RESUMO
Quinary and senary non-stoichiometric double perovskites such as Ba2Ca0.66Nb1.34-xFexO6-δ(BCNF) have been utilized for gas sensing, solid oxide fuel cells and thermochemical CO2reduction. Herein, we examined their potential as narrow bandgap semiconductors for use in solar energy harvesting. A cobalt co-doped BCNF, Ba2Ca0.66Nb0.68Fe0.33Co0.33O6-δ(BCNFCo), exhibited an optical absorption edge at â¼800 nm,p-type conduction and a distinct photoresponse up to 640 nm while demonstrating high thermochemical stability. A nanocomposite of BCNFCo and g-C3N4(CN) was prepared via a facile solvent-assisted exfoliation/blending approach using dichlorobenzene and glycerol at a moderate temperature. The exfoliation of g-C3N4followed by wrapping on perovskite established an effective heterojunction between the materials for charge separation. The conjugated 2D sheets of CN enabled better charge migration resulting in increased photoelectrochemical performance. A blend composed of 40 wt% perovskites and CN performed optimally, whilst achieving a photocurrent density as high as 1.5 mA cm-2for sunlight-driven water-splitting with a Faradaic efficiency as high as â¼88%.
RESUMO
Modification of carbon nitride based polymeric 2D materials for tailoring their optical, electronic and chemical properties for various applications has gained significant interest. The present report demonstrates the synthesis of a novel modified carbon nitride framework with a remarkable 3:5 C:N stoichiometry (C3N5) and an electronic bandgap of 1.76 eV, by thermal deammoniation of the melem hydrazine precursor. Characterization revealed that in the C3N5 polymer, two s-heptazine units are bridged together with azo linkage, which constitutes an entirely new and different bonding fashion from g-C3N4 where three heptazine units are linked together with tertiary nitrogen. Extended conjugation due to overlap of azo nitrogens and increased electron density on heptazine nucleus due to the aromatic π network of heptazine units lead to an upward shift of the valence band maximum resulting in bandgap reduction down to 1.76 eV. XRD, He-ion imaging, HR-TEM, EELS, PL, fluorescence lifetime imaging, Raman, FTIR, TGA, KPFM, XPS, NMR and EPR clearly show that the properties of C3N5 are distinct from pristine carbon nitride (g-C3N4). When used as an electron transport layer (ETL) in MAPbBr3 based halide perovskite solar cells, C3N5 outperformed g-C3N4, in particular generating an open circuit photovoltage as high as 1.3 V, while C3N5 blended with MA xFA1- xPb(I0.85Br0.15)3 perovskite active layer achieved a photoconversion efficiency (PCE) up to 16.7%. C3N5 was also shown to be an effective visible light sensitizer for TiO2 photoanodes in photoelectrochemical water splitting. Because of its electron-rich character, the C3N5 material displayed instantaneous adsorption of methylene blue from aqueous solution reaching complete equilibrium within 10 min, which is significantly faster than pristine g-C3N4 and other carbon based materials. C3N5 coupled with plasmonic silver nanocubes promotes plasmon-exciton coinduced surface catalytic reactions reaching completion at much low laser intensity (1.0 mW) than g-C3N4, which showed sluggish performance even at high laser power (10.0 mW). The relatively narrow bandgap and 2D structure of C3N5 make it an interesting air-stable and temperature-resistant semiconductor for optoelectronic applications while its electron-rich character and intrasheet cavity make it an attractive supramolecular adsorbent for environmental applications.
