Improving Charge Injection at Gold/Conjugated Polymer Contacts by Polymer Insulator-Assisted Annealing for Transistors.

The poor chemical miscibility between metal and organic materials usually leads to both structural and energetic mismatches at gold/organic interfaces, and thereby, high contact resistance of organic electronic devices. This study shows that the contact resistance of organic field-effect transistors is significantly reduced by one order of magnitude, by reforming the contact interface between gold electrodes and conjugated polymers upon a polymer insulator-assisted thermal annealing. Upon an optimized solution process, the conjugated polymer is homogenously distributed within the amorphous polymer insulator matrix with relatively low glass transition temperature, and thus, even a moderate annealing temperature can induce sufficient motion of conjugated polymer chains to simultaneously adjust the polymer orientation and improve the packing of gold atoms. Consequently, gold/conjugated polymer contact is reorganized after annealing, which improves both charge transport from bulk gold to interface and charge injection from gold into conjugated polymers. This method, with appropriate insulator matrix, is effective for improving the injection of both holes and electrons, and widely applicable for many unipolar and ambipolar conjugated polymers to optimize the device performance and simultaneously increase the optical transparency (over 80%). A frequency doubler and a phase modulator are demonstrated, respectively, using the ambipolar transistors with optimized charge injection properties.

A Combinatorial Study Investigating the Growth of Ultrasmall Embedded Silver Nanoparticles upon Thermal Annealing.

Ultrasmall nanoparticles (NPs) with a high active surface area are essential for optoelectronic and photovoltaic applications. However, the structural stability and sustainability of these ultrasmall NPs at higher temperatures remain a critical problem. Here, we have synthesized the nanocomposites (NCs) of Ag NPs inside the silica matrix using the atom beam co-sputtering technique. The post-deposition growth of the embedded Ag NPs is systematically investigated at a wide range of annealing temperatures (ATs). A novel, fast, and effective procedure, correlating the experimental (UV-vis absorption results) and theoretical (quantum mechanical modeling, QMM) results, is used to estimate the size of NPs. The QMM-based simulation, employed for this work, is found to be more accurate in reproducing the absorption spectra over the classical/modified Drude model, which fails to predict the expected shift in the LSPR for ultrasmall NPs. Unlike the classical Drude model, the QMM incorporates the intraband transition of the conduction band electrons to calculate the effective dielectric function of metallic NCs, which is the major contribution of LSPR shifts for ultrasmall NPs. In this framework, a direct comparison is made between experimentally and theoretically observed LSPR peak positions, and it is observed that the size of NPs grows from 3 to 18 nm as AT increases from room temperature to 900 °C. Further, in situ grazing-incidence small- & wide-angle X-ray scattering and transmission electron microscopy measurements are employed to comprehend the growth of Ag NPs and validate the UV + QMM results. We demonstrate that, unlike chemically grown NPs, the embedded Ag NPs ensure greater stability in size and remain in an ultrasmall regime up to 800 °C, and beyond this temperature, the size of NPs increases exponentially due to dominant Ostwald ripening. Finally, a three-stage mechanism is discussed to understand the process of nucleation and growth of the silica-embedded Ag NPs.

Structure Development of the Interphase between Drying Cellulose Materials Revealed by In Situ Grazing-Incidence Small-Angle X-ray Scattering.

The nano- to microscale structures at the interface between materials can define the macroscopic material properties. These structures are extremely difficult to investigate for complex material systems, such as cellulose-rich materials. The development of new model cellulose materials and measuring techniques has opened new possibilities to resolve this problem. We present a straightforward approach combining micro-focusing grazing-incidence small-angle X-ray scattering and atomic force microscopy (AFM) to investigate the structural rearrangements of cellulose/cellulose interfaces in situ during drying. Based on the results, we propose that molecular interdiffusion and structural rearrangement play a major role in the development of the properties of the cellulose/cellulose interphase; this model is representative of the development of the properties of joint/contact points between macroscopic cellulose fibers.

Percolation of rigid fractal carbon black aggregates.

