of feeding plates allowing for monthly expansion could be generated. The acquired data serve as a useful reference for other pediatric and orthofacial investigations and treatments. One such application is the automated, fully virtual manufacture of CLP-feeding plates based on only one impression-taking. Our data reveal when caution is needed to prevent ulceration. The series of plates generated can minimize the time-consuming impression-taking and the production of further plaster models. The method of measurement is suitable for documentary purposes. Clin. Anat. 30:846-854, 2017. © 2017 Wiley Periodicals, Inc.

Author Correction: A semi-automated virtual workflow solution for the design and production of intraoral molding plates using additive manufacturing: the first clinical results of a pilot-study.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

Prenatal intrauterine maxillary development - An evaluation with three-dimensional ultrasound.

OBJECTIVES: The aim of this prospective study was to investigate normal fetal maxillary development with volume ultrasound during the prenatal phase, for a better estimation of maxillary growth processes. METHODS: Some 210 3D volumes were obtained in two measurement series from 38 healthy women (gestational age: 19+2 to 31+4 weeks) using a GE Voluson™ E10 ultrasound system. Maxillary length and width were determined in the axial and sagittal planes. Clearly defined, reproducible landmarks were used for measurements. The results were correlated with gestational age and compared with previously reported studies. RESULTS: Total maxillary length ranged from 10.30 to 24.75 mm, total maxillary width from 13.65 to 37.30 mm in an observation period during the second trimester, with high reproducibility for all landmarks. All evaluation results showed steep growth with exponential character. Length growth was determined to be more dominant than width growth. Intra-rater correlation was evaluated to be almost perfect (ICC (3) > 0.8). CONCLUSION: This study presents measurements of physiological fetal maxillary development. The defined landmarks proved to be representative for further investigations. This study serves as a baseline for a better understanding of fetal maxillary growth processes, and may be useful for standardising detection of malformations or intrauterine growth restrictions.

The absolute and relative effects of presurgical nasoalveolar moulding in bilateral cleft lip and palate patients compared with nasal growth in healthy newborns.

BACKGROUND: This study investigated the efficiency of nasoalveolar moulding (NAM) in patients presenting with bilateral cleft lip and palate (BCLP). It focused explicitly on nasal outcome and therefore made comparisons with healthy age-matched infants with normal nasal development. METHODS: Nasal impressions from 19 BCLP patients were analysed at the beginning and at the end of NAM treatment. In addition, nasal impressions from 32 healthy newborns were taken monthly for 4 months. The casts were digitalized and analysed, using defined anatomic landmarks, by two independent observers. Initial values were compared with outcome parameters at the end of NAM therapy and with the healthy cohort. RESULTS: NAM significantly elongated the columella in BCLP patients, with an increase of 106.5% versus 14.5% in healthy newborns. Nostril height showed significant expansion from 4.2 mm to 5.6 mm on the right side, and from 4.3 mm to 6.2 mm on the left side. CONCLUSION: NAM significantly elongated columella length and increased nostril height. The comparison with healthy newborns showed the effectiveness of early cartilage moulding. Detailed knowledge about absolute and relative early nasal growth was gained. However, despite highly effective NAM treatment in BCLP, nasal dimensions will not reach healthy proportions.

Evaluation of a portable low-budget three-dimensional stereophotogrammetry system for nasal analysis.

BACKGROUND: Three-dimensional (3D) photogrammetry has reached high standards and accuracy but is mainly conducted with stationary and expensive systems. The purpose of this study was to evaluate the accuracy of a low-budget portable system with special regard to the gracile and challenging nasal region. MATERIAL AND METHODS: 3D models of the perinasal area were acquired by impression-taking and the scanning of the generated plaster models (3Shape D500) or with a portable low-budget 3D stereophotogrammetry (FUEL3D® SCANIFY®) system. Four examiners analysed defined landmarks of the generated Standard Tessellation Language files with regard to accuracy and interobserver reliability by using 3dMDvultus™ software. A semi-automatic 3D best-fit analysis of both models was performed by using Geomagic® and the Root Mean Squared (RMS) errors were calculated. RESULTS: 41 volunteers were included, with 22 perinasal and perioral landmarks, 15 3D distances and eight 3D angles being analysed per data set. In a point-based analysis the mean spreads were partially smaller in the plaster model scans. Most measurements showed very high (>0.8) to excellent (>0.9) intraclass correlation coefficients, the lowest being found for columella length (0.686) and left nostril width (0.636). Overall, the mean RMS error between the superimposed surfaces was 0.89 ± 0.22 mm in the best-fit analysis. CONCLUSIONS: The corresponding software program was operator-friendly. The findings indicate that the analysed, affordable and portable system is a feasible solution for 3D image acquisition with comparable accuracy reported in the literature. Further studies will analyse the feasibility in neonates.