RESUMO
Anodically formed TiO2 nanotube arrays (TNTAs) constitute an optoelectronic platform that is being studied for use as a photoanode in photoelectrocatalytic cells, as an electron transport layer (ETL) in solar cells and photodetectors, and as an active layer for chemiresistive and microwave sensors. For optimal transport of charge carriers in these one-dimensional polycrystalline ordered structures, it is desirable to introduce a preferential texture with the grains constituting the nanotube walls aligned along the transport direction. Through x-ray diffraction analysis, we demonstrate that choosing the right water content in the anodization electrolyte and the use of a post-anodization zinc ion treatment can introduce a preferential texture in sub-micron length transparent TNTAs formed on non-native substrates. The incorporation of 1.5 atom% of Zn in TiO2 nanotubes prior to annealing, was found to consistently result in the strongest preferential orientation along the [001] direction. [001] oriented TNTAs exhibited a responsivity of 523 A W-1 at a bias of 2 V for 365 nm photons, which is among the highest reported performance values for ultraviolet photodetection using titania nanotubes. Furthermore, the textured nanotubes without a Zn2+ treatment showed a significantly enhanced performance in halide perovskite solar cells that used TNTAs as the ETL.
RESUMO
A fluorine-doped, chlorine-intercalated carbon nitride (CNF-Cl) photocatalyst has been synthesized for simultaneous improvements in light harvesting capability along with suppression of charge recombination in bulk g-C3N4. The formation of heterojunctions of these CNF-Cl nanosheets with low bandgap, earth abundant bismuth oxyiodide (BiOI) was achieved, and the synthesized heterojunctions were tested as active photoanodes in photoelectrochemical water splitting experiments. BiOI/CNF-Cl heterojunctions exhibited extended light harvesting with a band-edge of 680 nm and generated photocurrent densities approaching 1.3 mA cm-2 under AM1.5 G one sun illumination. Scanning Kelvin probe force microscopy under optical bias showed a surface potential of 207 mV for the 50% BiOI/CNF-Cl nanocomposite, while pristine CNF-Cl and BiOI had surface photopotential values of 83 mV and 98 mV, respectively, which in turn, provided direct evidence of superior charge separation in the heterojunction blends. Enhanced charge carrier separation and improved light harvesting capability in BiOI/CNF-Cl hybrids were found to be the dominant factors in increased photocurrent, compared to the pristine constituent materials.
RESUMO
Anodically formed, vertically oriented, self-organized cylindrical TiO2 nanotube arrays composed of the anatase phase undergo an interesting morphological and phase transition upon flame annealing to square-shaped nanotubes composed of both anatase and rutile phases. This is the first report on heterojunctions consisting of metal nanoparticles (NPs) deposited on square-shaped TiO2 nanotube arrays (STNAs) with mixed rutile and anatase phase content. A simple photochemical deposition process was used to form Cu, CuPt, and Pt NPs on the STNAs, and an enhancement in the visible light photoelectrochemical water splitting performance for the NP-decorated STNAs was observed over the bare STNAs. Under narrow band illumination by visible photons at 410 nm and 505 nm, Cu NP-decorated STNAs performed the best, producing photocurrents 80% higher and 50 times higher than bare STNAs, respectively. Probing the energy level structure at the NP-STNA interface using ultraviolet photoelectron spectroscopy revealed Schottky barrier formation in the NP-decorated STNAs, which assists in separating the photogenerated charge carriers, as also confirmed by longer charge carrier lifetimes in NP-decorated STNAs. While all the NP-decorated STNAs showed enhanced visible light absorption compared to the bare STNAs, only the Cu NPs exhibited a clear plasmonic behavior with an extinction cross section that peaked at 550 nm.
RESUMO
Doping quantum dots (QDs) is a problem that has been haunting researchers in the QD research community for years, even though doping techniques have been utilized for decades in conventional semiconductors. For the "self-purification" in colloidal QDs, engineering the surface ligands has emerged as an effective way to alter free carrier concentrations and doping types in colloidal QD solids. Halide-atomic ligands are the most popular ligands in producing PbS QD solids since they provide minimal dot-to-dot distance while maintain low in-gap trap states. However, previously reported halide surface treatment could only produce n-type QD solids. Here, we report the fabrication of p-type PbS QD solids using proton-assisted surface ligand exchange. We unveiled the origin of p-type doing in PbS QD solids, and it came from an unusual surface ligand; the HOH+ group formed using NH4X (X = Cl, Br, I) in methanol. We further fabricated QD solar cells using PbS-NH4Cl, a p-type QD solid predicted and proved by our theory and experiments. The champion device shows a high power conversion efficiency of 7.49%.
