RESUMO
BACKGROUND: Atrioventricular valve regurgitation (AVVR) is a devastating complication in children and young adults with congenital heart disease (CHD), particularly in patients with single ventricle physiology. Transcatheter edge-to-edge repair (TEER) is a rapidly expanding, minimally invasive option for the treatment of AVVR in adults that avoids the morbidity and mortality associated with open heart surgery. However, application of TEER in in CHD and in children is quite novel. We describe the development of a peri-procedural protocol including image-derived pre-intervention simulation, with successful application to four patients. AIMS: To describe the initial experience using the MitraClip system for TEER of dysfunctional systemic atrioventricular valves in patients with congential heart disease within a pediatric hospital. METHODS: A standardized screening and planning process was developed using cardiac magnetic resonance imaging, three dimensional echocardiography and both virtual and physical simulation. Procedures were performed using the MitraClip G4 system and patients were clinically followed post-intervention. RESULTS: A series of four CHD patients with at least severe AVVR were screened for suitability for TEER with the MitraClip system: three patients had single ventricle physiology and Fontan palliation, and one had repair of a common atrioventricular canal defect. Each patient had at least severe systemic AVVR and was considered at prohibitively high risk for surgical repair. Each patient underwent a standardized preprocedural screening protocol and image-derived modeling followed by the TEER procedure with successful clip placement at the intended location in all cases. CONCLUSIONS: The early results of our protocolized efforts to introduce TEER repair of severe AV valve regurgitation with MitraClip into the CHD population within our institution are encouraging. Further investigations of the use of TEER in this challenging population are warranted.
Assuntos
Técnica de Fontan , Cardiopatias Congênitas , Defeitos dos Septos Cardíacos , Implante de Prótese de Valva Cardíaca , Insuficiência da Valva Mitral , Criança , Humanos , Hospitais Pediátricos , Resultado do Tratamento , Cardiopatias Congênitas/diagnóstico por imagem , Cardiopatias Congênitas/cirurgia , Defeitos dos Septos Cardíacos/cirurgia , Técnica de Fontan/efeitos adversos , Técnica de Fontan/métodos , Implante de Prótese de Valva Cardíaca/efeitos adversos , Implante de Prótese de Valva Cardíaca/métodos , Insuficiência da Valva Mitral/diagnóstico por imagem , Insuficiência da Valva Mitral/cirurgiaRESUMO
The COVID-19 pandemic produced unprecedented challenges to healthcare and medical device manufacturing (e.g. personal protective device and replacement part shortages). Additive manufacturing, 3D printing, and the maker community were uniquely positioned to respond to these needs by providing in-house design and manufacturing to meet the needs of clinicians and hospitals. This paper reviews the pandemic response of Children's Hospital of Philadelphia CHAMP 3D Lab, a point-ofcare3D printing team that supports clinical and research projects across the hospital network. The CHAMP team responded to a variety of COVID-19 healthcare needs including providing protective eyewear and ventilator components, creating a transport hook, and designing a novel transparent facemask. This case series details our response to these needs, describing challenges experienced and lessons learned in overcoming them so that others may learn from our experiences. Challenges to responding to the pandemic included the need to handle urgent pandemic related requests in addition to our standard fare. This required us to not only expand our capacity without additional resources, but also to develop a system of prioritization. Specific changes made included: streamlining workflows, identifying safety review processes, and developing/enlisting a network of collaborators. Further, we consider how to transition to a future, post-pandemic world without losing the cohesive drive of emergency-induced innovation. This paper aims to share what we have learned and to encourage both teams currently engaged in the printing community and those looking to join it.