Laser cooling ytterbium doped silica by 67 K from ambient temperature.

Laser cooling of a 5 cm long, 1 mm diameter ytterbium doped (6.56×1025 ions/m3) silica rod by 67 K from room temperature was achieved. For the pump source, a 100 W level ytterbium fiber amplifier was constructed along with a 1032 nm fiber Bragg grating seed laser. Experiments were done in vacuum and monitored with the non-contact differential luminescence thermometry method. Direct measurements of the absorption spectrum as a function of temperature were made, to avoid any possible ambiguities from site-selectivity and deviations from McCumber theory at low temperature. This allowed direct computation of the cooling efficiency versus temperature at the pump wavelength, permitting an estimated heat lift of 1.42 W/m as the sample cooled from ambient temperature to an absolute temperature of 229 K.

TMI and polarization static energy transfer in Yb-doped low-NA PM fibers.

In this work, we conduct experimental investigations of transverse mode instabilities (TMI) in a large mode area ultra-low numerical aperture polarization maintaining fiber amplifier. This fiber is few mode in the slow-axis (conventional operation mode), but single mode in the fast-axis. We test the stability of the output beam by changing the input polarization angle and systematically investigate the transverse mode instability threshold in the two principal polarization axes. The lowest TMI threshold at 300 W was found when the input polarization angle was aligned parallel to the slow-axis. Detuning the input polarization angle from the slow-axis led to increased TMI thresholds. For input polarization angle of 90° (parallel to the fast-axis), the output signal was stable up to 475 W and further scaling was limited by the available pump power. However, for fast-axis operation a lower polarization ratio compared to slow-axis operation was observed as well as an unexpected static energy transfer from the fast-axis into the slow-axis above 400 W.

Mitigation of transverse mode instability by modal birefringence in polarization-maintaining fibers.

The effect of transverse mode instability (TMI) poses a fundamental obstacle for a further scaling of diffraction-limited, high-power fiber laser systems. In this work we present a theoretical and experimental study on the mitigation of TMI by modal birefringence in a polarization maintaining (PM) fiber. With the help of comprehensive simulations, we show that the thermally-induced refractive index grating responsible for TMI can be modified and washed out when light is coupled with a polarization input angle detuned from the main axes of the fiber. To confirm the theoretical predictions, we have designed and manufactured an Yb-doped large-mode-area PM fiber. Using this fiber, we have systematically investigated the dependence of the TMI threshold on the polarization input angle of the seed laser. We experimentally demonstrate that when the polarization input angle of the seed is aligned at 50° with respect to the slow-axis, the TMI threshold increases by a factor of 2, verifying the theory and the numerical simulations. A high speed polarization mode-resolved analysis of the output beam is presented, which reveals that at the onset of TMI both polarization axes fluctuates simultaneously.

Polarization-resolved mode evolution in TMI-limited Yb-doped fiber amplifiers using a novel high-speed Stokes polarimeter.

In this work we have developed a high-speed Stokes polarimeter method based on simultaneous 4-channel imaging with a high-speed camera. Thus, current speed limitations of imaging polarimeters for wavelengths around 1 µm can be overcome, allowing a sub-ms polarization-resolved characterization of transverse mode instability (TMI). Additionally, the Stokes parameters of each individual mode are calculated by a simultaneous 4-beam mode reconstruction algorithm during post-processing and can be analyzed with unprecedented temporal resolution. We demonstrate the measurement capabilities of this polarimeter setup by characterizing TMI of a large-mode-area Yb-doped polarization maintaining (PM) fiber amplifier with 30 kHz video frame rate. Upon thorough characterization, we have found for the first time that at the onset of TMI in a PM fiber, the modal polarization states begin to oscillate on circular and elliptical trajectories at the same frequencies as the modal energy transfer occurs. The ability to measure the modal polarization states with sub-ms temporal resolution is key to developing a fundamental understanding and subsequently possible mitigation strategies of TMI in PM-fiber lasers.

Potential of ytterbium doped silica glass for solid-state optical refrigeration to below 200 K.

We report on the optical refrigeration of ytterbium doped silica glass by >40 K starting at room temperature, which represents more than a two-fold improvement over the previous state-of-the-art. A spectroscopic investigation of the steady-state and time-dependent fluorescence was carried out over the temperature range 80 K to 400 K. The calculated minimum achievable temperature for our Yb3+ doped silica sample is ≈150 K, implying the potential for utilizing ytterbium doped silica for solid-state optical refrigeration below temperatures commonly achieved by standard Peltier devices.

Impact of site-selective spectroscopy on laser cooling parameter characterization.

