Kinematic Performance of Gradually Variable Radius Posterior-Stabilized Primary TKA During Various Activities: An In Vivo Study Using Fluoroscopy.

BACKGROUND: Posterior-stabilized total knee arthroplasty (TKA) with gradually variable radii (G-curve) femoral condylar geometry is now available. It is believed that a G-curve design would lead to more mid-flexion stability leading to reduced incidence of paradoxical anterior slide. The objective of this study was to assess the in vivo kinematics for subjects implanted with this type of TKA under various conditions of daily living. METHODS: Tibiofemoral kinematics of 35 patients having posterior-stabilized TKA with G-curve design were analyzed using fluoroscopy while performing three activities: weight-bearing deep knee bend, gait, and walking down a ramp. The subjects were assessed for range of motion, condylar translation, axial rotation, cam-spine engagement, and condylar lift-off. RESULTS: The average weight-bearing flexion during deep knee bend was 111.4°. On average, the subjects exhibited 5.4 mm of posterior rollback of the lateral condyle and 2.0 mm of the medial condyle from full extension to maximum knee flexion. The femur consistently rotated externally with flexion, and the average axial rotation was 5.2°. Overall movement of the condyles during gait and ramp-down activity was small. No incidence of condylar lift-off was observed. CONCLUSION: Subjects in this study experienced consistent magnitudes of posterior femoral rollback and external rotation of the femur with weight-bearing flexion. The variation is similar to that previously reported for normal knee where the lateral condyle moves consistently posterior compared to the medial condyle. Subjects experienced low overall mid-flexion paradoxical anterior sliding and no incidence of condylar lift-off leading to mid-flexion stability.

In Vivo Kinematic Comparison of a Bicruciate Stabilized Total Knee Arthroplasty and the Normal Knee Using Fluoroscopy.

BACKGROUND: The bicruciate stabilized (BCS) total knee arthroplasty (TKA) features asymmetrical bearing geometry and dual substitution for the anterior cruciate ligament and posterior cruciate ligament (PCL). Previous TKA designs have not fully replicated normal knee motion, and they are characterized by lower magnitudes of overall rollback and axial rotation than the normal knee. METHODS: In vivo kinematics were derived for 10 normal knees and 40-second generation BCS TKAs all implanted by a single surgeon. Mobile fluoroscopy and three-dimensional-to-two-dimensional registration was used to analyze anterior-posterior motion of the femoral condyles and femorotibial axial rotation during weight-bearing flexion. Statistical analysis was conducted at the 95% confidence level. RESULTS: From 0° to 30° of knee flexion, the BCS subjects exhibited similar patterns of femoral rollback and axial rotation compared to normal knee subjects. From 30° to 60° of knee flexion, BCS subjects experienced negligible anterior-posterior motions and axial rotation while normal knees continued to rollback and externally rotate. Between 60° and 90° the BCS resumed posterior motion and, after 90°, axial rotation increased in a normal-like fashion. CONCLUSION: Similarities in early flexion kinematics suggest that the anterior cam-post is supporting normal-like anterior-posterior motion in the BCS subjects. Likewise, lateral femoral rollback and external rotation of the femur in later flexion provides evidence for appropriate substitution of the PCL via the posterior cam-post. Being discrete in nature, the dual cam-post mechanism does not lend itself to adequate substitution of the cruciate ligaments in mid-flexion during which anterior cruciate ligament tension is decreasing and PCL tension is increasing in the normal knee.

The impact of bone morphology on the outcome of the pivot shift test: a cohort study.

