Application of transition-edge sensors for micro-X-ray fluorescence measurements and micro-X-ray absorption near edge structure spectroscopy: a case study of uranium speciation in biotite obtained from a uranium mine.

In this study, we successfully applied a transition-edge sensor (TES) spectrometer as a detector for microbeam X-ray measurements from a synchrotron X-ray light source in the hard X-ray region to determine uranium (U) distribution at the micro-scale and its chemical species in biotite obtained from a U mine. It is difficult to separate the fluorescent X-ray of the U Lα1 line at 13.615 keV from that of the Rb Kα line at 13.395 keV in the X-ray fluorescence spectrum with an energy resolution of approximately 220 eV using a conventional silicon drift detector (SDD). Meanwhile, the fluorescent X-rays of U Lα1 and Rb Kα were fully separated by a TES with 50 eV energy resolution at an energy of around 13 keV. The successful peak separation by the TES led to an accurate mapping analysis of trace U in micro-X-ray fluorescence measurements and a decrease in the signal-to-background ratio in micro-X-ray absorption near edge structure spectroscopy. Thus, it could be a powerful tool for studying the U distribution and speciation in various environmental samples.

Oxidation and phase transfer of individual Cr-doped dendritic FeOx particles visualized by full-field nano-XAFS spectroimaging.

Iron oxides with various compositions and polymorphs have been widely used as compounds that require reversible redox properties, such as catalysts. However, partial decomposition during phase transitions often causes irreversible degradation of the redox properties of iron oxides. Cr doping into the crystalline framework of iron oxide dendrites improves the stability of the structural transformation of iron oxides. We spatially visualized the FeOx-dendrite phase distribution during oxidation in crystalline dendritic FeOx and Cr-FeOx particles by full-field nano-X-ray absorption fine structure spectroimaging. The spectroimaging visualized propagation in the phase transitions in the individual FeOx particles and changes in the phase transition behaviors of the Cr-FeOx particles. The statistical analysis of the spectroimaging data revealed the phase transition trends in parts of the FeOx and Cr-FeOx particles in three Fe density zones (particle thicknesses) and the probability densities of the phase proportions in the dendrites.

Quantitative evaluation of the intratumoral distribution of platinum in oxaliplatin-treated rectal cancer: In situ visualization of platinum via synchrotron radiation X-ray fluorescence spectrometry.

Oxaliplatin (l-OHP), a platinum-based drug, is a key chemotherapeutic agent for colorectal cancer (CRC), but drug resistance and toxic effects have been major limitations of its use. Synchrotron radiation X-ray fluorescence spectrometry (SR-XRF) is a rapid, nondestructive technique for monitoring the distribution of metals and trace elements in cells or tissue samples. We applied SR-XRF to visualize the distribution of platinum and other elements in 30 rectal cancer specimens resected from patients who received l-OHP-based preoperative chemotherapy and quantified platinum concentration in the tumor epithelium and stroma, respectively, using calibration curves. The platinum concentration in rectal cancer tissue ranged 2.85-11.44 ppm, and the detection limit of platinum was 1.848 ppm. In the tumor epithelium, the platinum concentration was significantly higher in areas of degeneration caused by chemotherapy than in nondegenerated area (p < 0.001). Conversely, in the tumor stroma, the platinum concentration was significantly higher in patients with limited therapeutic responses than in those with strong therapeutic responses (p < 0.001). Furthermore, multivariate analysis illustrated that higher platinum concentration in the tumor stroma was an independent predictive factor of limited histologic response (odds ratio; 19.99, 95% confidence interval; 2.04-196.37, p = 0.013). This is the first study to visualize and quantify the distribution of platinum in human cancer tissues using SR-XRF. These results suggest that SR-XRF analysis may contribute to predicting the therapeutic effect of l-OHP-based chemotherapy by quantifying the distribution of platinum.

Model building analysis - a novel method for statistical evaluation of Pt L3-edge EXAFS data to unravel the structure of Pt-alloy nanoparticles for the oxygen reduction reaction on highly oriented pyrolytic graphite.