From laser design to optical refrigeration, experimentally measured fluorescence spectra are often utilized to obtain input parameters for predictive models. However, in materials that exhibit site-selectivity, the fluorescence spectra depend on the excitation wavelength employed to take the measurement. This work explores different conclusions that predictive models reach after inputting such varied spectra. Here, temperature-dependent site-selective spectroscopy is carried out on an ultra-pure Yb, Al co-doped silica rod fabricated by the modified chemical vapor deposition technique. The results are discussed in the context of characterizing ytterbium doped silica for optical refrigeration. Measurements made between 80 K and 280 K at several different excitation wavelengths yield unique values and temperature dependencies of the mean fluorescence wavelength. For the excitation wavelengths studied here, the variation in emission lineshapes ultimately lead to calculated minimum achievable temperatures (MAT) ranging between 151 K and 169 K, with theoretical optimal pumping wavelengths between 1030 nm and 1037 nm. Direct evaluation of the temperature dependence of the fluorescence spectra band area associated with radiative transitions out of the thermally populated 2F5/2 sublevel may be a better approach to identifying the MAT of a glass where site-selective behavior precludes unique conclusions.

Frequency-doubled Q-switched 4 × 4 multicore fiber laser system.

Frequency doubling of a Q-switched Yb-doped rod-type 4 × 4 multicore fiber (MCF) laser system is reported. A second harmonic generation (SHG) efficiency of up to 52% was achieved with type I non-critically phase-matched lithium triborate (LBO), with a total SHG pulse energy of up to 17 mJ obtained at 1 kHz repetition rate. The dense parallel arrangement of amplifying cores into a shared pump cladding enables a significant increase in the energy capacity of active fibers. The frequency-doubled MCF architecture is compatible with high-repetition-rate and high-average-power operation and may provide an efficient alternative to bulk solid-state systems as pump sources for high-energy titanium-doped sapphire lasers.

High-energy Q-switched 16-core tapered rod-type fiber laser system.

High-energy Q-switched master oscillator power amplifier systems based on rod-type 4 × 4 multicore fibers are demonstrated, achieving energy up to 49 mJ in ns-class pulses. A tapered fiber geometry is tested that maintains low mode order in large multimode output cores, improving beam quality in comparison to a similar fiber with no taper. The tapered fiber design can be scaled both in the number of amplifying cores and in the dimensions of the cores themselves, providing a potential route toward joule-class fiber lasers systems.

500†W rod-type 4 × 4 multicore ultrafast fiber laser.

We present a coherently combined femtosecond fiber chirped-pulse-amplification system based on a rod-type, ytterbium-doped, multicore fiber with 4 × 4 cores. A high average power of up to 500 W (after combination and compression) could be achieved at 10 MHz repetition rate with excellent beam quality. Additionally, < 500 fs pulses with up to 600 µJ of pulse energy were also realized with this setup. This architecture is intrinsically power scalable by increasing the number of cores in the fiber.

Laser cooling experiments to measure the quantum efficiency of Yb-doped silica fibers.

A detailed investigation into the wavelength-dependent cooling efficiencies of two ultra-pure large core diameter ytterbium-doped silica fibers is carried out by means of the laser-induced thermal modulation spectroscopy (LITMoS) method. From these measurements, an external quantum efficiency of 0.99 is obtained for both fibers. Optimal cooling is seen for pump wavelengths between 1032 and 1035 nm. The crossover wavelength from heating to cooling is identified to be between 1018 and 1021 nm. The fiber with higher Yb3+ ion density exhibits better cooling, seen by the input power normalized temperature differential.

Experimental analysis of Raman-induced transverse mode instability in a core-pumped Raman fiber amplifier.

The effect of transverse mode instability is a limitation for the power scaling of fiber laser systems, that can originate due to heat caused by stimulated Raman scattering. In this contribution, we experimentally investigate the threshold of transverse mode instability caused by stimulated Raman scattering in a passive fiber. Both, the Stokes seed power and the fiber length of a core-pumped Raman fiber amplifier are varied to systematically study this effect. Mode resolved measurements reveal that the threshold occurs at approximately the same Stokes output power for all tested configurations, independent of the total Raman conversion efficiency. These results increase the understanding of this type of mode instability and show which parameters are important for a further power scaling of high-power Raman fiber amplifiers.

Continuous-wave cascaded second Stokes diamond Raman laser at 1477 nm.

We report a high brightness cascaded Stokes diamond Raman laser with a diffraction limited beam quality pumped by an Yd-doped fiber laser. The Raman laser operated at 1477 nm and reached an output power of 63 W with 214 W pump power in continuous-wave mode. Conversion efficiency over 30% was achieved using a single pump pass concentric cavity that was highly resonant at the first Stokes and had high outcoupling at the second Stokes (45%). Thermal limitations were investigated as well as the temporal behavior of the first and second Stokes intra-cavity power.

Laser cooling of a Yb doped silica fiber by 18 Kelvin from room temperature.

An ytterbium doped silica optical fiber with a core diameter of 900µm has been cooled by 18.4 K below ambient temperature by pumping with 20 W of 1035 nm light in vacuum. In air, cooling by 3.6 K below ambient was observed with the same 20 W pump. The temperatures were measured with a thermal imaging camera and differential luminescence thermometry. The cooling efficiency is calculated to be 1.2±0.1%. The core of the fiber was codoped with Al3+ for an Al to Yb ratio of 6:1, to allow for a larger Yb concentration and enhanced laser cooling.