RESUMO
Leading edge p-i-n type halide perovskite solar cells (PSCs) severely underperform n-i-p PSCs. p-i-n type PSCs that use PEDOT:PSS hole transport layers (HTLs) struggle to generate open-circuit photovoltage values higher than 1 V. NiO HTLs have shown greater promise in achieving high Voc values albeit inconsistently. In this report, a NiO nanomesh with Ni3+ defect grown by the hydrothermal method was used to obtain PSCs with Voc values that consistently exceeded 1.10 V (champion Voc = 1.14 V). A champion device photoconversion efficiency of 17.75% was observed. Density functional theory modeling was used to understand the interfacial properties of the NiO/perovskite interface. The PCE of PSCs constructed using the Ni3+-doped NiO nanomesh HTL was â¼34% higher than that of conventional compact NiO-based perovskite solar cells. A suite of characterization techniques such as transmission electron microscopy, field emission scanning electron microscopy, intensity-modulated photocurrent spectroscopy, intensity-modulated photovoltage spectroscopy, time-resolved photoluminescence, steady-state photoluminescence, and Kelvin probe force microscopy provided evidence of better film quality, enhanced charge transfer, and suppressed charge recombination in PSCs based on hydrothermally grown NiO nanostructures.
RESUMO
Heterojunctions of the low bandgap semiconductor bismuth oxyiodide (BiOI) with bulk multilayered graphitic carbon nitride (g-C3N4) and few layered graphitic carbon nitride sheets (g-C3N4-S) are synthesized and investigated as an active photoanode material for sunlight driven water splitting. HR-TEM and elemental mapping reveals formation of a unique heterostructure between BiOI platelets and the carbon nitride (g-C3N4 and g-C3N4-S) network that consisted of dendritic BiOI nanoplates surrounded by g-C3N4 sheets. The presence of BiOI in g-C3N4-S/BiOI and g-C3N4-S/BiOI nanocomposites extends the visible light absorption profile from 500 nm up to 650 nm. Due to excellent charge separation in g-C3N4/BiOI and g-C3N4-S/BiOI, evident from quenching of the carbon nitride photoluminescence (PL) and a decrease in the PL lifetime, a significant increase in photoelectrochemical performance is observed for both types of g-C3N4-BiOI heterojunctions. In comparison to heterojunctions of bulk g-C3N4 with BiOI, the nanocomposite consisting of few layered sheets of g-C3N4 and BiOI exhibits higher photocurrent density due to lower recombination in few layered sheets. A synergistic trap passivation and charge separation is found to occur in the g-C3N4-S/BiOI nanocomposite heterostructure which results in a higher photocurrent and a lower charge transfer resistance.
RESUMO
The electron diffusion length (Ln) is smaller than the hole diffusion length (Lp) in many halide perovskite semiconductors meaning that the use of ordered one-dimensional (1D) structures such as nanowires (NWs) and nanotubes (NTs) as electron transport layers (ETLs) is a promising method of achieving high performance halide perovskite solar cells (HPSCs). ETLs consisting of oriented and aligned NWs and NTs offer the potential not merely for improved directional charge transport but also for the enhanced absorption of incoming light and thermodynamically efficient management of photogenerated carrier populations. The ordered architecture of NW/NT arrays affords superior infiltration of a deposited material making them ideal for use in HPSCs. Photoconversion efficiencies (PCEs) as high as 18% have been demonstrated for HPSCs using 1D ETLs. Despite the advantages of 1D ETLs, there are still challenges that need to be overcome to achieve even higher PCEs, such as better methods to eliminate or passivate surface traps, improved understanding of the hetero-interface and optimization of the morphology (i.e., length, diameter, and spacing of NWs/NTs). This review introduces the general considerations of ETLs for HPSCs, deposition techniques used, and the current research and challenges in the field of 1D ETLs for perovskite solar cells.