Effective degradation of bentazone by two-dimensional and three-phase, three-dimensional electro-oxidation system: kinetic studies and optimization using ANN.

Bentazone is a broad-leaved weed-specific herbicide in the pesticide industry. This study focused on removing bentazone from water using three different methods: a two and three-dimensional electro-oxidation process (2D/EOP and 3D/EOP) with a fluid-type reactor arrangement using tetraethylenepentamine-loaded particle electrodes and an adsorption method. Additionally, we analysed the effects of two types of supporting electrolytes  (Na2SO4 and NaCl) on the degradation process. The energy consumption amounts were calculated to evaluate the obtained results. The degradation reaction occurs 3.5 times faster in 3D/EOP than in 2D/EOP at 6 V in Na2SO4. Similarly, the degradation reaction of bentazone in NaCl occurs 2.5 times faster in 3D/EOP than in 2D/EOP at a value of 7.2 mA/cm2. Removal of bentazone is significantly better in 3D/EOPs than in 2D/EOPs. The use of particle electrodes can significantly enhance the degradation efficiency. The study further assessed the prediction abilities of the machine learning model (ANN). The ANN presented reasonable accuracy in bentazone degradation with high R2 values of 0.97953, 0.98561, 0.98563, and 0.99649 for 2D with Na2SO4, 2D with NaCl, 3D with Na2SO4, and 3D with NaCl, respectively.

Synthesis and characterization of cylindrical electrode with sucrose binder as advanced electrode materials for copper 3D-electro-oxidation.

This study produced a biomass-based cylindrical electrode containing sucrose (an organic binder). The Cu2+ removal performance of the synthesized sucrose-bonded cylindrical electrode was evaluated in a 3-phase 3-dimensional electro-oxidation reactor (3D-EO) and the classical electro-oxidation method (2D-EO). Sodium Dodecyl Sulfate (SDs) was grafted onto activated carbon and used as microelectrode in 3D-EO reactors. SDs grafting resulted in a 57% reduction in the micropores of activated carbon. Therefore, the surface area of carbon after grafting decreased from 1328 m2/g to 580 m2/g. The sucrose-bonded cylindrical electrode has a rich carbon structure and consists of 84.04 wt% C, 12.10 wt% O and 3.20 wt%Si. According to CV measurement, the sucrose-bonded cylindrical electrode gives a surface reaction against Cu2+ at voltages lower than -0.62 V. Increasing the potential difference from 1V to 3V in 2D-EO and 3D-EO processes led to the removal of Cu2+ from the solution. The 3D-EO reactor achieved a removal rate of 87.12% at 3V. The 100 ppm solution was treated with a 3D-EO reactor containing 6 g/L of PC/SDs400Ws for 60 min, successfully removing 91.22% of Cu2+.

Optimization of the effect of microelectrodes on Ni2+ removal in three-dimensional electrode system.

This study investigated Ni+2 removal performance in 3DER reactors where electrocoagulation mechanisms and microelectrodes are used together. EDTA modification was carried out on the granule-activated carbon surface to increase the efficiency and affinity of microelectrodes against Ni+2 molecules. The grafting was examined using BET, FT-IR, SEM, EDS, and the elemental mapping methods. With the surface analyses made in this study, it was revealed that EDTA modification on granulated activated carbon was successfully performed. Also, 8.48%wt by mass of EDTA grafting on granular activated carbon was possible. EDTA functionalization did not affect the surface pore structures of CAC much. Under 10 V potential, 97.82% Ni removal efficiency was obtained with 2D in 35 min, while 96.69% removal in 10 min and 100% removal in 15 min were obtained in the 3D reactor. The Ni+2 removal mechanism in 3DER reactors has been determined to conform to the pseudo-second-order kinetic model. The k2 value obtained for 10 V (1.36 10-2) is 27 times the k2 value obtained for 5 V for 3DER reactors. In addition, using central composite design (CCD), operational parameters such as time, concentration, and potential difference affecting Ni+2 removal in 3DER reactors have been optimized. The most influential parameter is the applied voltage, followed by time and concentration. It has been determined that 3DER reactors using EDTA-modified microelectrodes are highly efficient and suitable for Ni+2 removal.