Easily processable highly ordered Langmuir-Blodgett films of quaterthiophene disiloxane dimer for monolayer organic field-effect transistors.

Self-assembly of highly soluble water-stable tetramethyldisiloxane-based dimer of α,α'-dialkylquaterthiophene on the water-air interface was investigated by Langmuir, grazing incidence X-ray diffraction, and X-ray reflectivity techniques. The conditions for formation of very homogeneous crystalline monolayer Langmuir-Blodgett (LB) films of the oligomer were found. Monolayer organic field-effect transistors (OFETs) based on these LB films as a semiconducting layer showed hole mobilities up to 3 × 10(-3) cm(2)/(V s), on-off ratio of 10(5), small hysteresis, and high long-term stability. The electrical performance of the LB films studied is close to that for the same material in the bulk or in the monolayer OFETs prepared from water vapor sensitive chlorosilyl derivatives of quaterthiophene by self-assembling from solution. These findings show high potential of disiloxane-based LB films in monolayer OFETs for large-area organic electronics.

Highly Sensitive Air-Stable Easily Processable Gas Sensors Based on Langmuir-Schaefer Monolayer Organic Field-Effect Transistors for Multiparametric H2S and NH3 Real-Time Detection.

A combination of low limit of detection, low power consumption, and portability makes organic field-effect transistor (OFET) chemical sensors promising for various applications in the areas of industrial safety control, food spoilage detection, and medical diagnostics. However, the OFET sensors typically lack air stability and restoration capability at room temperature. Here, we report on a new design of highly sensitive gas sensors based on Langmuir-Schaefer monolayer organic field-effect transistors (LS OFETs) prepared from organosilicon derivative of [1]benzothieno[3,2- b][1]-benzothiophene. The devices fabricated are able to operate in air and allow an ultrafast detection of different analytes at low concentrations down to tens of parts per billion. The sensors are reusable and can be utilized in real-time air-quality monitoring systems. We show that a direct current response of the LS OFET can be split into the alteration of various transistor parameters, responsible for the interactions with different toxic gases. The sensor response acquiring approach developed allows distinguishing two different gases, H2S and NH3, with a single sensing device. The results reported open new perspectives for the OFET-based gas-sensing technology and pave the way for easy detection of the other types of gases, enabling the development of complex air analysis systems based on a single sensor.

Luminescent Organic Semiconducting Langmuir Monolayers.

In recent years, monolayer organic field-effect devices such as transistors and sensors have demonstrated their high potential. In contrast, monolayer electroluminescent organic field-effect devices are still in their infancy. One of the key challenges here is to create an organic material that self-organizes in a monolayer and combines efficient charge transport with luminescence. Herein, we report a novel organosilicon derivative of oligothiophene-phenylene dimer D2-Und-PTTP-TMS (D2, tetramethyldisiloxane; Und, undecylenic spacer; P, 1,4-phenylene; T, 2,5-thiophene; TMS, trimethylsilyl) that meets these requirements. The self-assembled Langmuir monolayers of the dimer were investigated by steady-state and time-resolved photoluminescence spectroscopy, atomic force microscopy, X-ray reflectometry, and grazing-incidence X-ray diffraction, and their semiconducting properties were evaluated in organic field-effect transistors. We found that the best uniform, fully covered, highly ordered monolayers were semiconducting. Thus, the ordered two-dimensional (2D) packing of conjugated organic molecules in the semiconducting Langmuir monolayer is compatible with its high-yield luminescence, so that 2D molecular aggregation per se does not preclude highly luminescent properties. Our findings pave the way to the rational design of functional materials for monolayer organic light-emitting transistors and other optoelectronic devices.

Polymer Surface Engineering for Efficient Printing of Highly Conductive Metal Nanoparticle Inks.

An approach to polymer surface modification using self-assembled layers (SALs) of functional alkoxysilanes has been developed in order to improve the printability of silver nanoparticle inks and enhance adhesion between the metal conducting layer and the flexible polymer substrate. The SALs have been fully characterized by AFM, XPS, and WCA, and the resulting printability, adhesion, and electrical conductivity of the screen-printed metal contacts have been estimated by cross-cut tape test and 4-point probe measurements. It was shown that (3-mercaptopropyl)trimethoxysilane SALs enable significant adhesion improvements for both aqueous- and organic-based silver inks, approaching nearly 100% for PEN and PDMS substrates while exhibiting relatively low sheet resistance up to 0.1 Ω/sq. It was demonstrated that SALs containing functional -SH or -NH2 end groups offer the opportunity to increase the affinity of the polymer substrates to silver inks and thus to achieve efficient patterning of highly conductive structures on flexible and stretchable substrates.