RESUMO
Firstly, the electron density distribution of inductively coupled plasma (ICP) is measured by laser Thomson scattering (TS) method and the features of the ICP under the same experimental conditions are simulated by finite element method (FEM). The simulated results are in good agreement with the experimental results, which verifies the accuracy of the ICP generation simulation model. Secondly, the propagation characteristics of terahertz wave in ICP are measured by terahertz time domain spectroscopy (THz-TDS) and calculated by FEM according to the electron density distribution of ICP simulated in the first step above. The high consistency between the experimental and simulation results of terahertz wave propagation characteristics in ICP further proves the accuracy of terahertz wave transmission model in plasma and the feasibility of joint simulation with ICP generation simulation model.
RESUMO
The controllable growth of CsPbI3 perovskite thin films with desired crystal phase and morphology is crucial for the development of high efficiency inorganic perovskite solar cells (PSCs). The role of dimethylammonium iodide (DMAI) used in CsPbI3 perovskite fabrication was carefully investigated. We demonstrated that the DMAI is an effective volatile additive to manipulate the crystallization process of CsPbI3 inorganic perovskite films with different crystal phases and morphologies. The thermogravimetric analysis results indicated that the sublimation of DMAI is sensitive to moisture, and a proper atmosphere is helpful for the DMAI removal. The time-of-flight secondary ion mass spectrometry and nuclear magnetic resonance results confirmed that the DMAI additive would not alloy into the crystal lattice of CsPbI3 perovskite. Moreover, the DMAI residues in CsPbI3 perovskite can deteriorate the photovoltaic performance and stability. Finally, the PSCs based on phenyltrimethylammonium chloride passivated CsPbI3 inorganic perovskite achieved a record champion efficiency up to 19.03 %.
RESUMO
Neuromodulation aims to modulate the signaling activity of neurons or neural networks by the precise delivery of electrical stimuli or chemical agents and is crucial for understanding brain function and treating brain disorders. Conventional approaches, such as direct physical stimulation through electrical or acoustic methods, confront challenges stemming from their invasive nature, dependency on wired power sources, and unstable therapeutic outcomes. The emergence of stimulus-responsive delivery systems harbors the potential to revolutionize neuromodulation strategies through the precise and controlled release of neurochemicals in a specific brain region. This review comprehensively examines the biological barriers controlled release systems may encounter in vivo and the recent advances and applications of these systems in neuromodulation. We elucidate the intricate interplay between the molecular structure of delivery systems and response mechanisms to furnish insights for material selection and design. Additionally, the review contemplates the prospects and challenges associated with these systems in neuromodulation. The overarching objective is to propel the application of neuromodulation technology in analyzing brain functions, treating brain disorders, and providing insightful perspectives for exploiting new systems for biomedical applications.
Assuntos
Preparações de Ação Retardada , Humanos , Animais , Preparações de Ação Retardada/química , Encéfalo/metabolismo , Neurotransmissores/metabolismo , Neurotransmissores/química , Sistemas de Liberação de MedicamentosRESUMO
In recent years, hydrogel microsphere has attracted much attention due to its great potential in the field of skin repair. This paper reviewed the recent progress in the preparation strategy of hydrogel microsphere and its application in skin repair. In this review, several preparation methods of hydrogel microsphere were summarized in detail. In addition, the related research progress of hydrogel microspheres for skin repair was reviewed, and focused on the application of bioactive microspheres, antibacterial microspheres, hemostatic microspheres, and hydrogel microspheres as delivery platforms (hydrogel microspheres as a microcarrier of drugs, bioactive factors, or cells) in the field of skin repair. Finally, the limitations and future prospects of the development of hydrogel microspheres and its application in the field of skin repair were presented. It is hoped that this review can provide a valuable reference for the development of the preparation strategy of hydrogel microspheres and promote the application of hydrogel microspheres in skin repair.