Extended X-ray absorption fine structure (EXAFS) is a powerful tool to determine the local structure in Pt nanoparticles (NP) on carbon supports, active catalysts for fuel cells. Highly oriented pyrolytic graphite (HOPG) covered with Pt NP gives samples with flat surfaces that allow application of surface science techniques. However, the low concentration of Pt makes it difficult to obtain good quality EXAFS data. We have performed in situ highly sensitive BCLA-empowered Back Illuminated EXAFS (BCLA + BI-EXAFS) measurements on Pt alloy nanoparticles. We obtained high quality Pt L3-edge data. We have devised a novel analytical method (model building analysis) to determine the structure of multi-component nanoparticles from just a single absorption edge. The generation of large numbers of structural models and their comparison with EXAFS fits allows us to determine the structures of Pt-containing nanoparticles, catalysts for the oxygen reduction reaction. Our results show that PtCo, PtCoN and AuPtCoN form a Pt-shell during electrochemical dealloying and that the ORR activity is directly proportional to the Pt-Pt bond length.

SPring-8 BL36XU: Synchrotron Radiation X-Ray-Based Multi-Analytical Beamline for Polymer Electrolyte Fuel Cells under Operating Conditions.

We designed and constructed a beamline BL36XU at the 8 GeV synchrotron radiation facility SPring-8 to provide information required for the development of next-generation polymer electrolyte fuel cells (PEFCs) by clarifying the dynamic aspects of structures and electronic states of cathode catalysts under PEFC operating conditions and in the deterioration processes by accelerated durability test protcols. To investigate the mechanism and degradation process for the cathode electrocatalysis in practical PEFCs, we developed advanced time- and spatially-resolved in-situ/operando X-ray absorption fine structure measurement systems and complementary analytical systems (X-ray emission spectroscopy (XES), X-ray diffraction (XRD), X-ray computer tomography (CT) and hard X-ray photoelectron spectroscopy (HAXPES)) and combined them to develop multi-analytical systems at BL36XU. Multi-analytical systems are very powerful for observing spatial-temporal features of the transient processes occurring in complex systems such as PEFCs. This account describes the design, performance, and research results of the BL36XU and multi-analytical in-situ/operando systems.

Operando XAFS Imaging of Distribution of Pt Cathode Catalysts in PEFC MEA.

Three-dimensional imaging using X-ray as a probe is state-of-the-art for the characterization of heterogeneous materials. In addition to simple imaging of sample morphology, imaging of elemental distribution and chemical states provides advanced maps of key structural parameters of functional materials. The combination of X-ray absorption fine structure (XAFS) spectroscopy and three-dimensional imaging such as computed tomography (CT) can visualize the three-dimensional distribution of target elements, their valence states, and local structures in a non-destructive manner. In this personal account, our recent results on the three-dimensional XAFS imaging for Pt cathode catalysts in the membrane electrode assembly (MEA) of polymer electrolyte fuel cell (PEFC) are introduced. The distribution and chemical states of Pt cathode catalysts in MEAs remarkably change under PEFC operating conditions, and the 3D XAFS imaging revealed essential events in PEFC MEAs.

Development of Surface Fluorescence X-Ray Absorption Fine Structure Spectroscopy Using a Laue-Type Monochromator.

Surface fluorescence X-ray absorption fine structure (XAFS) spectroscopy using a Laue-type monochromator has been developed to acquire structural information about metals with a very low concentrate on a flat highly oriented pyrolytic graphite (HOPG) surface in the presence of electrolytes. Generally, surface fluorescence XAFS spectroscopy is hindered by strong scattering from the bulk, which often chokes the pulse counting detector. In this work, we show that a bent crystal Laue analyzer (BCLA) can efficiently remove the scattered X-rays from the bulk even in the presence of solution. We applied the technique to submonolayer (∼1014  atoms cm-2 ) Pt on HOPG and successfully obtained high signal/noise in situ XAFS data in combination with back-illuminated fluorescence XAFS (BI-FXAFS) spectroscopy. This technique allows in situ XAFS measurements of flat electrode surfaces to be performed in the presence of electrolytes.

In situ study of oxidation states of platinum nanoparticles on a polymer electrolyte fuel cell electrode by near ambient pressure hard X-ray photoelectron spectroscopy.