BACKGROUND: The presence of a positive pivot shift after surgical repair of the ACL is considered an important indicator of a failed reconstruction. The ability to predict the result of a pivot shift test after an ACL reconstruction using variables that can be measured prior to surgery could provide an indication of which patients may be at-risk of a poor surgical outcome.The purpose of this study was to determine whether structural characteristics of the femur and tibia, measured using plain radiographs, were associated with the result of the pivot shift test in unilateral ACL reconstructed patients. METHODS: Sixteen patients who had undergone unilateral ACL reconstruction were divided into two groups based on the results of manual pivot shift testing: 1) Pivot group; and 2) No pivot group. All patients had standing true lateral radiographs of both knees. Structural measurements of the tibia and femur were made on both knees. In addition, two new variables were created to describe the tibiofemoral mismatch: 1) Femur Tibia Size Ratio (FTSR); and 2) Tibia to Posterior Femoral Condyle Ratio (TPFCR). These measures were compared within groups and between groups. RESULTS: None of the individual structural characteristics were significantly different when compared between groups. No individual structural characteristics had a significant association with the presence of a positive pivot shift. When a between-group analysis was performed, both the FTSR (p < 0.03) and the TPFCR (p < 0.01) were significantly different between the Pivot group and the No Pivot group. A larger FTSR ratio, or a larger femur relative to the tibia, was associated with a positive pivot shift. A smaller TPFCR ratio, or a smaller tibial depth relative to the depth of the lateral posterior femoral condyle, was associated with a positive pivot shift. CONCLUSIONS: Structural characteristics in the lateral femoral condyle and lateral tibial plateau were found to be associated with the presence of a positive pivot shift. These characteristics could separate between patients in the Pivot group and the No Pivot group. Two indices, the FTSR and the TPFCR, provided better predictive value than individual characteristics in identifying patients with a knee that was structurally "at-risk" for developing a positive pivot shift.

Customized versus Patient-Sized Cruciate-Retaining Total Knee Arthroplasty: An In Vivo Kinematics Study Using Mobile Fluoroscopy.

BACKGROUND: Historically, knee arthroplasties have been designed using average patient anatomy. Recent advances in imaging and manufacturing have facilitated the development of customized prostheses designed to fit the unique shape of individual patients. The purpose of this study is to determine if improving implant design through customized total knee arthroplasty (TKA) improves kinematic function. METHODS: Using state-of-the-art mobile fluoroscopy, tibiofemoral kinematics were analyzed for 24 subjects with a customized individually made (CIM), cruciate-retaining TKA, and 14 subjects having an asymmetric condylar cruciate-retaining TKA. Subjects performed a weight-bearing deep knee bend and a rise from a seated position. Each patient was evaluated for weight-bearing range of motion, femorotibial translation, femorotibial axial rotation, and condylar liftoff occurrence. RESULTS: Subjects having a CIM TKA experienced greater weight-bearing knee flexion compared with the traditional posterior cruciate-retaining (PCR) TKA design. During flexion, the CIM TKA subjects consistently exhibited more posterior femoral rollback than the traditional PCR TKA subjects. The CIM TKA was found to have statistically greater axial rotation compared with the traditional PCR TKA (P = .05). Of note, only the CIM TKA patients experienced femoral internal rotation at full extension, as exhibited in a normal knee. Compared with the traditional PCR TKA, the CIM TKAs demonstrated minimal occurrences of paradoxical sliding and reverse rotation during flexion and extension. The CIM TKA subjects showed minimal liftoff and hence better stability in earlyflexion to midflexion compared with the traditional PCR subjects. CONCLUSION: The CIM TKA demonstrated kinematics more similar to a normal knee. Therefore, using customized implant technology through CIM TKA designs affords benefits including more normal motion compared with a traditional PCR TKA.

Single Versus Multiple-Radii Cruciate-Retaining Total Knee Arthroplasty: An In Vivo Mobile Fluoroscopy Study.

BACKGROUND: Previous fluoroscopic studies, using static C-arm systems, have shown nonnormal kinematic patterns in cruciate-retaining (CR) total knee arthroplasty (TKA). This study compares in vivo the kinematic differences in subjects implanted with single sagittal radius (SR) vs multiradii (MR) CR TKA for various activities using a novel mobile fluoroscopic system. METHODS: Using mobile fluoroscopy and 3D to 2D registration, tibiofemoral kinematics were analyzed for 25 subjects with an SR, symmetrical condylar CR TKA and 25 subjects with an MR, asymmetric condylar CR TKA for three dynamic weight-bearing activities: (1) deep knee bend (DKB), (2) walking up a ramp, and (3) walking down a ramp. RESULTS: During DKB, from full extension to maximum knee flexion, the SR (-0.43 ± 3.43 mm) and MR (-1.00 ± 3.23 mm) groups experienced statistically similar anterior/posterior (AP) motion in the lateral condyle. The SR (3.51 ± 2.68 mm) group had significant anterior movement compared to the MR (-0.42 ± 2.20 mm) group in the medial condyle. This resulted in a significantly larger amount of normal axial rotation experienced by the SR (5.20 ± 3.93°) group compared to the MR (0.75 ± 5.12°) group. During ramp activities, the SR TKA consistently exhibited a significantly more posterior position of both condyles compared to the MR TKA. CONCLUSION: Although the SR TKA exhibited larger amounts of axial rotation compared to the MR TKA in DKB, neither design exhibited weight-bearing kinematics as previously reported for the normal knee. Additional research on the normal knee for ramp activities is required to understand the importance of condylar position during these activities.