We examine network formation and percolation of carbon black by means of Monte Carlo simulations and experiments. In the simulation, we model carbon black by rigid aggregates of impenetrable spheres, which we obtain by diffusion-limited aggregation. To determine the input parameters for the simulation, we experimentally characterize the micro-structure and size distribution of carbon black aggregates. We then simulate suspensions of aggregates and determine the percolation threshold as a function of the aggregate size distribution. We observe a quasi-universal relation between the percolation threshold and a weighted average radius of gyration of the aggregate ensemble. Higher order moments of the size distribution do not have an effect on the percolation threshold. We conclude further that the concentration of large carbon black aggregates has a stronger influence on the percolation threshold than the concentration of small aggregates. In the experiment, we disperse the carbon black in a polymer matrix and measure the conductivity of the composite. We successfully test the hypotheses drawn from simulation by comparing composites prepared with the same type of carbon black before and after ball milling, i.e., on changing only the distribution of aggregate sizes in the composites.

Flow fields control nanostructural organization in semiflexible networks.

Hydrodynamic alignment of proteinaceous or polymeric nanofibrillar building blocks can be utilized for subsequent assembly into intricate three-dimensional macrostructures. The non-equilibrium structure of flowing nanofibrils relies on a complex balance between the imposed flow-field, colloidal interactions and Brownian motion. The understanding of the impact of non-equilibrium dynamics is not only weak, but is also required for structural control. Investigation of underlying dynamics imposed by the flow requires in situ dynamic characterization and is limited by the time-resolution of existing characterization methods, specifically on the nanoscale. Here, we present and demonstrate a flow-stop technique, using polarized optical microscopy (POM) to quantify the anisotropic orientation and diffusivity of nanofibrils in shear and extensional flows. Microscopy results are combined with small-angle X-ray scattering (SAXS) measurements to estimate the orientation of nanofibrils in motion and simultaneous structural changes in a loose network. Diffusivity of polydisperse systems is observed to act on multiple timescales, which is interpreted as an effect of apparent fibril lengths that also include nanoscale entanglements. The origin of the fastest diffusivity is correlated to the strength of velocity gradients, independent of type of deformation (shear or extension). Fibrils in extensional flow results in highly anisotropic systems enhancing interfibrillar contacts, which is evident through a slowing down of diffusive timescales. Our results strongly emphasize the need for careful design of fluidic microsystems for assembling fibrillar building blocks into high-performance macrostructures relying on improved understanding of nanoscale physics.

Flow-assisted assembly of nanostructured protein microfibers.

Some of the most remarkable materials in nature are made from proteins. The properties of these materials are closely connected to the hierarchical assembly of the protein building blocks. In this perspective, amyloid-like protein nanofibrils (PNFs) have emerged as a promising foundation for the synthesis of novel bio-based materials for a variety of applications. Whereas recent advances have revealed the molecular structure of PNFs, the mechanisms associated with fibril-fibril interactions and their assembly into macroscale structures remain largely unexplored. Here, we show that whey PNFs can be assembled into microfibers using a flow-focusing approach and without the addition of plasticizers or cross-linkers. Microfocus small-angle X-ray scattering allows us to monitor the fibril orientation in the microchannel and compare the assembly processes of PNFs of distinct morphologies. We find that the strongest fiber is obtained with a sufficient balance between ordered nanostructure and fibril entanglement. The results provide insights in the behavior of protein nanostructures under laminar flow conditions and their assembly mechanism into hierarchical macroscopic structures.

Polymeric, Cost-Effective, Dopant-Free Hole Transport Materials for Efficient and Stable Perovskite Solar Cells.