We performed in situ hard X-ray photoelectron spectroscopy (HAXPES) measurements of the electronic states of platinum nanoparticles on the cathode electrocatalyst of a polymer electrolyte fuel cell (PEFC) using a near ambient pressure (NAP) HAXPES instrument having an 8 keV excitation source. We successfully observed in situ NAP-HAXPES spectra of the Pt/C cathode catalysts of PEFCs under working conditions involving water, not only for the Pt 3d states with large photoionization cross-sections in the hard X-ray regime but also for the Pt 4f states and the valence band with small photoionization cross-sections. Thus, this setup allowed in situ observation of a variety of hard PEFC systems under operating conditions. The Pt 4f spectra of the Pt/C electrocatalysts in PEFCs clearly showed peaks originating from oxidized Pt(ii) at 1.4 V, which unambiguously shows that Pt(iv) species do not exist on the Pt nanoparticles even at such large positive voltages. The water oxidation reaction might take place at that potential (the standard potential of 1.23 V versus a standard hydrogen electrode) but such a reaction should not lead to a buildup of detectable Pt(iv) species. The voltage-dependent NAP-HAXPES Pt 3d spectra revealed different behaviors with increasing voltage (0.6 → 1.0 V) compared with decreasing voltage (1.0 → 0.6 V), showing a clear hysteresis. Moreover, quantitative peak-fitting analysis showed that the fraction of non-metallic Pt species matched the ratio of the surface to total Pt atoms in the nanoparticles, which suggests that Pt oxidation only takes place at the surface of the Pt nanoparticles on the PEFC cathode, and the inner Pt atoms do not participate in the reaction. In the valence band spectra, the density of electronic states near the Fermi edge reduces with decreasing particle size, indicating an increase in the electrocatalytic activity. Additionally, a change in the valence band structure due to the oxidation of platinum atoms was also observed at large positive voltages. The developed apparatus is a valuable in situ tool for the investigation of the electronic states of PEFC electrocatalysts under working conditions.

Non-contact electric potential measurements of electrode components in an operating polymer electrolyte fuel cell by near ambient pressure XPS.

Photoelectron spectroscopy has the advantage of providing electric potentials by non-contact measurements based on the kinetic energy shift in component potential. We performed operando hard X-ray photoelectron spectroscopy (HAXPES) measurements with an 8 keV excitation source to measure the shift in electron kinetic energies as a function of the voltages of all the components at the anode and cathode electrodes of a polymer electrolyte fuel cell (PEFC). At the cathode electrode, when we increase the voltage between the cathode and anode from 0.2 to 1.2 V, the O 1s and F 1s peaks shift to a lower binding energy and the magnitude of the energy shift is equal to the voltage. The Pt 3d and C 1s peaks do not shift with the voltage since platinum nanoparticles and carbon supports at the cathode electrode have ground contact. In contrast to the cathode electrode, the peak shifts of all the components at the anode electrode show the same amount of shift as the voltages. It is clear that the change in the potential difference occurs only in an electrical double layer at the interface between the cathode electrode (Pt/C) and the electrolyte (Nafion and water), and that the anode electrode is in equilibrium as a pseudo-hydrogen electrode. Moreover, the electric potential variation of the cathode electrode in a PEFC under a power generation condition was also directly detected by operando HAXPES.

Operando 3D Visualization of Migration and Degradation of a Platinum Cathode Catalyst in a Polymer Electrolyte Fuel Cell.

The three-dimensional (3D) distribution and oxidation state of a Pt cathode catalyst in a practical membrane electrode assembly (MEA) were visualized in a practical polymer electrolyte fuel cell (PEFC) under fuel-cell operating conditions. Operando 3D computed-tomography imaging with X-ray absorption near edge structure (XANES) spectroscopy (CT-XANES) clearly revealed the heterogeneous migration and degradation of Pt cathode catalyst in an MEA during accelerated degradation test (ADT) of PEFC. The degradative Pt migration proceeded over the entire cathode catalyst layer and spread to MEA depth direction into the Nafion membrane.

Imaging of Oxygen Diffusion in Individual Platinum/Ce2 Zr2 Ox Catalyst Particles During Oxygen Storage and Release.

The spatial distribution of Ce(3+) and Ce(4+) in each particle of Ce2 Zr2 Ox in a three-way conversion catalyst system was successfully imaged during an oxygen storage/release cycle by scanning X-ray absorption fine structure (XAFS) using hard X-ray nanobeams. For the first time, nano-XAFS imaging visualized and identified the modes of non-uniform oxygen diffusion from the interface of Pt catalyst and Ce2 Zr2 Ox support and the active parts in individual catalyst particles.