Kinematic difference between various geometric centers and contact points for tri-condylar bi-surface knee system.

The purpose of the study was to analyze the motion of contact points (CPs), lowest points (LPs), and component facet centers of tri-condylar implants. In vivo knee kinematics was assessed for 43 knees implanted with a multi-radii femoral component during deep knee bend activity, using a model fitting approach. Both LPs had the similar positions to the corresponding geometric centers of the femoral component, and the LP and geometric center angles represented the same component rotation angle defined by Grood and Suntay. Antero-posterior translation of both CPs was significantly overestimated, compared to LPs, and the CP angle showed significant differences from other rotation angles. In conclusion LPs seemed better to evaluate kinematics than CPs because polyethylene congruity had considerable effects on CP analysis.

Confirmation of long-term in vivo bearing mobility in eight rotating-platform TKAs.

BACKGROUND: Posterior-stabilized rotating-platform prostheses for TKAs were designed to improve contact mechanics at the femoral-polyethylene (PE) interface. Short-term followup studies have shown that the PE bearings rotate with respect to the tibia but might not necessarily track with the femur. It is important to know how kinematics in these designs change owing to long-term in vivo use. QUESTIONS/PURPOSES: We asked whether there is a significant change in the in vivo kinematic performance of a posterior-stabilized rotating-platform prosthesis at as much as 10 years postoperative. We specifically examined (1) relative femoral component-PE bearing and relative PE bearing-tibial tray motion; (2) relative AP motion of the femoral condyles with respect to the tibial tray; and (3) relative femorotibial condylar translations. METHODS: In vivo three-dimensional kinematics were evaluated for eight patients at 3 months, 15 months, 5 years, and 10 years after TKA with primary implantation of a posterior-stabilized rotating-platform prosthesis. Each patient performed deep knee bend activity, and three-dimensional kinematics were reconstructed from multiple fluoroscopic images using a three-dimensional to two-dimensional registration technique. Once complete, relative component axial rotation patterns, medial and lateral condyle motions throughout flexion, and the presence of femoral condylar lift-off were analyzed. RESULTS: Overall, tibial bearing rotation was maintained at 10 years postoperatively. There was no statistical difference between postoperative periods for any kinematic parameter except for femoral component-PE bearing axial rotation, which was reduced at the 10-year evaluation versus other assessment periods (p = 0.0006). The lack of statistical difference between postoperative evaluation periods indicates sustained overall implant kinematic performance. CONCLUSIONS: Our study showed that PE bearing-tibial tray mobility was maintained and that femoral component-PE bearing rotation was reduced at the 10-year followup. This suggests that the overall kinematic performance of this mobile-bearing implant is not negatively affected 10 years postoperatively. LEVEL OF EVIDENCE: Level III, retrospective study. See the Instructions for Authors for a complete description of levels of evidence.

In vivo determination of cam-post engagement in fixed and mobile-bearing TKA.

