Phase Tailoring of Ruddlesden-Popper Perovskite at Fixed Large Spacer Cation Ratio.

Ruddlesden-Popper (RP) metal halide perovskites are considered as promising optoelectronic materials due to their good environmental stability and desirable optoelectronic properties. However, the phase composition and ordering in the deposited film, with a fixed ratio of large organic spacer cation in the precursor solution, are hard to be further tailored for specific optoelectronic applications. Herein, it is shown that even with a fixed spacer cation ratio, the phase composition and ordering can still be largely regulated by utilizing different crystallization kinetics of various cations with the inorganic octahedral lead halide. By using two different short cations to compete with the large spacer cation, the phase composition can be continuously tailored from thin multiple quantum wells (MQWs) dominated to 3D perovskite dominated. The phase ordering can be reversed from small n phases' prior to large n phases' prior near the substrate. Finally, with the same amount of large spacer cation protection, the perovskite can be tailored for both high-performance electroluminescence and photovoltaics with favorable energetic landscape for the corresponding desired first-order excitonic recombination and second-order free electron-hole recombination, respectively. This exploration substantially contributes to the understanding of precise phase engineering in RP perovskite and may provide a new insight into the design of multiple functional devices.

Super air stable quasi-2D organic-inorganic hybrid perovskites for visible light-emitting diodes.

Solution processed organic-inorganic hybrid perovskites are emerging as a new generation materials for optoelectronics. However, the electroluminescence is highly limited in light emitting diodes (LED) due to the low exciton binding energy and the great challenge in stability. Here, we demonstrate a super air stable quasi-two dimensional perovskite film employing hydrophobic fluorine-containing organics as barrier layers, which can store in ambient for more than 4 months with no change. The dramatically reduced grain size of the perovskite crystal in contrast to three dimensional (3D) perovskites was achieved. Together with the natural quantum well of quasi-two dimensional perovskite confining the excitons to recombination, the LED exhibited the maximum luminance of 1.2 × 103 cd/m2 and current efficiency up to 0.3 cd/A, which is twenty fold enhancement than that of LED based on 3D analogues under the same condition.

Stability of Perovskite Solar Cells: A Prospective on the Substitution of the A†Cation and X†Anion.

In recent years, organometal trihalide perovskites have emerged as promising materials for low-cost, flexible, and highly efficient solar cells. Despite their processing advantages, before the technology can be commercialized the poor stability of the organic-inorganic hybrid perovskite materials with regard to humidity, heat, light, and oxygen has be to overcome. Herein, we distill the current state-of-the-art and highlight recent advances in improving the chemical stability of perovskite materials by substitution of the A-cation and X-anion. Our hope is to pave the way for the rational design of perovskite materials to realize perovskite solar cells with unprecedented improvement in stability.

Room Temperature Crystallized Phase-Pure α-FAPbI3 Perovskite with In-Situ Grain-Boundary Passivation.

Energy loss in perovskite grain boundaries (GBs) is a primary limitation toward high-efficiency perovskite solar cells (PSCs). Two critical strategies to address this issue are high-quality crystallization and passivation of GBs. However, the established methods are generally carried out discretely due to the complicated mechanisms of grain growth and defect formation. In this study, a combined method is proposed by introducing 3,4,5-Trifluoroaniline iodide (TFAI) into the perovskite precursor. The TFAI triggers the union of nano-sized colloids into microclusters and facilitates the complete phase transition of α-FAPbI3 at room temperature. The controlled chemical reactivity and strong steric hindrance effect enable the fixed location of TFAI and suppress defects at GBs. This combination of well-crystallized perovskite grains and effectively passivated GBs leads to an improvement in the open circuit voltage (Voc) of PSCs from 1.08 V to 1.17 V, which is one of the highest recorded Voc without interface modification. The TFAI-incorporated device achieved a champion PCE of 24.81%. The device maintained a steady power output near its maximum power output point, showing almost no decay over 280 h testing without pre-processing.

Green Solvent Polishing Enables Highly Efficient Quasi-2D Perovskite Solar Cells.

Preferred crystalline orientation at the surface of quasi-2D organic-inorganic halide perovskites is crucial to promote vertical carrier transport and interface carrier extraction, which further contribute to device efficiency and stability in photovoltaic applications. However, loose unoriented and defective surfaces are inevitably formed in the crystallization process, especially with the introduction of bulky organic cations into the quasi-2D perovskites. Here, a facile and effective surface polishing method using a natural-friendly green solvent, 2,2,2-trifluoroethanol, is proposed to reconstruct the surface. After solvent polishing, the randomly oriented phases containing trap sites on the surface are successfully removed, and the compact vertical-oriented phases underneath are revealed with less defectiveness and better smoothness, which greatly facilitates carrier transport and interfacial charge extraction. Consequently, the green solvent polished devices show a boosting efficiency of 18.38% with a high open-circuit voltage of 1.21 V. The devices also show improved storage and operational stability.

Intermediate Phase Free α-FAPbI3 Perovskite via Green Solvent Assisted Perovskite Single Crystal Redissolution Strategy.

Perovskite single-crystal redissolution (PSCR) strategy is highly desired for efficient formamidinium lead triiodide (FAPbI3 ) perovskite photovoltaics with enhanced phase purity, improved film quality, low trap-state density, and good stability. However, the phase transition and crystallization dynamics of FAPbI3 remain unclear in the PSCR process compared to the conventional fabrication from the mixing of precursor materials. In this work, a green-solvent-assisted (GSA) method is employed to synthesize centimeter-sized α-FAPbI3 single crystals, which serve as the high-purity precursor to fabricate perovskite films. The α-FAPbI3 PSCR strategy facilitates direct α-phase formation and inhibits the complex intermediate phases monitored by in situ grazing-incidence wide-angle X-ray scattering. Moreover, the α-phase stability is prolonged due to the relaxation of the residual lattice strain through the isotropic orientation phase growth. Consequently, the GSA-assisted PSCR strategy effectively promotes crystallization and suppresses non-radiative recombination in perovskite solar cells, which boosts the device efficiency from 22.08% to 23.92% with significantly enhanced open circuit voltage. These findings provide deeper insight into the PSCR process in terms of its efficacy in phase formation and lattice strain release. The green low-cost solvent may also offer a new and ideal solvent candidate for large-scale production of perovskite photovoltaics.