Surface-Regulated Nano-SnO2/Pt3Co/C Cathode Catalysts for Polymer Electrolyte Fuel Cells Fabricated by a Selective Electrochemical Sn Deposition Method.

We have achieved significant improvements for the oxygen reduction reaction activity and durability with new SnO2-nanoislands/Pt3Co/C catalysts in 0.1 M HClO4, which were regulated by a strategic fabrication using a new selective electrochemical Sn deposition method. The nano-SnO2/Pt3Co/C catalysts with Pt/Sn = 4/1, 9/1, 11/1, and 15/1 were characterized by STEM-EDS, XRD, XRF, XPS, in situ XAFS, and electrochemical measurements to have a Pt3Co core/Pt skeleton-skin structure decorated with SnO2 nanoislands at the compressive Pt surface with the defects and dislocations. The high performances of nano-SnO2/Pt3Co/C originate from efficient electronic modification of the Pt skin surface (site 1) by both the Co of the Pt3Co core and surface nano-SnO2 and more from the unique property of the periphery sites of the SnO2 nanoislands at the compressive Pt skeleton-skin surface (more active site 2), which were much more active than expected from the d-band center values. The white line peak intensity of the nano-SnO2/Pt3Co/C revealed no hysteresis in the potential up-down operations between 0.4 and 1.0 V versus RHE, unlike the cases of Pt/C and Pt3Co/C, resulting in the high ORR performance. Here we report development of a new class of cathode catalysts with two different active sites for next-generation polymer electrolyte fuel cells.

Formation and nitrile hydrogenation performance of Ru nanoparticles on a K-doped Al2O3 surface.

Decarbonylation-promoted Ru nanoparticle formation from Ru3(CO)12 on a basic K-doped Al2O3 surface was investigated by in situ FT-IR and in situ XAFS. Supported Ru3(CO)12 clusters on K-doped Al2O3 were converted stepwise to Ru nanoparticles, which catalyzed the selective hydrogenation of nitriles to the corresponding primary amines via initial decarbonylation, the nucleation of the Ru cluster core, and the growth of metallic Ru nanoparticles on the surface. As a result, small Ru nanoparticles, with an average diameter of less than 2 nm, were formed on the support and acted as efficient catalysts for nitrile hydrogenation at 343 K under hydrogen at atmospheric pressure. The structure and catalytic performance of Ru catalysts depended strongly on the type of oxide support, and the K-doped Al2O3 support acted as a good oxide for the selective nitrile hydrogenation without basic additives like ammonia. The activation of nitriles on the modelled Ru catalyst was also investigated by DFT calculations, and the adsorption structure of a nitrene-like intermediate, which was favourable for high primary amine selectivity, was the most stable structure on Ru compared with other intermediate structures.

Visualization of the heterogeneity of cerium oxidation states in single Pt/Ce2Zr2O(x) catalyst particles by nano-XAFS.

The cerium oxidation states in single catalyst particles of Pt/Ce2Zr2O(x) (x=7 to 8) were investigated by spatially resolved nano X-ray absorption fine structure (nano-XAFS) using an X-ray nanobeam. Differences in the distribution of the Ce oxidation states between Pt/Ce2Zr2O(x) single particles of different oxygen compositions x were visualized in the obtained two-dimensional X-ray fluorescent (XRF) mapping images and the Ce L(III)-edge nano X-ray absorption near-edge structure (nano-XANES) spectra.

Performance and durability of Pt/C cathode catalysts with different kinds of carbons for polymer electrolyte fuel cells characterized by electrochemical and in situ XAFS techniques.