Stress Distribution Patterns within Viscero- and Neurocranium during Nasoalveolar Molding: a Finite Element Analysis.

BACKGROUND: The purpose of this study was to evaluate the stress distribution patterns within the viscero- and neurocranium of neonates during nasoalveolar molding. METHODS: Finite element models of 3 different healthy neonates at different times of life (date of birth, 4 weeks, and 3.5 months) were generated on the basis of computed tomography scans. A validated workflow, including segmentation, meshing, setting of boundary conditions, and implementation of a bone density-dependent material model, was carried out for each model. A small and a large unilateral alveolar and hard palatal cleft were virtually cut in each model. The stress distribution pattern in each model was then analyzed by using Ansys APDL. RESULTS: Convergence analysis validated the results. The virtual experiments at the date of birth showed a stress pattern above a previously defined threshold value of 30,000 Pa in the ipsilateral naso-orbital-complex, frontal sinus, and the anterior fossa of the base of the skull, with von Mises values > 35,000 Pa. Stress patterns at the age of 4 weeks and 3.5 months showed reduced von Mises values at < 15,000 Pa. CONCLUSIONS: Nasoalveolar molding therapy is a safe presurgical treatment modality without significant influence on the viscero- and neurocranium of neonates. Treatment, considering the stress distribution at the naso-orbital-complex and anterior fossa of the base of the skull, should begin in the second week of life, and treatment initiation of preterm infants should be adapted respectively.

Facilitating CAD/CAM nasoalveolar molding therapy with a novel click-in system for nasal stents ensuring a quick and user-friendly chairside nasal stent exchange.

Nasoalveolar molding (NAM) aims to improve nasal symmetry with a nasal stent in cleft lip and palate (CLP) patients. When plates have to be exchanged because of dentoalveolar growth or cleft reduction, the nasal stent has to be mounted onto a new plate. This procedure elongates visiting hours for patients and parents or requires second treatment sessions. This study introduces a quick-lock additive manufacturing solution for chairside nasal stent exchange called RapidNAM. A novel taping retention pin has been designed that enables nasal stent insertion. Patients with unilateral CLP were included in this study. Plaster models were digitalized and measured by two independent observers. Two methods of CAD/CAM-molding therapies were compared: (i) conventional adhesion of a nasal stent (CAD/CAM NAM); (ii) quick-lock system in which the nasal stent was transferred to another plate (RapidNAM). CAD/CAM NAM and its refinement RapidNAM significantly increased the cleft-side nasal height and tilted the nose towards symmetry. The quick-lock system minimizes wire adaptations, since the pre-existing stent can be reused. The new nasal stent development seems a feasible solution to minimize visiting hours but with clinically satisfactory results. This new nasal stent system combines traditional elements of NAM with CAD/CAM-technology.

A semi-automated virtual workflow solution for the design and production of intraoral molding plates using additive manufacturing: the first clinical results of a pilot-study.

Computer-aided design and computer-aided manufacturing (CAD/CAM) technology has been implemented in the treatment of cleft lip and palates (CLP) by several research groups. This pilot study presents a technique that combines intraoral molding with a semi-automated plate generation and 3D-printing. The clinical results of two intraoral molding approaches are compared. This is the first clinical investigation of semi-automated intraoral molding. Our study included newborns with unilateral CLP. Plaster models were digitalized and measured by two independent observers. Two methods of CAD/CAM-assisted intraoral molding were compared: (i) stepwise manual design of molding plates (conventional CAD/CAM-intraoral molding) and (ii) a semi-automated approach with an automated detection of alveolar ridges (called RapidNAM) assisted by a graphical user interface (GUI). Both approaches significantly narrowed the clefts and resulted in a harmonic alveolar crest alignment. The GUI was easy to use and generated intraoral molding devices within minutes. The presented design solution is an efficient technical refinement with good clinical results. The semi-automated plate generation with a feasible GUI is fast but allows individual adaptations. This promising technique might facilitate and foster the more widespread use of CAD/CAM-technology in intraoral molding therapy.