Perovskite solar cells (PSCs) has skyrocketed in the past decade to an unprecedented level due to their outstanding photoelectric properties and facile processability. However, the utilization of expensive hole transport materials (HTMs) and the inevitable instability instigated by the deliquescent dopants represent major concerns hindering further commercialization. Here, a series of low-cost, conjugated polymers are designed and applied as dopant-free HTMs in PSCs, featuring tuned energy levels, good temperature and humidity resistivity, and excellent photoelectric properties. Further studies highlight the critical and multifaceted roles of the polymers with respect to facilitating charge separation, passivating the surface trap sites of perovskite materials, and guaranteeing long-term stability of the devices. A stabilized power conversion efficiency (PCE) of 20.3% and remarkably enhanced device longevity are achieved using the dopant-free polymer P3 with a low concentration of 5 mg/mL, qualifying the device as one of the best PSC systems constructed on the basis of dopant-free HTMs so far. In addition, the flexible PSCs based on P3 also exhibit a PCE of 16.2%. This work demonstrates a promising route toward commercially viable, stable, and efficient PSCs.

Ion-Specific Assembly of Strong, Tough, and Stiff Biofibers.

Designing engineering materials with high stiffness and high toughness is challenging as stiff materials tend to be brittle. Many biological materials realize this objective through multiscale (i.e., atomic- to macroscale) mechanisms that are extremely difficult to replicate in synthetic materials. Inspired from the architecture of such biological structures, we here present flow-assisted organization and assembly of renewable native cellulose nanofibrils (CNFs), which yields highly anisotropic biofibers characterized by a unique combination of high strength (1010 MPa), high toughness (62 MJ m-3 ) and high stiffness (57 GPa). We observed that properties of the fibers are primarily governed by specific ion characteristics such as hydration enthalpy and polarizability. A fundamental facet of this study is thus to elucidate the role of specific anion binding following the Hofmeister series on the mechanical properties of wet fibrillar networks, and link this to the differences in properties of dry nanostructured fibers. This knowledge is useful for rational design of nanomaterials and is critical for validation of specific ion effect theories. The bioinspired assembly demonstrated here is relevant example for designing high-performance materials with absolute structural control.

Effect of chain architecture on the swelling and thermal response of star-shaped thermo-responsive (poly(methoxy diethylene glycol acrylate)-block-polystyrene)3 block copolymer films.

The effect of chain architecture on the swelling and thermal response of thin films obtained from an amphiphilic three-arm star-shaped thermo-responsive block copolymer poly(methoxy diethylene glycol acrylate)-block-polystyrene ((PMDEGA-b-PS)3) is investigated by in situ neutron reflectivity (NR) measurements. The PMDEGA and PS blocks are micro-phase separated with randomly distributed PS nanodomains. The (PMDEGA-b-PS)3 films show a transition temperature (TT) at 33 °C in white light interferometry. The swelling capability of the (PMDEGA-b-PS)3 films in a D2O vapor atmosphere is better than that of films from linear PS-b-PMDEGA-b-PS triblock copolymers, which can be attributed to the hydrophilic end groups and limited size of the PS blocks in (PMDEGA-b-PS)3. However, the swelling kinetics of the as-prepared (PMDEGA-b-PS)3 films and the response of the swollen film to a temperature change above the TT are significantly slower than that in the PS-b-PMDEGA-b-PS films, which may be related to the conformation restriction by the star-shape. Unlike in the PS-b-PMDEGA-b-PS films, the amount of residual D2O in the collapsed (PMDEGA-b-PS)3 films depends on the final temperature. It decreases from (9.7 ± 0.3)% to (7.0 ± 0.3)% or (6.0 ± 0.3)% when the final temperatures are set to 35 °C, 45 °C and 50 °C, respectively. This temperature-dependent reduction of embedded D2O originates from the hindrance of chain conformation from the star-shaped chain architecture.

Manipulating the Assembly of Spray-Deposited Nanocolloids: In Situ Study and Monolayer Film Preparation.

Fabrication of nanoparticle arrays on a substrate is one of the most concerned aspects for manipulating assembly of nanoparticles and preparing functional nanocomposites. Here, we studied in situ the assembly kinetics of polystyrene nanocolloids by using grazing incidence small-angle X-ray scattering. The structure formation of the nanoparticle film is monitored during air-brush spraying, which provides a rapid and scalable preparation. By optimizing the substrate temperature, the dispersion of the nanocolloids can be tailored to prepare monolayer film. The success of the monolayer preparations is attributed to the fast solvent evaporation which inhibits the aggregation of the nanocolloids. The present study may open a new avenue for the manufacture-friendly preparation of well-dispersed nanoparticle thin films.