The electrochemical activity and durability of Pt nanoparticles on different kinds of carbon supports in oxygen reduction reactions (ORR) were investigated using rotating disc electrodes (RDE) and the membrane electrode assemblies (MEA) of polymer electrolyte fuel cells (PEFC). The mass activity of Pt/C catalysts (ORR activity per 1 mg of Pt) at the RDE decreased, according to the type of carbon support, in the following order; Ketjenblack (KB) > acetylene black (AB) > graphene > multiwall carbon nanotube (MW-CNT) > carbon black (CB), whereas the average size of the Pt nanoparticles and the surface specific activity (ORR activity per electrochemical surface area) did not vary significantly between these carbon supports. These results indicate that the different mass activities of the Pt/C catalysts may originate from the differences in the fraction of Pt on the carbon supports which is available for utilization. The durability of the MEAs of the top two active catalysts Pt/KB and Pt/AB among the five catalysts was examined based on ORR performance, TEM and in situ XAFS. It was found that the performance of the Pt/KB cathode catalyst in PEFC MEA decreased significantly over 500 accelerated durability test (ADT) cycles, whereas the performance of the Pt/AB cathode catalyst in PEFC MEA did not decrease significantly during 500 ADT cycles, it was also found that the Pt/AB possesses 8 times higher durability compared with the Pt/KB. In situ Pt LIII-edge XAFS data in the ADT cycles and stepwise potential operations revealed the different oxidation-reduction behaviors of the Pt nanoparticles on the KB and AB supports. The Pt/KB was oxidized to form surface PtO layers more easily than the Pt/AB in the increasing potential operation from 0.4 VRHE to 1.4 VRHE, and the surface PtO layers of the Pt/AB were reduced to the metallic Pt state more readily than those of the Pt/KB in the decreasing potential operation from 1.4 VRHE to 0.4 VRHE. The XAFS analysis for the Pt valences and the coordination numbers of Pt-O and Pt-Pt demonstrated that the Pt/AB catalyst is more durable than the Pt/KB catalyst in PEFC MEAs.

Mapping platinum species in polymer electrolyte fuel cells by spatially resolved XAFS techniques.

There is limited information on the mechanism for platinum oxidation and dissolution in Pt/C cathode catalyst layers of polymer electrolyte fuel cells (PEFCs) under the operating conditions though these issues should be uncovered for the development of next-generation PEFCs. Pt species in Pt/C cathode catalyst layers are mapped by a XAFS (X-ray absorption fine structure) method and by a quick-XAFS(QXAFS) method. Information on the site-preferential oxidation and leaching of Pt cathode nanoparticles around the cathode boundary and the micro-crack in degraded PEFCs is provided, which is relevant to the origin and mechanism of PEFC degradation.

Enhancement of mineral density and mechanical properties in root caries treated with silver diammine fluoride and glass ionomer cement, with emphasis on silver ion distribution.

OBJECTIVES: This study aimed to measure the distribution of silver ion (Ag+), mineral recovery, and nanohardness in carious lesions and comprehensively evaluate the degree of dentin restoration. METHODS: Sixty human teeth with root caries were randomly assigned to the control, silver diammine fluoride (SDF) [Safo], and SDF+Glass ionomer cement (GIC) treatment [Safo+Fuji] groups. Micro-computed tomography (micro-CT) was performed at five time points for each sample before/after treatment to evaluate mineral density within and around carious lesions. Three months following treatment, 12 samples were selected for synchrotron radiation X-ray fluorescence analysis to evaluate Ag+ distribution, while 15 samples were selected for nanoindentation. Data were analyzed using Dunnett's T3 test for micro-CT and Wilcoxon rank sum test with Bonferroni correction (p = 0.017) for nanoindentation. The correlation between hardness and mineral change was analyzed using the Spearman rank correlation coefficient. RESULTS: The Safo and Safo+Fuji groups showed significantly higher mineral recovery rates than did the control group (p < 0.001). In the Safo group, Ag+ accumulated in the deeper layers rather than the superficial layer of caries. In the Safo+Fuji group, Ag+ was found evenly distributed throughout caries, with only a few Ag+ detected in the GIC layer. Hardness in the Safo+Fuji group was significantly higher compared with the Safo group at depths in the range of 10-50 µm. CONCLUSION: In the presence of GICs, SDF exhibited high remineralization capacity when diffusing throughout carious lesions over time. Combined treatment with SDF and GIC could strengthen root dentin even in the presence of caries. CLINICAL SIGNIFICANCE: We found that combination treatment with SDF and GIC could increase mineral density in caries and improve the hardness of the tooth structure compared with fluoride-based agents alone. These findings might pave the way for future clinical trials to determine the therapeutic potential of nanotechnology-based restorative materials.

