Titanium Oxyfluoride as a Material for Negative Electrodes of Lithium-Ion Batteries.

A study of the electrochemical characteristics of titanium oxyfluoride obtained with the direct interaction of titanium with hydrofluoric acid is reported. Two materials T1 and T2 synthesized under different conditions in which some TiF3 is formed in T1 are compared. Both materials exhibit conversion-type anode properties. Based on the analysis of the charge-discharge curves of the half-cell, a model is proposed according to which the first electrochemical introduction of lithium occurs in two stages: the first stage is the irreversible reaction resulting in a reduction in Ti4+/3+, and the second stage is the reversible reaction with a change in the charge state Ti3+/1.5+. The difference in material behavior is quantitative: T1 has a higher reversible capacity but lower cycling stability and a slightly higher operating voltage. The Li diffusion coefficient determined from the CVA data for both materials averages 1.2-3.0 × 10-14 cm2/s. A distinctive feature of titanium oxyfluoride anodes is the asymmetry in kinetic characteristics that revealed themselves during lithium embedding and extraction. In the long cycling regime, the excess of Coulomb efficiency over 100% was found in the present study.

Micro-mesoporous submicron silica particles with pore size tunable in a wide range: synthesis, properties and prospects for LED manufacturing.

An approach has been developed that allows the synthesis of submicron spherical silica particles with a controlled micro-mesoporous structure possessing a large specific surface area (up to 1300 m2g-1). Particle synthesis is carried out by the hydrolysis of a mixture of various organosilanes mostly associated either with CTAB or with each other. A change in the concentration of CTAB in the reaction mixture apparently leads to a change in the formation mechanism of nuclei for the silica particle growth, which allows for varying the diameter of the synthesized particles in the range from 40-450 nm. The effect of the composition of the silica precursor ([3-(methacryloyloxy)propyl]trimethoxysilane, (3-aminopropyl)triethoxysilane and tetraethoxysilane) on the formation process and porosity of the resulting particles is studied. It was shown that by simply varying the ratio of organosilanes in the composition of the precursor, one can control the pore diameter of the particles in a wide range from 0.6-15 nm. The large-pore (up to 15 nm) silica particles are used as a matrix for the spatial distribution of luminescent carbon dots. The incorporation of carbon dots into SiO2particles prevents their aggregation leading to emission quenching after drying, thus allowing us to obtain highly luminescent composite particles. LEDs based on the obtained composite material show bright visible luminescence with spectral characteristics similar to that of a commercial cold white LED.

Stability of Graphene/Nafion Composite in PEM FC Electrodes.

Ensuring the stable operation of proton exchange membrane fuel cells is conducive to their real-world application. A promising direction for stabilizing electrodes is the stabilization of the ionomer via the formation of surface compounds with graphene. A comprehensive study of the (electrochemical, chemical, and thermal) stability of composites for fuel cell electrodes containing a modifying additive of few-layer graphene was carried out. Electrochemical stability was studied by cycling the potential on a disk electrode for 5000 cycles. Chemical stability was assessed via the resistance of the composites to H2O2 treatment using ion-selective potentiometry. Thermal stability was studied using differential thermal analysis. Composites were characterized by UV-Vis spectroscopy, Raman spectroscopy, EDX, and SEM. It was shown that graphene inhibits Nafion degradation when exposed to heat. Contrariwise, Nafion is corrosive to graphene. During electrochemical and chemical exposure, the determining change for carbon-rich composites is the carbon loss (oxidation) of the carbon material. In the case of carbon-poor composites, the removal of fluorine and sulfur from the Nafion polymer with their partial replacement by oxygen prevails. In all cases, the F/S ratio is stable. The dispersity of Nafion in a sample affects its chemical stability more than the G/Nafion ratio does.