BACKGROUND: Kinematics vary, sometimes in important ways, among the different types of total knee arthroplasty (TKA) designs, yet differences between the in vivo mechanisms of cam-post engagement in rotating-platform posterior-stabilized (PS) TKA, bicruciate-stabilized TKA, and fixed-bearing PS TKA designs remain largely uncharacterized. QUESTIONS/PURPOSES: The objective of this study was to determine the cam-post mechanism interaction for subjects implanted with three different TKA designs. METHODS: In vivo, analysis was conducted for patients implanted with nine rotating-platform PS TKAs, five knees with a fixed-bearing PS TKA, and 10 knees with a bicruciate-stabilized TKA while performing a deep knee bend. Three-dimensional kinematics of the implant components were determined by analysis of fluoroscopic images during flexion. The distances between the interacting surfaces were measured throughout flexion and instances and locations of contact were identified. RESULTS: Seven of the 10 bicruciate-stabilized knees analyzed had the femoral component engaged with the anterior aspect of the tibial post at full extension. Posterior cam-post engagement occurred at 34° for the bicruciate-stabilized (range, 17°-68°), 93° for the fixed-bearing PS (range, 88°-100°), and at 97° (range, 90°-104°) for rotating-platform PS TKA. In bicruciate-stabilized and fixed-bearing PS knees, the contact initially occurred on the medial aspect of the posterior surface of the tibial post and then moved centrally and superiorly with increasing flexion. For rotating-platform PS TKA, it was located centrally on the posterior surface of the post at all times. CONCLUSIONS: This study suggests that mobility of the polyethylene might play an important role in ensuring central cam-post interaction in PS TKA. The polyethylene insert rotates axially in accordance with the rotating femur, maintaining central cam-post contact. This phenomenon was not observed in the fixed-bearing PS TKAs analyzed in this study. CLINICAL RELEVANCE: We speculate that this centralized symmetrical contact between the cam and posterior surface of the post could be beneficial clinically in terms of reducing wear of the posterior surface and particularly at the medial extremes of it.

Can post-cam function be replaced by addition of a third condyle in PS TKA?

The purpose of the study was to analyze the effectiveness of an additional ball and socket articulation in implanted knees and whether it can replicate post-cam function. Fifteen knees implanted with a cruciate substituting (CS) polyethylene without a post and ten knees implanted with a posterior stabilized (PS) polyethylene with a post were analyzed using 3D model fitting approach. Two types of designs showed similar posterior translation and similar axial rotation. Most of the contact points at the ball and socket joint stayed within the socket height for the PS group. This study indicates that the ball and socket joint is able to function as a replacement of the post-cam mechanism, which might serve as a new way to achieve posterior stability.

Femoral condylar contact points start and remain posterior in high flexing patients.

This study compares kinematic patterns of 136 patients following total knee arthroplasty with high post-operative knee flexion (HighFlex) versus kinematics of 114 patients with limited knee flexion (LowFlex) using a blocked stratified random sampling study design to reduce confounding and bias. The kinematics was collected using fluoroscopy and 2D to 3D registration for a weight-bearing deep knee bend activity. Both the lateral and the medial condylar contact positions for the HighFlex subjects were significantly more posterior than the LowFlex subjects at full extension and remained that way at all flexion angles. The amount translation of the contact points, axial orientation angle and axial rotation were found to be similar for the two groups. Lift-off was significantly higher in the LowFlex indicating mid-flexion instability.

The John Insall Award: control-matched evaluation of painful patellar Crepitus after total knee arthroplasty.

BACKGROUND: Patellar crepitus (PC) is reported in up to 14% of subjects implanted with cruciate-substituting total knee arthroplasty (TKA). Numerous etiologies of PC have been proposed. QUESTIONS/PURPOSES: We determined when painful PC typically occurs postoperatively and compared patients undergoing primary TKA who developed painful PC requiring subsequent surgery with a matched group without this complication to identify clinical, radiographic, and surgical variables associated with this complication. METHODS: From the databases of two institutions (greater than 4000 TKAs), we identified 60 patients who required surgery for painful PC from 2002 to 2008. This group was then compared with an identified control group of 60 TKA subjects without PC who were matched for the key variables of age, gender, and body mass index to determine clinical, radiographic, and surgical factors associated with the development of PC. RESULTS: The mean time to presentation of PC was 10.9 months. The incidence of PC correlated with a greater number of previous knee surgeries, decreased patellar component size, decreased composite patellar thickness, shorter preoperative and postoperative patellar tendon length, increased posterior femoral condylar offset, use of smaller femoral components and thicker tibial polyethylene inserts, and placement of the femoral component in a flexed posture. CONCLUSIONS: Many of the factors associated with an increased incidence of postoperative PC such as shortened patellar tendon length, use of smaller patellar components, decreased patellar composite thickness, and increased posterior femoral condylar offset may all increase quadriceps tendon contact forces against the superior aspect of the intercondylar box, increasing the risk of fibrosynovial proliferation and entrapment within the intercondylar region of the femoral component. Based on these findings, the authors recommend use of larger patellar components when possible, avoid oversection of the patella or increasing posterior femoral condylar offset, and advising patients preoperatively who have had previous knee surgery or demonstrate a shortened patellar tendon length of an increased risk of development of postoperative patellar crepitus. LEVEL OF EVIDENCE: Level III, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.