Anisotropic particles align perpendicular to the flow direction in narrow microchannels.

The flow orientation of anisotropic particles through narrow channels is of importance in many fields, ranging from the spinning and molding of fibers to the flow of cells and proteins through thin capillaries. It is commonly assumed that anisotropic particles align parallel to the flow direction. When flowing through narrowed channel sections, one expects the increased flow rate to improve the parallel alignment. Here, we show by microfocus synchrotron X-ray scattering and polarized optical microscopy that anisotropic colloidal particles align perpendicular to the flow direction after passing a narrow channel section. We find this to be a general behavior of anisotropic colloids, which is also observed for disk-like particles. This perpendicular particle alignment is stable, extending downstream throughout the remaining part of the channel. We show by microparticle image velocimetry that the particle reorientation in the expansion zone after a narrow channel section occurs in a region with considerable extensional flow. This extensional flow is promoted by shear thinning, a typical property of complex fluids. Our discovery has important consequences when considering the flow orientation of polymers, micelles, fibers, proteins, or cells through narrow channels, pipes, or capillary sections. An immediate consequence for the production of fibers is the necessity for realignment by extension in the flow direction. For fibrous proteins, reorientation and stable plug flow are likely mechanisms for protein coagulation.

Sorption of Water and Initial Stages of Swelling of Thin PNIPAM Films Using in Situ GISAXS Microfluidics.

The sorption of low-molecular penetrants by thin polymer films, as well as structural changes provoked therein, is of high relevance for many fields of application. Complex permeation, diffusion, swelling, and dissolution processes are often induced within films by solvents or gases. Here, we use a novel in situ microfluidics-grazing incidence small-angle X-ray scattering (GISAXS) setup to examine changes in film thickness and in the surface structure of a thin polymer film that sorbs a good solvent. Thus, this technique is highly complementary to the established techniques on the field of diffusion in polymers. The initial stages of water uptake and swelling are resolved for a 50 nm thin, hydrophilic poly(N-isopropylacrylamide) (PNIPAM) film, before its dissolution sets in. The initial stages of swelling are tentatively described by anomalous swelling induced by a time- and space-dependent diffusion coefficient.

Distortion of Ultrathin Photocleavable Block Copolymer Films during Photocleavage and Nanopore Formation.

Highly ordered block copolymer thin films have been studied extensively during the last years because they afford versatile self-assembled morphologies via a bottom-up approach. They promise to be used in applications such as polymeric membranes or templates for nanostructured materials. Among the block copolymer structures, perpendicular cylinders have received strong attention due to their ability to fabricate highly ordered nanopores and nanowires. Nanopores can be created from a thin block copolymer film upon the removal of one block by selective etching or by dissolution of one polymer block. Here we demonstrate the utilization of polystyrene-block-poly(ethylene oxide) diblock copolymer (PS-hν-PEO) with an ortho-nitrobenzyl ester (ONB) as the photocleavable block-linker to create highly ordered thin films. Removal of the PEO block by choosing an appropriate solvent upon photocleavage is expected to yield arrays of nanopores decorated with functional groups, thus lending itself to adsorption or filtration uses. While the feasibility of this approach has been demonstrated, it is crucial to understand the influence of removal conditions (i.e., efficiency of photocleavage as well as best washing solvent) and to evaluate changes in the surface topology and inner structure upon photocleavage. To this end, the time dependence evolution of the surface morphology of block copolymer thin films was studied using grazing-incidence small-angle X-ray scattering (GISAXS) technique in combination with scanning probe microscopy.

Fast diffusion-limited lyotropic phase transitions studied in situ using continuous flow microfluidics/microfocus-SAXS.