RESUMO
Based on laser Thomson scattering (TS) measurements and finite element method (FEM) simulations of electron density in inductively coupled plasma (ICP), the simulated local pressure calibration curves of ICP generator are obtained by comparing the experimental and simulated electron density distributions and maxima. The equation coefficients of theoretical model associated with the ICP generator experimental system can be obtained by fitting the simulation curve with the least square method, and the theoretical pressure calibration curves under different absorbed powers can be further obtained. Combined with the vacuum gauge measurements, both the simulated and theoretical pressure calibration curves can give the true local pressure in the plasma. The results of the local pressure calibration at the different absorbed powers show that the density gradient from the vacuum gauge sensor to the center of the coil in ICP generator cavity becomes larger with the increase of electron density, resulting in a larger gap between the measured value and the pressure calibration value. This calibration method helps to grasp the local pressure of ICP as an external control factor and helps to study the physicochemical mechanism of ICP in order to achieve higher performance in ICP etching, material modification, etc.
RESUMO
Accurate measurements of electron temperature (Te) and electron density (ne) are important for understanding the properties of plasma, especially for the low-temperature plasma dominated by the free electrons. In this work, a high resolution laser Thomson scattering (LTS) diagnosis system with a software platform for processing data is established to accurately measure the Te and ne in low-temperature plasmas. In this system, a homemade Triple Grating Spectrometer (TGS) is elaborated to suppress the intense stray light and Rayleigh scattering light. The TGS with high etendue (with an f-number of f/3.3) and high spectral resolution (0.07 nm in full-width-half-maximum at 532 nm) allows the LTS system to measure the plasma with the ne and Te as low as 1.0 × 1017 m-3 and 0.1 eV, respectively. Besides the development of the experimental setup, a software platform is specially designed to automatically process the complicated LTS spectra to determine ne and Te in real time during the acquirement of data. The error analyses indicate that the uncertainty of ne is around 12% and the uncertainty of Te is about 10% when Te > 0.2 eV. Using the LTS system, we have successfully measured ne and Te in the cascaded arc plasma, nanosecond pulse discharge plasma, and inductively coupled plasma. The results demonstrate that the LTS system has significant potential for the diagnosis of various low temperature plasmas.
RESUMO
Organic-inorganic metal halide perovskite solar cells (PSCs) have been emerging as one of the most promising next generation photovoltaic technologies with a breakthrough power conversion efficiency (PCE) over 22%. However, aiming for commercialization, it still encounters challenges for the large-scale module fabrication, especially for flexible devices which have attracted intensive attention recently. Low-temperature processed high-performance electron-transporting layers (ETLs) are still difficult. Herein, we present a facile low-temperature synthesis of crystalline SnO2 nanocrystals (NCs) as efficient ETLs for flexible PSCs including modules. Through thermal and UV-ozone treatments of the SnO2 ETLs, the electron transporting resistance of the ETLs and the charge recombination at the interface of ETL/perovskite were decreased. Thus, the hysteresis-free highly efficient rigid and flexible PSCs were obtained with PCEs of 19.20 and 16.47%, respectively. Finally, a 5 × 5 cm2 flexible PSC module with a PCE of 12.31% (12.22% for forward scan and 12.40% for reverse scan) was fabricated with the optimized perovskite/ETL interface. Thus, employing presynthesized SnO2 NCs to fabricate ETLs has showed promising for future manufacturing.
RESUMO
Low-temperature solution-processed SnO2 as a promising electron-transport material for planar perovskite solar cells (PSCs) has attracted particular attention because of its outstanding properties such as high optical transparency or high electron mobility. However, low-temperature sol-gel processes used in the synthesis are inevitably affected by the humidity of the atmosphere, which results in a wide distribution in the performance of the prepared PSCs owing to the inability to control crystallinity and defects. Herein, a highly crystalline SnO2 film is synthesized using a simple water bath post-treatment, which can remove the surface residuals of SnCl4 on the SnO2 films, which is beneficial for the interface charge transport from the perovskite to the SnO2 electron-transport layer. An improved performance of the PSCs can be easily obtained applying this treatment, giving rise to a high power conversion efficiency (PCE) of 19.17 %, much higher than that of the pristine SnO2 -based device (17.59 %). Most importantly, the reproducibility of the devices has been greatly improved, independent of the environmental humidity. Therefore, the enhanced crystallinity of SnO2 has shown promise for future commercial PSC applications: 5â cm×5â cm PSC modules have achieved a PCE of 16.16 %.