Polarization-enhanced cell walls etching of anodic titanium oxide.

Anodic titanium oxide (ATO) photonic crystals (PhCs) are promising for photonics, photocatalysis, and solar cells. A refractive index modulation in ATO PhCs is caused by the modulation of porosity and, thus, the pore diameter should be controlled precisely. The ATO cell walls etching in electrolyte solution during anodizing increases the porosity of the PhC structure and shifts the photonic band gap (PBG) position to shorter wavelengths. Until now, the ATO cell walls etching in organic based electrolytes has been associated solely with the chemical dissolution of ATO in fluoride-containing solutions. Here, a significant enhancement of cell walls etching is observed when electric current flows under anodic polarization. This effect leads to the blue shift of the PBG position with the number of periods of ATO PhC structure. Therefore, it is essential for the synthesis of ATO PhCs with a precise PBG position.

Three-Dimensional Photonic Crystals Based on Porous Anodic Aluminum Oxide.

Photonic crystals (PCs) consisting of a periodic arrangement of holes in dielectric media have found success in light manipulation and sensing. Among them, three-dimensional (3D) PCs are in high demand due to their unique properties originating from multiple photonic band gaps (PBGs) and even full ones. Here, 3D PCs based on porous anodic aluminum oxide (AAO) were fabricated for the first time. Our approach involves prepatterning of the aluminum surface by a focused ion beam to form a hexagonal array of pore nuclei. Subsequent anodization in 1 M H3PO3 using a sine wave profile of voltage provides AAO with a defect-free in-plane porous structure and out-of-plane porosity modulation. The ability to tune the position, width, and depth of the PBGs is demonstrated. The combination of the flexibility of the proposed approach with the unique properties of AAO extends the range of practical applications of 3D PCs far beyond the current achievements.

One-Dimensional Photonic Crystals with Nonbranched Pores Prepared via Phosphorous Acid Anodizing of Aluminium.

One-dimensional photonic crystals (1D PhCs) obtained by aluminium anodizing under oscillating conditions are promising materials with structure-dependent optical properties. Electrolytes based on sulphuric, oxalic, and selenic acids have been utilized for the preparation of anodic aluminium oxide (AAO) 1D PhCs with sub-100-nm pore diameter. AAO films with larger pores can be obtained by anodizing in phosphorous acid at high voltages. Here, for the first time, anodizing in phosphorous acid is applied for the preparation of AAO 1D PhCs with nonbranched macropores. The sine wave profile of anodizing voltage in the 135-165 V range produces straight pores, whose diameter is above 100 nm and alternates periodically in size. The pore diameter modulation period linearly increases with the charge density by a factor of 599 ± 15 nm·cm2·C-1. The position of the photonic band gap is controlled precisely in the 0.63-1.96 µm range, and the effective refractive index of AAO 1D PhCs is 1.58 ± 0.05.

Fabrication of artificial opals by electric-field-assisted vertical deposition.

We present a new technique for large-scale fabrication of colloidal crystals with controllable quality and thickness. The method is based on vertical deposition in the presence of a DC electric field normal to the conducting substrate. The crystal structure and quality are quantitatively characterized by microradian X-ray diffraction, scanning electron microscopy, and optical reflectometry. Attraction between the charged colloidal spheres and the substrate promotes growth of thicker crystalline films, while the best-quality crystals are formed in the presence of repulsion. Highly ordered thick crystalline layers with a small amount of stacking faults and a low mosaic spread can be obtained by optimizing the growth conditions.

Titania Photonic Crystals with Precise Photonic Band Gap Position via Anodizing with Voltage versus Optical Path Length Modulation.

Photonic crystals based on titanium oxide are promising for optoelectronic applications, for example as components of solar cells and photodetectors. These materials attract great research attention because of the high refractive index of TiO2. One of the promising routes to prepare photonic crystals based on titanium oxide is titanium anodizing at periodically changing voltage or current. However, precise control of the photonic band gap position in anodic titania films is a challenge. To solve this problem, systematic data on the effective refractive index of the porous anodic titanium oxide are required. In this research, we determine quantitatively the dependence of the effective refractive index of porous anodic titanium oxide on the anodizing regime and develop a model which allows one to predict and, therefore, control photonic band gap position in the visible spectrum range with an accuracy better than 98.5%. The prospects of anodic titania photonic crystals implementation as refractive index sensors are demonstrated.

Double stacking faults in convectively assembled crystals of colloidal spheres.

Using microradian X-ray diffraction, we investigated the crystal structure of convectively assembled colloidal photonic crystals over macroscopic (0.5 mm) distances. Through adaptation of Wilson's theory for X-ray diffraction, we show that certain types of line defects that are often observed in scanning electron microscopy images of the surface of these crystals are actually planar defects at 70.5 degrees angles with the substrate. The defects consist of two parallel hexagonal close-packed planes in otherwise face-centered cubic crystals. Our measurements indicate that these stacking faults cause at least 10% of stacking disorder, which has to be reduced to fabricate high-quality colloidal photonic crystals.