Kneeling is safe for patients implanted with medial-pivot total knee arthroplasty designs.

Nine ADVANCE (Wright Medical Technology, Arlington, TN)) Medial-Pivot (MP) and 9 ADVANCE Double-High total knee arthroplasties were analyzed under radiographic surveillance at standing, mid kneeling, and full kneeling. In vivo tibiofemoral contact positions were obtained using the 3- to 2-dimensional image registration technique. The contact in Double-High knee was always more posterior than that in the MP knee presumably because of the presence of the posterior cruciate ligament. The contact positions in both the designs moved anterior from standing to mid kneeling, moved posterior from mid kneeling to full kneeling, and remained within the intended articulation range of the implants. This study indicates that kneeling is safe in MP total knee arthroplasty even in the absence of a cam-post or posterior cruciate ligament.

Gap balancing versus measured resection technique for total knee arthroplasty.

Multiple differing surgical techniques are currently utilized to perform total knee arthroplasty (TKA). We compared knee arthroplasties performed using either a measured resection or gap balancing technique to determine if either operative technique provides superior coronal plane stability as measured by assessment of the incidence and magnitude of femoral condylar lift-off. We performed 40 TKA using a measured resection technique (20 PCL-retaining and 20 PCL-substituting) and 20 PCL-substituting TKA were implanted using gap balancing. All subjects were analyzed fluoroscopically while performing a deep knee bend. The incidence of coronal instability (femoral condylar lift-off) was then determined using a 3-D model fitting technique. The incidence of lift-off greater than 0.75 mm was 80% (maximum, 2.9 mm) and 70% (maximum, 2.5 mm) for the PCL-retaining and substituting TKA groups performed using measured resection versus 35% (maximum, 0.88 mm) for the gap-balanced group. Lift-off greater than 1 mm occurred in 60% and 45% of the PCL-retaining and -substituting TKA using measured resection versus none in the gap-balanced group. Rotation of the femoral component using a gap balancing technique resulted in better coronal stability which we suggest will improve functional performance and reduce polyethylene wear.

In vivo kinematics after a cruciate-substituting TKA.

UNLABELLED: Patterns of motion in the native knee show substantial variability. Guided motion prosthetic designs offer stability but may limit natural variability. To assess these limits, we therefore determined the in vivo kinematic patterns for patients having a cruciate-substituting TKA of one design and determined the intersurgeon variability associated with a guided-motion prosthetic design. Three-dimensional femorotibial contact positions were evaluated for 86 TKAs in 80 subjects from three different surgeons using fluoroscopy during a weightbearing deep knee bend. The average posterior femoral rollback of the medial and lateral condyles for all TKAs from full extension to maximum flexion was -14.0 mm and -23.0 mm, respectively. The average axial tibiofemoral rotation from full extension to maximum flexion for all TKAs was 10.8 degrees. The average weightbearing range of motion (ROM) was 109 degrees (range, 60 degrees-150 degrees; standard deviation, 18.7 degrees). Overall, the TKA showed axial rotation patterns similar to those of the normal knee, although less in magnitude. Surgeon-to-surgeon comparison revealed dissimilarities, showing the surgical technique and soft tissue handling influence kinematics in a guided-motion prosthetic design. LEVEL OF EVIDENCE: Level III, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.

Comparison of in vivo patellofemoral kinematics for subjects having high-flexion total knee arthroplasty implant with patients having normal knees.

