RESUMO
Flexible Cu2 ZnSn(S,Se)4 (CZTSSe) solar cells show great potential due to non-toxicity and low cost. The quality of CZTSSe absorber suffering from the high-temperature selenization process is the key to overcoming open-circuit voltage (VOC ) deficit and obtaining high efficiency. In this work, the authors develop a selenization technique to improve the quality of the CZTSSe layer by pre-evaporation selenization. This method provides saturated selenium vapor at the beginning of the selenization process to promote the crystallization process. The oversaturated selenium source greatly shortens the annealing time at high temperatures. The prepared CZTSSe films have larger grains and fewer voids. The measurement of the space charge limited current shows that the defect density of the CZTSSe absorber is significantly reduced from 4.43 × 1013 cm-3 to 3.46 × 1013 cm-3 . Electrical tests show that the devices have better charge separation at the interface, resulting in a charge recombination lifetime, increasing from 133 to 197 µs. The power conversion efficiency of the flexible CZTSSe solar cell reaches 10.24% with VOC and the fill factor enhances to 463 mV and 62%, respectively. The safe non-toxicity and efficient selenization method is expected to provide a new strategy for high-efficiency flexible CZTSSe solar cells.
RESUMO
Ion doping is an effective strategy for achieving high-performance flexible Cu2 ZnSn(S,Se)4 (CZTSSe) solar cells by defect regulations. Here, a Li&Na co-doped strategy is applied to synergistically regulate defects in CZTSSe bulks. The quality absorbers with the uniformly distributed Li and Na elements are obtained using the solution method, where the acetates (LiAc and NaAc) are as additives. The concentration of the harmful CuZn anti-site defects is decreased by 8.13% after Li incorporation, and that of the benign NaZn defects is increased by 36.91% after Na incorporation. Synergistic Li&Na co-doping enhances the carrier concentration and reduces the interfacial defects concentration by one order of magnitude. As a result, the flexible CZTSSe solar cell achieves a power conversion efficiency (PCE) of 10.53% with certified 10.12%. Because of the high PCE and the homogeneous property, the Li&Na co-doped device is fabricated to a large area (2.38 cm2 ) and obtains 9.41% PCE. The co-doping investigation to synergistically regulate defects provides a new perspective for efficient flexible CZTSSe solar cells.
RESUMO
Flexible CZTSSe solar cells have attracted much attention due to their earth-abundant elements, high stability, and wide application prospects. However, the environmental problems caused by the high toxicity of the Cd in the buffer layers restrict the development of flexible CZTSSe solar cells. Herein, we develop a Cd-free flexible CZTSSe/ZnO solar cell. The influences of the ZnO films on device performances are investigated. The light absorption capacity of flexible CZTSSe solar cells is enhanced due to the removal of the CdS layer. The optimal thickness of the ZnO buffer layers and the appropriate annealing temperature of the CZTSSe/ZnO are 100 nm and 200 °C. Ultimately, the optimum flexible CZTSSe/ZnO device achieves an efficiency of 5.0%, which is the highest efficiency for flexible CZTSSe/ZnO solar cells. The systematic characterizations indicate that the flexible CZTSSe/ZnO solar cells based on the optimal conditions achieved quality heterojunction, low defect density and better charge transfer capability. This work provides a new strategy for the development of the environmentally friendly and low-cost flexible CZTSSe solar cells.
RESUMO
Environment-friendly flexible Cu2ZnSn(S,Se)4 (CZTSSe) solar cells show great potentials for indoor photovoltaic market. Indoor lighting is weak and multi-directional, thus the researches of photovoltaic device structures, techniques and performances face new challenges. Here, we design symmetrical bifacial CZTSSe solar cells on flexible Mo-foil substrate to efficiently harvest the indoor energy. Such devices are fabricated by double-sided deposition techniques to ensure bifacial consistency and save cost. We report 9.3% and 9% efficiencies for the front and back sides of the flexible CZTSSe solar cell under the standard sun light. Considering the indoor environment, we verify weak-light response performance of the devices under LED illumination and flexibility properties after thousands of bending. Bifacial CZTSSe solar cells in parallel achieve the superposition of double-sided output current from multi-directional light, significantly enhancing the area utilization rate. The present results and methods are expected to expand indoor photovoltaic applications.
RESUMO
The effect of Er addition on the fluidity and microstructure transformation of the as-cast and T5 heat-treated ZL205A alloys was investigated by optical microscope (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy dispersive spectrometer (EDS). The fluidity of the liquid metal after adding Er was tested and the fracture characteristics of the material were analyzed. The results indicated that Er was mainly dissolved into an α-Al matrix near the grain boundaries (GBs). It is easily segregated and enriched in the intersection of the GBs or the interface between the α and θ phase, which caused the intermetallic compounds to be distributed along the GBs to the neck and to fuse. Er could also inhibit the diffusion of Cu atoms in the process of solid solution, so that increased the residual eutectic structures in the crystal, while accelerating the precipitation progress of the Guinier-Preston (GP) zone and θ' phase and increasing precipitation of the θ phase. A small amount of precipitation of θ phase and micro-scale Er (0.1-0.5 wt %) can significantly increase the fluidity and reduce the casting defects, which can effectively improve the castability of the ZL205A alloy. The interface between the (Al8Cu4Er) phase and matrix is the main area of microcracks, through analyzing the fracture morphology.