Strain Release and Defect Passivation in Formamidinium-Dominated Perovskite via a Novel in-Plane Thermal Gradient Assisted Crystallization Strategy.

It is essential to release annealing induced strain during the crystallization process to realize efficient and stable perovskite solar cells (PSCs), which does not seem achievable using the conventional annealing process. Here we report a novel and facile thermal gradient assisted crystallization strategy by simply introducing a slant angle between the preheated hot plate and the substrate. A distinct crystallization sequence resulted along the in-plane direction pointing from the hot side to the cool side, which effectively reduced the crystallization rate, controlled the perovskite grain growth, and released the in-plane tensile strain. Moreover, this strategy enabled uniform strain distribution in the vertical direction and assisted in reducing the defects and aligning the energy bands. The corresponding device demonstrated champion power conversion efficiencies (PCEs) of 23.70% and 21.04% on the rigid and flexible substrates, respectively. These highly stable rigid devices retained 97% of the initial PCE after 1097 h of storage and more than 80% of the initial PCE after 1000 h of continuous operation at the maximum power point. This novel strategy opens a simple and effective avenue to improve the quality of perovskite films and photovoltaic devices via strain modulation and defect passivation.

Discovery of Lead-Free Perovskites for High-Performance Solar Cells via Machine Learning: Ultrabroadband Absorption, Low Radiative Combination, and Enhanced Thermal Conductivities.

Exploring lead-free candidates and improving efficiency and stability remain the obstacle of hybrid organic-inorganic perovskite-based devices commercialization. Traditional trial-and-error methods seriously restrict the discovery especially for large search space, complex crystal structure and multi-objective properties. Here, the authors propose a multi-step and multi-stage screening scheme to accelerate the discovery of hybrid organic-inorganic perovskites A2 BB'X6 from a large number of candidates through combining machine learning with high-throughput calculations for pursuing excellent efficiency and thermal stability in solar cells. Followed by a series of screenings, the structure-property relationships mapping A2 BB'X6 properties are built and the predictions are close to reported experimental results. Successfully, four experimental-feasibly candidates with good stability, high Debye temperature and suitable band gap are screened out and further verified by density-functional theory calculations, in which the predicted efficiency for three lead-free candidates ((CH3 NH3 )2 AgGaBr6 , (CH3 NH3 )2 AgInBr6 and (C2 NH6 )2 AgInBr6 ) achieves 20.6%, 19.9% and 27.6% due to ultrabroadband absorption region ranging from UVC to IRC with excitonic radiative combination rates as low as 10 ps, large or intermediate polarons form with properties similar to CH3 NH3 PbI3 and the calculated thermal conductivities are 5.04, 4.39 and 5.16 Wm-1 K-1 , respectively, with Debye temperatures larger than 500 K, beneficial for suppression of both nonradiative combination and heat-induced degradation.

Photoelectrical Dynamics Uplift in Perovskite Solar Cells by Atoms Thick 2D TiS2 Layer Passivation of TiO2 Nanograss Electron Transport Layer.

A deficiency in the photoelectrical dynamics at the interface due to the surface traps of the TiO2 electron transport layer (ETL) has been the critical factor for the inferiority of the power conversion efficiency (PCE) in the perovskite solar cells. Despite its excellent energy level alignment with most perovskite materials, its large density of surface defect as a result of sub lattice vacancies has been the critical hurdle for an efficient photovoltaic process in the device. Here, we report that atoms thick 2D TiS2 layer grown on the surface of a (001) faceted and single-crystalline TiO2 nanograss (NG) ETL have effectively passivated the defects, boosting the charge extractability, carrier mobility, external quantum efficiency, and the device stability. These properties allow the perovskite solar cells (PSCs) to produce a PCE as high as 18.73% with short-circuit current density (Jsc), open-circuit voltage (Voc), and fill-factor (FF) values as high as 22.04 mA/cm2, 1.13 V, and 0.752, respectively, a 3.3% improvement from the pristine TiO2-NG-based PSCs. The present approach should find an extensive application for controlling the photoelectrical dynamic deficiency in perovskite solar cells.

Lead-Free Organic-Inorganic Hybrid Perovskites for Photovoltaic Applications: Recent Advances and Perspectives.

Organic-inorganic hybrid halide perovskites (e.g., MAPbI3 ) have recently emerged as novel active materials for photovoltaic applications with power conversion efficiency over 22%. Conventional perovskite solar cells (PSCs); however, suffer the issue that lead is toxic to the environment and organisms for a long time and is hard to excrete from the body. Therefore, it is imperative to find environmentally-friendly metal ions to replace lead for the further development of PSCs. Previous work has demonstrated that Sn, Ge, Cu, Bi, and Sb ions could be used as alternative ions in perovskite configurations to form a new environmentally-friendly lead-free perovskite structure. Here, we review recent progress on lead-free PSCs in terms of the theoretical insight and experimental explorations of the crystal structure of lead-free perovskite, thin film deposition, and device performance. We also discuss the importance of obtaining further understanding of the fundamental properties of lead-free hybrid perovskites, especially those related to photophysics.