Fast concentration-induced diffusion-limited lyotropic phase transitions can be studied in situ with millisecond time resolution using continuous flow microfluidics in combination with microfocus small-angle X-ray scattering. The method was applied to follow a classical self-assembly sequence where amphiphiles assemble into micelles, which subsequently assemble into an ordered lattice via a disorder/order transition. As a model system we selected the self-assembly of an amphiphilic block copolymer induced by the addition of a nonsolvent. Using microchannel hydrodynamic flow-focusing, large concentration gradients can be generated, leading to a deep quench from the miscible to the microphase-separated state. Within milliseconds the block copolymers assembly via a spinodal microphase separation into micelles, followed by a disorder/order transition into an FCC liquid-crystalline phase with late-stage domain growth and shear-induced domain orientation into a mesocrystal. A comparison with a slow macroscopic near-equilibrium kinetic experiment shows that the fast structural transitions follow a direct pathway to the equilibrium structure without the trapping of metastable states.

Studying nanostructure gradients in injection-molded polypropylene/montmorillonite composites by microbeam small-angle x-ray scattering.

The core-shell structure in oriented cylindrical rods of polypropylene (PP) and nanoclay composites (NCs) from PP and montmorillonite (MMT) is studied by microbeam small-angle x-ray scattering (SAXS). The structure of neat PP is almost homogeneous across the rod showing regular semicrystalline stacks. In the NCs the discrete SAXS of arranged crystalline PP domains is limited to a skin zone of 300 µm thickness. Even there only frozen-in primary lamellae are detected. The core of the NCs is dominated by diffuse scattering from crystalline domains placed at random. The SAXS of the MMT flakes exhibits a complex skin-core gradient. Both the direction of the symmetry axis and the apparent perfection of flake-orientation are varying. Thus there is no local fiber symmetry, and the structure gradient cannot be reconstructed from a scan across the full rod. To overcome the problem the rods are machined. Scans across the residual webs are performed. For the first time webs have been carved out in two principal directions. Comparison of the corresponding two sets of SAXS patterns demonstrates the complexity of the MMT orientation. Close to the surface (< 1 mm) the flakes cling to the wall. The variation of the orientation distribution widths indicates the presence of both MMT flakes and grains. The grains have not been oriented in the flowing melt. An empirical equation is presented which describes the variation from skin to core of one component of the inclination angle of flake-shaped phyllosilicate filler particles.

INSIGHT: in situ heuristic tool for the efficient reduction of grazing-incidence X-ray scattering data.

INSIGHT is a Python-based software tool for processing and reducing 2D grazing-incidence wide- and small-angle X-ray scattering (GIWAXS/GISAXS) data. It offers the geometric transformation of the 2D GIWAXS/GISAXS detector image to reciprocal space, including vectorized and parallelized pixel-wise intensity correction calculations. An explicit focus on efficient data management and batch processing enables full control of large time-resolved synchrotron and laboratory data sets for a detailed analysis of kinetic GIWAXS/GISAXS studies of thin films. It processes data acquired with arbitrarily rotated detectors and performs vertical, horizontal, azimuthal and radial cuts in reciprocal space. It further allows crystallographic indexing and GIWAXS pattern simulation, and provides various plotting and export functionalities. Customized scripting offers a one-step solution to reduce, process, analyze and export findings of large in situ and operando data sets.

Insulator Polymer Matrix Construction on All-Small-Molecule Photoactive Blend Towards Extrapolated 15000 Hour T80 Stable Devices.

To boost the stability of all-small-molecule (ASM) organic photovoltaic (OPV) blends, an insulator polymer called styrene-ethylene-butylene-styrene (SEBS) as morphology stabilizer is applied into the host system of small molecules BM-ClEH:BO-4Cl. Minor addition of SEBS (1 mg/ml in host solution) provides a significantly enhanced T80 value of 15000 hours (extrapolated), surpassing doping-free (0 mg/ml) and heavy doping (10 mg/ml) counterparts (900 hours, 30 hours). The material reproducibility and cost-effectiveness of the active layer will not be affected by this industrially available polymer, where the power conversion efficiency (PCE) can be well maintained at 15.02%, which is still a decent value for non-halogen solvent-treated ASM OPV. Morphological and photophysical characterizations clearly demonstrate SEBS's pivotal effect on suppressing the degradation of donor molecules and blend film's crystallization/aggregation reorganization, which protects the exciton dynamics effectively. This work pays meaningful attention to the ASM system stability, performs a smart strategy to suppress the film morphology degradation, and releases a comprehensive understanding of the mechanism of device performance reduction.

