Tin-oxide nanoparticles deposited from a beam: what happens to the composition?

The debate around the oxidation states occurring in laboratory-prepared tin-oxide samples has been for a long time an obstacle for an unambiguous assignment of characterization studies performed on such samples. In particular the changes in the Sn core-level energies caused by oxidation - i.e. the chemical shifts - as measured by photoelectron spectroscopy (PES) have been under discussion. The assignment problem is especially pronounced for nanoscale structures, which are important for photovoltaics, electronics, catalysis, and gas sensing. The reasons for the difficulties lie both in the natural properties of tin oxides, which can have substantial deficiencies of oxygen and tin in the lattice, and in the shortcomings of the fabrication and PES-characterization procedures themselves. Our recent PES study on tin-oxide nanoparticles fabricated by vapour-aggregation gave a chemical shift two times larger than earlier reported for Sn(iv) oxide for the Sn 4d level. The implemented fabrication technique forms an in-vacuum beam of particles whose composition can be both controlled and characterized by PES. In the present work SnO and SnO2 nanoparticles fabricated this way were deposited from the beam and probed by PES directly, as well as after exposure to air. The deposited nanoparticle films were also imaged by TEM (Transmission Electron Microscopy). The effects of the deposition process and exposure to air on the chemical composition were studied. The PES study of deposited SnO2 nanoparticles in the Sn 4d and Sn 3d core-level regions revealed the same core level shift as for unsupported nanoparticles, indicating that the chemical composition is preserved in the deposition process. The TEM study demonstrated a crystalline structure of separate SnO2 particles with lattice constants close to the macroscopic Sn(iv)-oxide. The PES study on the particles exposed to air showed changes in the composition. For the film of initially SnO particles a higher intermediate oxide was created. For the SnO2 nanoparticle film a lower, but strong, intermediate oxide was observed, likely at the surface.

Aqueous solution/metal interfaces investigated in operando by photoelectron spectroscopy.

We describe a new in operando approach for the investigation of heterogeneous processes at solid/liquid interfaces with elemental and chemical specificity which combines the preparation of thin liquid films using the meniscus method with standing wave ambient pressure X-ray photoelectron spectroscopy [Nemsák et al., Nat. Commun., 5, 5441 (2014)]. This technique provides information about the chemical composition across liquid/solid interfaces with sub-nanometer depth resolution and under realistic conditions of solution composition and concentration, pH, as well as electrical bias. In this article, we discuss the basics of the technique and present the first results of measurements on KOH/Ni interfaces.

Dissociation of water on oxygen-covered Rh{111}.

The adsorption of water and coadsorption with oxygen on Rh{111} under ultrahigh vacuum conditions was studied using synchrotron-based photoemission and photoabsorption spectroscopy. Water adsorbs intact on the clean surface at temperatures below 154 K. Irradiation with x-rays, however, induces fast dissociation and the formation of a mixed OH+H(2)O layer indicating that the partially dissociated layer is thermodynamically more stable. Coadsorption of water and oxygen at a coverage below 0.3 monolayers has a similar effect, leading to the formation of a hydrogen-bonded network of water and hydroxyl molecules at a ratio of 3:2. The partially dissociated layers are more stable than chemisorbed intact water with the maximum desorption temperatures up to 30 K higher. For higher oxygen coverage, up to 0.5 monolayers, water does not dissociate and an intact water species is observed above 160 K, which is characterized by an O 1s binding energy 0.6 eV higher than that of chemisorbed water and a high desorption temperature similar to the partially dissociated layer. The extra stabilization is most likely due to hydrogen bonds with atomic oxygen.

Chemical composition and reactivity of water on hexagonal Pt-group metal surfaces.

The dissociation behaviour and valence-electronic structure of water adsorbed on clean and oxygen-covered Ru{0001}, Rh{111}, Pd{111}, Ir{111} and Pt{111} surfaces has been studied by high-resolution X-ray photoelectron spectroscopy with the aim of identifying similarities and trends within the Pt-group metals. On average, we find higher reactivity for the 4d metals (Ru, Rh, Pd) as compared to 5d (Ir, Pt), which is correlated with characteristic shifts in the 1b(1) and 3a(1) molecular orbitals of water. Small amounts of oxygen (< 0.2 ML) induce dissociation of water on all five surfaces, for higher coverages (> 0.25 ML) only intact water is observed. Under UHV conditions these higher coverages can only be reached on the 4d metals, the 5d metals are, therefore, not passivated.