Effect of coloring and sintering on the translucency and biaxial strength of monolithic zirconia.

STATEMENT OF PROBLEM: The influences of coloring and sintering procedures on the optical and mechanical properties of monolithic zirconia have not been thoroughly investigated. PURPOSE: The purpose of this in vitro study was to investigate the effects of the coloring procedure and of varying final sintering temperatures on the translucency parameter (TP) and biaxial flexural strength (BFS) of monolithic zirconia. MATERIAL AND METHODS: Disk-shaped specimens (N=210) of 2 different monolithic zirconia brands (Vita YZ HTWhite [VYZa]; Vita YZ HTColor A2 [VYZb]; Prettau Zirkonzahn [PZ]; Prettau Anterior Zirkonzahn [PZA]) with a diameter of 15 mm and a thickness of 1.0 ±0.05 mm were prepared. Half of the specimens prepared from noncolored blocks (VYZa, PZ, and PZA) received coloring liquid application. Then, the specimens were divided into 3 subgroups (n=10) according to the final sintering temperatures (1350°C, 1450°C, and 1600°C). The TP was determined by using a reflection spectrophotometer, and the BFS was tested with the piston-on-3-ball method in a universal testing machine. Data were statistically analyzed by multivariate multiple regression and Bonferroni tests (α=.05). RESULTS: Significant differences were obtained among the groups based on the results of the TP and BFS (P<.05). The TP was affected by the changes in final sintering temperature. The varying final sintering temperatures demonstrated no significant effect on the BFS, except in group PZ (noncolored) that produced lower BFS when sintered at 1350°C than the subgroups sintered at 1450°C and 1600°C (P<.05). Coloring liquid application significantly decreased the TP of VYZa (sintered at 1350°C) but produced no significant effect on the groups PZ and PZA. Additionally, the coloring procedure had no significant effect on the BFS of tested materials (VYZa, PZ, and PZA) (P>.05). CONCLUSIONS: Increased sintering temperature leads to increased translucency with minimal impact on the BFS. The coloring procedure should be considered at the time of material selection to avoid possible reduction in translucency.

Sealing capability and marginal fit of titanium versus zirconia abutments with different connection designs.

PURPOSE: Limited data is available regarding the differences for possible microleakage problems and fitting accuracy of zirconia versus titanium abutments with various connection designs. The purpose of this in vitro study was to investigate the effect of connection design and abutment material on the sealing capability and fitting accuracy of abutments. MATERIALS AND METHODS: A total of 42 abutments with different connection designs [internal conical (IC), internal tri-channel (IT), and external hexagonal (EH)] and abutment materials [titanium (Ti) and zirconia (Zr)] were evaluated. The inner parts of implants were inoculated with 0.7 µL of polymicrobial culture (P. gingivalis, T. forsythia, T. denticola and F. nucleatum) and connected with their respective abutments under sterile conditions. The penetration of bacteria into the surrounding media was assessed by the visual evaluation of turbidity at each time point and the number of colony forming units (CFUs) was counted. The marginal gap at the implant- abutment interface (IAI) was measured by scanning electron microscope. The data sets were statistically analyzed using Kruskal-Wallis followed by Mann-Whitney U tests with the Bonferroni-Holm correction (α=.05). RESULTS: Statistically significant difference was found among the groups based on the results of leaked colonies (P<.05). The EH-Ti group characterized by an external hexagonal connection were less resistant to bacterial leakage than the groups EH-Zr, IT-Zr, IT-Ti, IC-Zr, and IC-Ti (P<.05). The marginal misfit (in µm) of the groups were in the range of 2.7-4.0 (IC-Zr), 1.8-5.3 (IC-Ti), 6.5-17.1 (IT-Zr), 5.4-12.0 (IT-Ti), 16.8-22.7 (EH-Zr), and 10.3-15.4 (EH-Ti). CONCLUSION: The sealing capability and marginal fit of abutments were affected by the type of abutment material and connection design.