This study compares the in vivo patellar kinematics of high-flexion posterior cruciate ligament-retaining and posterior-stabilized total knee arthroplasty (TKA) implants with that of the healthy knee. Twenty-seven subjects performing weight-bearing deep knee bends were analyzed under fluoroscopic surveillance from full extension to maximum flexion. The patellofemoral contact positions and patellar flexion were similar for both TKAs. At low flexion, the patellofemoral contact was significantly more distal on the healthy patella than on the TKA patella, but in deeper flexion, there was no difference among the 3 groups. The tibiopatellar angle was similar for all 3 groups, except at deep flexion where the healthy patella rotated significantly more than the implanted ones. Patellofemoral separation was observed in some TKA knees, whereas it was absent in the healthy knees.

In vivo patellofemoral forces in high flexion total knee arthroplasty.

This study compares the in vivo patellofemoral contact forces generated in high flexion fixed bearing posterior cruciate retaining Nexgen CR-Flex (PCR) and high flexion posterior stabilized Nexgen LPS-Flex (LPS) TKAs with that of normal knees from full knee extension to maximum weight bearing flexion. Ten patients with the PCR total knee arthroplasty (TKA), ten with the LPS TKA and seven patients having normal knees were fluoroscoped while performing a deep knee bend activity. In vivo femorotibial kinematics, obtained from 3D-to-2D registration technique, and patellar kinematics obtained by direct measurements from the fluoroscopic images were entered into a 3D inverse dynamics mathematical model to determine the in vivo contact forces at the knee. The variation in the patellofemoral and quadriceps forces with flexion were found to be similar across the three groups-increasing from full extension to 90 degrees of flexion, reaching a maximum between 90 degrees and 120 degrees of flexion and then decreasing until maximum flexion. At maximum knee flexion, these forces were found to be significantly lower in the normal knees than in the TKAs. The patellar ligament to quadriceps force ratio decreased with the increase in knee flexion while the patellofemoral to quadriceps force ratio increased. A strong correlation was found to exist between the patellofemoral forces, the femorotibial contact forces and the forces in the extensor mechanism. The PCR TKA in this study exhibited greater resemblance to the normal patients with respect to the patellofemoral forces than the LPS TKA though significant differences in the two implant types were not observed.

Lateral retinacular release rates in mobile- versus fixed-bearing TKA.

UNLABELLED: Controversy exists as to whether bearing mobility facilitates centralization of the extensor mechanism after TKA. To assess the incidence of lateral retinacular release, we retrospectively reviewed 1318 consecutive primary TKAs (1032 patients) performed by one surgeon using either a rotating-platform bearing (940) or a fixed bearing (378) from the same implant system. The selection of a fixed- versus mobile-bearing TKA was primarily based on age with patients younger than 70 years receiving a mobile-bearing TKA. We performed a lateral release whenever continuous symmetric patellar facet contact with the trochlear groove from 0 degrees to 90 degrees of flexion was not obtained using the rule of no thumb after tourniquet release. One hundred four of 1318 knees (7.9%) had a lateral release. We performed more lateral releases in the fixed-bearing group (14.3% [54 of 378]) than in the mobile-bearing group (5.3% [50 of 940]). Patellar tilt occurred more often in the mobile-bearing group (10% [94 of 940]) than in the fixed-bearing group (6.9% [26 of 378]), although the magnitude of mean patellar tilt was small in both groups (mobile-bearing 3.0 degrees ; fixed bearing 2.55 degrees ). No patient had patellar subluxation greater than 5 mm. We suspect the fewer lateral releases in the mobile-bearing group is the result of better extensor mechanism centralization provided by bearing rotation. LEVEL OF EVIDENCE: Level III, prognostic study. See the Guidelines for a complete description of levels of evidence.

Comparison of cervical spine kinematics using a fluoroscopic model for adjacent segment degeneration. Invited submission from the Joint Section on Disorders of the Spine and Peripheral Nerves, March 2007.