The possibilities of a portable low-budget three-dimensional stereophotogrammetry system in neonates: a prospective growth analysis and analysis of accuracy.

BACKGROUND: With the technical development, portable three-dimensional (3D) photogrammetry systems are becoming more en vogue because of cost-effectiveness and comparable accuracy to common stationary 3D systems. The purpose of the study was to evaluate the feasibility and accuracy of a low-budget portable system for 3D image acquisition with special regard to the gracile nasal region in neonates. Furthermore, the study aimed to establish a 3D data set of the first 180 days post partum. METHODS: Thirty-three healthy, full-term newborn were enrolled and 3D photographs were prospectively taken monthly with a portable low-budget 3D stereophotogrammetry system (FUEL3D® SCANIFY®) for six months. In the third month, age-matched and corresponding 3D models were acquired by taking an impression of the perinasal area. The resulting plaster models were scanned (3Shape D700, 3Shape® A/S, Denmark). Three examiners analyzed independently 21 defined landmarks of the generated Standard Tessellation Language files with regard to accuracy by using 3dMDvultus™ software. A semi-automatic 3D best-fit analysis of 3D photo and plaster models were performed by using Geomagic® and the Root Mean Squared (RMS) errors were calculated. RESULTS: Statistically significant changes of midfacial distances and angles with a focus on nasal growth during the first 180 days postpartum could be specified in absolute and relative dimensions. Best-fit analysis in the third month revealed a RMS error of 0.72 ± 0.22 mm with a mean standard deviation of 0.71 ± 0.21 mm. CONCLUSIONS: The analyzed portable 3D stereophotogrammetry system is a feasible methodology with good accuracy, even in newborn. A description of the growth as well as the establishment of a 3D data set was performed. Its implementation for basic documentation for example in cleft patients is possible and might reduce the need for impressions and facilitate the communications with parents and the interdisciplinary team.

Axiographic results of CAD/CAM-assisted microvascular, fibular free flap reconstruction of the mandible: A prospective study of 21 consecutive cases.

Virtual planning and guided reconstruction of the mandible following ablative surgery have become standard procedures in reconstructive surgery. Many advantages regarding operation time, morphology, bony fit, and consolidation have been described, but analyses of the functional outcome of virtually planned mandibular reconstructions are lacking. We prospectively analyzed 21 consecutive cases of mandibular reconstructions using CAD/CAM-assisted microvascular, fibular free flaps in operations between July 2014 and January 2016 at a single center. Axiographic measurements were performed preoperatively and at 10 days and 3 months postoperatively and were correlated with clinical findings. Uni- and multivariate regression analyses were performed to determine the association between possible predictor variables on functional outcomes. Overall, no statistical differences between the t1 and t3 measurements were seen in the analyzed variables. The univariate analysis showed a significant influence of indication and pre- and postoperative irradiation only on mouth opening (p = 0.018, p = 0.026, and p = 0.049). Timing, the number of osteotomies, and the incidence of wound healing disturbances had no significant influence on postoperative function (p = 0.753, p = 0.69 and p = 0.776). In particular, cases without malignancy or preoperative irradiation benefitted from the integration of the CAD/CAM technique and showed good functional outcomes.

Predictors of free flap loss in the head and neck region: A four-year retrospective study with 451 microvascular transplants at a single centre.

INTRODUCTION: Microvascular free flaps have become an essential part of reconstructive surgery following head and neck tumour ablation. The authors' aim was to investigate the influence of cardiovascular risk factors, preoperative irradiation, previous operations and metabolically active medication on free flap loss in order to predict patients at risk and to improve their therapy. MATERIALS AND METHODS: All patients who underwent reconstructive surgery with microvascular free flaps in the head and neck region between 2009 and 2013 were retrospectively analysed. Uni- and multivariate logistic regressions were performed to determine the association between possible predictor variables for free flap loss. RESULTS: We included 451 patients in our analysis. The overall free flap failure rate was 4.0%. Multivariate regression analysis revealed significantly increased risks of free flap failure depending on prior attempts at microvascular transplants (p < 0.001, OR = 14.21) and length of hospitalisation (p = 0.007, OR = 1.05). CONCLUSIONS: With consistently low rates of flap failure, microvascular reconstruction of defects in the head and neck region has proven to be highly reliable, even in patients with comorbidities. The expertise of the operating team seems to remain the main factor affecting flap success. The only discerned independent predictor was previously failed attempts at microvascular reconstruction.