A Practical Approach Toward Highly Reproducible and High-Quality Perovskite Films Based on an Aging Treatment.

Solution processing of hybrid perovskite semiconductors is a highly promising approach for the fabrication of cost-effective electronic and optoelectronic devices. However, challenges with this approach lie in overcoming the controllability of the perovskite film morphology and the reproducibility of device efficiencies. Here, a facile and practical aging treatment (AT) strategy is reported to modulate the perovskite crystal growth to produce sufficiently high-quality perovskite thin films with improved homogeneity and full-coverage morphology. The resulting AT-films exhibit fewer defects, faster charge carrier transfer/extraction, and suppressed non-radiative recombination compared with reference. The AT-devices achieve a noticeable improvement in the reproducibility, operational stability, and photovoltaic performance of devices, with the average efficiency increased by 16%. It also demonstrates the feasibility and scalability of AT strategy in optimizing the film morphology and device performance for other perovskite components including MAPbI3 , (MAPbBr3 )15 (FAPbI3 )85 , and Cs0.05 (MAPbBr3 )0.17 (FAPbI3 )0.83 . This method opens an effective avenue to improve the quality of perovskite films and photovoltaic devices in a scalable and reproducible manner.

Operando Study Insights into Lithiation/Delithiation Processes in a Poly(ethylene oxide) Electrolyte of All-Solid-State Lithium Batteries by Grazing-Incidence X-ray Scattering.

Poly(ethylene oxide) (PEO)-based composite electrolytes (PCEs) are considered as promising candidates for next-generation lithium-metal batteries (LMBs) due to their high safety, easy fabrication, and good electrochemical stability. Here, we utilize operando grazing-incidence small-angle and wide-angle X-ray scattering to probe the correlation of electrochemically induced changes and the buried morphology and crystalline structure of the PCE. Results show that the two irreversible reactions, PEO-Li+ reduction and TFSI- decomposition, cause changes in the crystalline structure, array orientation, and morphology of the PCE. In addition, the reversible Li plating/stripping process alters the inner morphology, especially the PEO-LiTFSI domain radius and distance between PEO-LiTFSI domains, rather than causing crystalline structure and orientation changes. This work provides a new path to monitor a working battery in real time and to a detailed understanding of the Li+ diffusion mechanism, which is essential for developing highly transferable and interface-stable PCE-based LMBs.

Donor-Acceptor Copolymer with a Linear Backbone Induced Ordered and Robust Doping Morphology for Efficient and Stable Organic Electrochemical Devices.

Donor (D)-acceptor (A) copolymer-based organic mixed ionic-electronic conductors (OMIECs) exhibit intrinsic environmental stability for they have tailored energy levels. However, their figure-of-merit (µC*) is still falling behind the D-D polymers because of morphology deterioration during the electrochemical doping process. Herein, we developed two D-A copolymers with precisely regulated backbone curvature, namely PTBT-P and PTTBT-P. Compared to the curved PTBT-P and previously reported copolymers, PTTBT-P better keeps its backbone linear, leading to a long-range ordered doping morphology, which is revealed by the in operando X-ray technique. This optimized doping morphology enables a significantly improved operando charge mobility (µ) of 2.44 cm2 V-1 s-1 and a µC* value of 342 F cm-1 V-1 s-1, one of the highest values in D-A copolymer based on OECTs. Besides, we fabricated PTTBT-P-based electrochemical random-access memories and achieved ideal and robust conductance modulation. This study highlights the critical role of backbone curvature control in the optimization of doping morphology for efficient and robust organic electrochemical devices.