Structural kinetics of a Pt/C cathode catalyst with practical catalyst loading in an MEA for PEFC operating conditions studied by in situ time-resolved XAFS.

The structural kinetics of surface events on a Pt/C cathode catalyst in a membrane electrode assembly (MEA) with a practical catalyst loading (0.5 mgPt cm(-2)) for a polymer electrolyte fuel cell were investigated by in situ time-resolved X-ray absorption fine structure analysis (XAFS; time resolution: 100 ms) for the first time. The rate constants of structural changes in the Pt/C cathode catalyst in the MEA during voltage cycling were successfully estimated. For voltage-cycling processes, all reactions (electrochemical reactions and structural changes in the Pt catalyst) in the MEA were found to be much faster than those in an MEA with a thick cathode catalyst layer, but the in situ time-resolved XAFS analysis revealed that significant time lags similarly existed between the electrochemical reactions and the structural changes in the Pt cathode catalyst. The time-resolved XAFS also revealed differences in the structural kinetics of the Pt/C cathode catalyst for the voltage-cycling processes under N2 and air flows at the cathode.

Performance and characterization of a Pt-Sn(oxidized)/C cathode catalyst with a SnO2-decorated Pt3Sn nanostructure for oxygen reduction reaction in a polymer electrolyte fuel cell.

We have prepared and characterized a SnO2-decorated Pt-Sn(oxidized)/C cathode catalyst in a polymer electrolyte fuel cell (PEFC). Oxygen reduction reaction (ORR) performance of Pt/C (TEC10E50E) remained almost unchanged or even tended to reduce in repeated I-V load cycles, whereas the I-V load performance of the Pt-Sn(oxidized)/C prepared by controlled oxidation of a Pt-Sn alloy/C sample with the Pt3Sn phase revealed a significant increase with increasing I-V load cycles. The unique increase in the ORR performance of the Pt-Sn(oxidized)/C catalyst was ascribed to a promoting effect of SnO2 nano-islands formed on the surface of Pt3Sn core nanoparticles. Also in a rotating disk electrode (RDE) setup, the mass activity of an oxidized Pt3Sn/C catalyst was initially much lower than that of a Pt/C catalyst, but it increased remarkably after 5000 rectangular durability cycles and became higher than that of the fresh Pt/C. The maximum power density per electrochemical surface area for the Pt-Sn(oxidized)/C catalyst in a PEFC was about 5 times higher than that for the Pt/C catalyst at 0.1-0.8 A cm(-2) of the current density. In situ X-ray absorption near-edge structure (XANES) analysis at the Pt LIII-edge in increasing/decreasing potential operations and at the Sn K-edge in the I-V load cycles revealed a remarkable suppression of Pt oxidation compared with the Pt/C catalyst at higher potentials and no change in the Sn oxidation state, respectively, resulting in higher performance and stability of the Pt-Sn(oxidized)/C catalyst due to the SnO2 nano-islands under the PEFC operation conditions. The SnO2 nano-island decorated Pt-Sn(oxidized)/C catalyst with a Pt3Sn alloy nanostructure is regarded as a promising candidate for a PEFC cathode catalyst.

5D Analysis of Capacity Degradation in Battery Electrodes Enabled by Operando CT-XANES.

For devices encountering long-term stability challenges, a precise evaluation of degradation is of paramount importance. However, methods for comprehensively elucidating the degradation mechanisms in devices, particularly those undergoing dynamic chemical and mechanical changes during operation, such as batteries, are limited. Here, a method is presented using operando computed tomography combined with X-ray absorption near-edge structure spectroscopy (CT-XANES) that can directly track the evolution of the 3D distribution of the local capacity loss in battery electrodes during (dis)charge cycles, thereby enabling a five-dimensional (the 3D spatial coordinates, time, and chemical state) analysis of the degradation. This paper demonstrates that the method can quantify the spatiotemporal dynamics of the local capacity degradation within an electrode during cycling, which has been truncated by existing bulk techniques, and correlate it with the overall electrode performance degradation. Furthermore, the method demonstrates its capability to uncover the correlation among observed local capacity degradation within electrodes, reaction history during past (dis)charge cycles, and electrode microstructure. The method thus provides critical insights into the identification of degradation factors that are not available through existing methods, and therefore, will contribute to the development of batteries with long-term stability.