OBJECT: In this cervical spine kinematics study the authors evaluate the motions and forces in the normal, degenerative, and fused states to assess how alteration in the cervical motion segment affects adjacent segment degeneration and spondylosis. METHODS: Fluoroscopic images obtained in 30 individuals (10 in each group with disease at C5-6) undergoing flexion/extension motions were collected. Kinematic data were obtained from the fluoroscopic images and analyzed with an inverse dynamic mathematical model of the cervical spine that was developed for this analysis. RESULTS: During 20 degrees flexion to 15 degrees extension, average relative angles at the adjacent levels of C6-7 and C4-5 in the fused patients were 13.4 degrees and 8.8 degrees versus 3.7 degrees and 4.8 degrees in the healthy individuals. Differences at C3-4 averaged only about 1 degrees. Maximum transverse forces in the fused spines were two times the skull weight at C6-7 and one times the skull weight at C4-5, compared with 0.2 times the skull weight and 0.3 times the skull weight in the healthy individuals. Vertical forces ranged from 1.6 to 2.6 times the skull weight at C6-7 and from 1.2 to 2.5 times the skull weight at C4-5 in the patients who had undergone fusion, and from 1.4 to 3.1 times the skull weight and from 0.9 to 3.3 times the skull weight, respectively, in the volunteers. CONCLUSIONS: Adjacent-segment degeneration may occur in patients with fusion due to increased motions and forces at both adjacent levels when compared with healthy individuals in a comparable flexion and extension range.

In Vivo Three-Dimensional Patellar Mechanics: Normal Knees Compared with Domed and Anatomic Patellar Components.

BACKGROUND: Patellofemoral complications are a major cause of revision surgery following total knee arthroplasty (TKA). High forces occurring at the patellofemoral articulation coupled with a small patellofemoral contact area pose substantial design challenges. In this study, the three-dimensional (3D) in vivo mechanics of domed and anatomically shaped patellar components were compared with those of native patellae. METHODS: Ten normal knees, 10 treated with an LCS-PS (low contact stress-posterior stabilized) TKA (anatomically shaped patellar component), and 10 treated with a PFC Sigma RP-PS (press-fit condylar Sigma rotating platform-posterior stabilized) TKA (domed patellar component) were analyzed under fluoroscopic surveillance while the patient performed a weight-bearing deep knee bend from full knee extension to maximum knee flexion. Relevant bone geometries were segmented out from computed tomography (CT) scans, and computer-assisted-design (CAD) models of the implanted components were obtained from the manufacturer. Three-dimensional patellofemoral kinematics were obtained using a 3D-to-2D registration process. Contact mechanics were calculated using a distance map between the articulating patellar and femoral surfaces. RESULTS: Both patellar component designs exhibited good rotational kinematics and tracked well within the femoral trochlea when compared with the normal patella. The contact areas in the TKA groups peaked at 60° of knee flexion (mean and standard deviation, 201 ± 63.4 mm for the LCS-PS group and 218 ± 95.4 mm for the Sigma RP-PS group), and the areas were substantially smaller than those previously reported for the normal patella. Contact points in the TKA groups stayed close to the center of the patellar components. CONCLUSIONS: Both designs performed satisfactorily, although patellofemoral contact areas were reduced in comparison with those in the native patella. LEVEL OF EVIDENCE: Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

In vivo kinematic effects of ball and socket third condyle as a post-cam mechanism in tri-condylar knee implants.

BACKGROUND: Tri-condylar implants containing a ball and socket third condyle as a post-cam mechanism were developed to accommodate a lifestyle requiring frequent deep flexion activities. The purpose of the current study was to examine the kinematic effects of the ball and socket third condyle during a deep knee bend activity, and to confirm the contact status of the ball and socket joint. METHODS: Seventeen knees implanted with tri-condylar implants were analyzed using a 3D to 2D registration approach. A distance of less than 1mm denoted ball and socket contact. Medial and lateral contact positions and axial rotation were compared before and after contact. Moreover, the contact position at the third condyle and the center of the ball joint were analyzed. RESULTS: After the third condyle contact, posterior translation of the medial and lateral contact positions increased considerably. Meanwhile, the angular rotation remained still. The center of the third condyle did not move after contact, and the contact position at the third condyle remained low. CONCLUSIONS: The third condyle induced intensive posterior translation of both condyles, and did not prevent axial rotation, which was proved to work properly as a posterior stabilizing post-cam mechanism.