Transverse mode instability in a passive fiber induced by stimulated Raman scattering.

Transverse mode instabilities are a major limitation for power scaling of fiber lasers but have so far only been observed in laser-active fibers. In this contribution we present experimental observations of transverse mode instabilities in a passive fiber. In this fiber, stimulated Raman scattering acted as heat source. To demonstrate the effect, a kW-level ytterbium-doped fiber laser was used as pump for a Raman amplifier. Transverse mode instabilities were only observed in the case with high Raman amplification. Frequency resolved stability measurements at various fiber positions as well as spectral and mode resolved measurements pin their origin to the passive fiber. This observation might help to gain further understanding of transverse mode instabilities and shows limitations of high-power Raman amplifiers.

Highly customized 1010†nm, ns-pulsed Yb-doped fiber amplifier as a key tool for on-demand single-photon generation.

The development of highly customized technical devices is a decisive feature of technically complex setups, as frequently observed in quantum experiments. This paper describes the development and realization of an Yb-doped all-fiber amplifier system designed for such a special application, more specifically, an on-demand single-photon source based on four-wave mixing with rubidium Rydberg atoms. The laser is capable of generating bandwidth-limited configurable nanosecond pulses up to peak powers of >100 W and with pulse repetition frequencies (PRF) between 50 Hz and 1 MHz at selectable wavelengths (1008-1024 nm). Especially the amplification of the 1010 nm reference seed at the lower edge of the amplification range for Yb-based fibers is challenging and tends to produce amplified spontaneous emission (ASE) at higher wavelengths. To achieve high ASE suppression, particularly at low pulse repetition frequencies, two acousto-optical modulators (AOM) are utilized both for pulse picking and for temporal filtering. The synchronization between pulse repetition frequency and AOM driver signal allows pulse amplitude fluctuations to be kept below 1%, while ASE is suppressed by at least 85 dB (PRF = 1 MHz) and 65 dB (PRF = 1 kHz).

Diamond Raman oscillator operating at 1178 nm.

In this contribution, we report high-power Raman frequency downconversion based on an Yb-doped fiber amplifier and a linear external diamond Raman cavity. A maximum output power of 136 W with nearly diffraction-limited beam quality was achieved by pumping in quasi-continuous-wave mode with 10% duty cycle and 10 ms on-time duration. For continuous-wave operation, we achieved record average power of 46 W centered at 1178 nm. The emergence of stimulated Brillouin scattering in diamond is further investigated. This technology shows the potential to extend the spectral range of fiber lasers to reach uncommon wavelengths at high power levels.

Extremely robust femtosecond written fiber Bragg gratings for an ytterbium-doped fiber oscillator with 5 kW output power.

We present highly robust fiber Bragg gratings (FBGs) in passive large-mode-area fibers for kilowatt fiber laser systems. The gratings were inscribed directly through the fiber coating using near-infrared femtosecond laser pulses and then implemented in an all-fiber ytterbium-doped single-mode oscillator setup reaching up to 5 kW signal output power. The untreated cooled FBGs showed thermal coefficients as low as ${1}\;{\rm K}\;{{\rm kW}^{ - 1}}$1KkW-1, proving excellent qualification for the implementation into robust high-power fiber laser setups.

Femtosecond written fiber Bragg gratings in ytterbium-doped fibers for fiber lasers in the kilowatt regime.

We investigate the high-power durability of fiber Bragg gratings written directly into an ytterbium-doped large mode area fiber using ultrashort laser pulses. The gratings were successfully integrated as a high reflector into an oscillator setup reaching up to 1.9 kW signal output power with an efficiency of 87%. Defect states induced during the inscription process could be drastically reduced by a self-annealing process resulting in a stable laser performance.

Ring-up-doped fiber for the generation of more than 600 W single-mode narrow-band output at 1018 nm.

We present the amplification of a narrow-bandwidth signal at a wavelength of 1018 nm to a power exceeding 600 W with a stable output polarization state. The beam showed an excellent, nearly diffraction-limited beam quality. The high-power output could be realized using an in-house designed and fabricated fiber with a core-cladding diameter ratio of 32/260, ultra-low NA of 0.041, and ring-up doping. A seed source with high amplified spontaneous emission (ASE) suppression was also required, which was realized by a double-pass pre-amplifier with 13 W output power.

Experimental investigations on the TMI thresholds of low-NA Yb-doped single-mode fibers.

In this contribution we investigate the transversal mode instability behavior of a ytterbium-doped commercial 20/400 fiber and obtain 2.9 kW of output power after optimizing the influencing parameters. In this context, we evaluate the influence of the bend diameter and the pump wavelength within the scope of the absorption length and the length of the fiber. Furthermore, with a newly developed fiber we report on 4.4 kW of single-mode output power at 40 cm bend diameter.